08-05-2012 07:59 AM
I am a little new to this and still going to college, I see you guys have really good support here. I bought a 3500XL switch off ebay to help me learn some cisco equipment as my instructor suggested it would be of great help getting ahead. I have done my basic configuration of the switch by setting up my switch ip address, enabling the vty 0 4 password and all but when i use SecureCRT to connect it gives me the error "The remote system refused the connection." and I cant seem to figure it out. I thought maybe the IP address I setup was conflicting somehow so I reassigned it to the last ip 192.168.100.254 instead of 192.168.100.1 and still no luck. I double checked and even setup the password from vty 0-15 just to make sure I had enough ports open to connect. Here is what my config looks like
Current configuration:
!
version 12.0
no service pad
service timestamps debug uptime
service timestamps log uptime
service password-encryption
!
hostname Neo
!
enable secret 5 (Left Out)
!
username James password 7 (Left Out)
!
!
!
!
!
ip subnet-zero
ip domain-name (Left Out).com
!
!
!
interface FastEthernet0/1
!
interface FastEthernet0/2
!
interface FastEthernet0/3
!
interface FastEthernet0/4
!
interface FastEthernet0/5
!
interface FastEthernet0/6
!
interface FastEthernet0/7
!
interface FastEthernet0/8
!
interface FastEthernet0/9
!
interface FastEthernet0/10
!
interface FastEthernet0/11
!
interface FastEthernet0/12
!
interface FastEthernet0/13
!
interface FastEthernet0/14
!
interface FastEthernet0/15
!
interface FastEthernet0/16
!
interface FastEthernet0/17
!
interface FastEthernet0/18
!
interface FastEthernet0/19
!
interface FastEthernet0/20
!
interface FastEthernet0/21
!
interface FastEthernet0/22
!
interface FastEthernet0/23
!
interface FastEthernet0/24
!
interface FastEthernet0/25
!
interface FastEthernet0/26
!
interface FastEthernet0/27
!
interface FastEthernet0/28
!
interface FastEthernet0/29
!
interface FastEthernet0/30
!
interface FastEthernet0/31
!
interface FastEthernet0/32
!
interface FastEthernet0/33
!
interface FastEthernet0/34
!
interface FastEthernet0/35
!
interface FastEthernet0/36
!
interface FastEthernet0/37
!
interface FastEthernet0/38
!
interface FastEthernet0/39
!
interface FastEthernet0/40
!
interface FastEthernet0/41
!
interface FastEthernet0/42
!
interface FastEthernet0/43
!
interface FastEthernet0/44
!
interface FastEthernet0/45
!
interface FastEthernet0/46
!
interface FastEthernet0/47
!
interface FastEthernet0/48
!
interface GigabitEthernet0/1
!
interface GigabitEthernet0/2
!
interface VLAN1
ip address 192.168.100.254 255.255.255.0
no ip directed-broadcast
no ip route-cache
!
ip default-gateway (Left Out)
snmp-server engineID local 0000000902000009B7473E00
snmp-server community private RW
snmp-server community public RO
banner motd ^C
#########################################################
DO NOT LOG ON UNLESS YOU HAVE BEEN PERMITTED BY THE OWNER
#########################################################
^C
!
line con 0
password 7 (Left Out)
login
transport input none
stopbits 1
line vty 0 4
password 7 (Left Out)
login
line vty 5 15
login
!
end
08-05-2012 10:31 PM
You need to set up ip default gateway to enable remote access.
Sent from Cisco Technical Support iPhone App
08-06-2012 04:41 AM
How do you connect your PC/laptop to the switch? using which cable? what ip address do you give to your PC? it should be in the same subnet as the switch.
Can you ping the PC from the switch and vice versa?