cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
292
Views
0
Helpful
1
Replies

Pix 501 VPN no connectivity to inside network

7jgray
Level 1
Level 1

I can VPN to PIX 501 but I have no connectivity to internal hosts. Here is my configuration.

PIX Version 6.3(4)

interface ethernet0 auto

interface ethernet1 100full

nameif ethernet0 outside security0

nameif ethernet1 inside security100

enable password xxx

passwd xxx

hostname borlandpix

domain-name borland.com

fixup protocol dns maximum-length 512

fixup protocol ftp 21

fixup protocol h323 h225 1720

fixup protocol h323 ras 1718-1719

fixup protocol http 80

fixup protocol rsh 514

fixup protocol rtsp 554

fixup protocol sip 5060

fixup protocol sip udp 5060

fixup protocol skinny 2000

fixup protocol smtp 25

fixup protocol sqlnet 1521

fixup protocol tftp 69

names

access-list inside_outbound_nat0_acl permit ip any 10.101.1.0 255.255.255.248

access-list outside_cryptomap_dyn_20 permit ip any 10.101.1.0 255.255.255.248

pager lines 24

mtu outside 1500

mtu inside 1500

ip address outside pppoe setroute

ip address inside 192.168.1.1 255.255.255.0

ip audit info action alarm

ip audit attack action alarm

ip local pool vpn_pool 10.101.1.1-10.101.1.5

pdm history enable

arp timeout 14400

global (outside) 1 interface

nat (inside) 0 access-list inside_outbound_nat0_acl

nat (inside) 1 0.0.0.0 0.0.0.0 0 0

timeout xlate 3:00:00

timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00

timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00

timeout uauth 0:05:00 absolute

aaa-server TACACS+ protocol tacacs+

aaa-server TACACS+ max-failed-attempts 3

aaa-server TACACS+ deadtime 10

aaa-server RADIUS protocol radius

aaa-server RADIUS max-failed-attempts 3

aaa-server RADIUS deadtime 10

aaa-server LOCAL protocol local

http server enable

http 192.168.1.0 255.255.255.0 inside

no snmp-server location

no snmp-server contact

snmp-server community public

no snmp-server enable traps

floodguard enable

sysopt connection permit-ipsec

crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac

crypto dynamic-map outside_dyn_map 20 match address outside_cryptomap_dyn_20

crypto dynamic-map outside_dyn_map 20 set transform-set ESP-3DES-MD5

crypto map outside_map 65535 ipsec-isakmp dynamic outside_dyn_map

crypto map outside_map client authentication LOCAL

crypto map outside_map interface outside

isakmp enable outside

isakmp nat-traversal 20

isakmp policy 20 authentication pre-share

isakmp policy 20 encryption 3des

isakmp policy 20 hash md5

isakmp policy 20 group 2

isakmp policy 20 lifetime 86400

vpngroup x address-pool vpn_pool

vpngroup x idle-time 1800

vpngroup x password ********

telnet 192.168.1.0 255.255.255.0 inside

telnet timeout 5

ssh timeout 5

console timeout 0

vpdn group isp request dialout pppoe

vpdn group isp localname x

vpdn group isp ppp authentication pap

vpdn username x password x

dhcpd address 192.168.1.10-192.168.1.20 inside

dhcpd lease 3600

dhcpd ping_timeout 750

dhcpd auto_config outside

dhcpd enable inside

username dena password xxx

encrypted privilege 2

terminal width 80

Cryptochecksum:xxx

: end

1 Reply 1

ajagadee
Cisco Employee
Cisco Employee

After you configured the Pix for VPN and NAT 0 access-list, did you do a "clear xlate". If not, do a clear xlate, VPN into the Pix 501 and then see if you can access the LAN behind the pix.

If not, do post the outputs of "Show crypto isakmp sa" and "Show crypto ipsec sa" from the Pix when you are VPNed in.

Regards,

Arul