10-07-2012 09:47 AM
Hello CISCO masters,
I am a CCNA student and I would like to know the SSH configuration in advance.
I have a CISCO 1841 router with ROM: System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)
, I'm trying to issue a command crypto key generate rsa general modulos 1024 but it keeps on saying that this command is unrecognized. - Does it mean that this router is not capable for that service?
what should i do to make ssh work on that flatform?
thanks and regards,
Francis
Solved! Go to Solution.
10-07-2012 10:30 AM
Hi Francis,
You will need an image that supports SSH (images with k9)
Yes. Starting with Cisco IOS Software Release 12.4(1), SSH is supported in all images with the following exceptions: IP Base without Crypto and Enterprise Base without Crypto.
Use this command: Router(config)#crypto key generate rsa
and you ll find out.
Configure the remote incoming vty terminal lines to accept Telnet and SSH.
Router(config)#line vty 0 4
Router(config-line)#privilege level 15
Router(config-line)#login local
Router(config-line)#transport input telnet ssh
Router(config-line)#exit
CustomerRouter(config)#crypto key generate rsa
How many bits in the modulus [512] 768
CustomerRouter(config)#exit
Verify that SSH is enabled and the version being used.
CustomerRouter#show ip ssh
Regards
Please rate if it helps.
10-09-2012 11:09 AM
Apart from those commands as sandeep stated here... you need to set ip domain-name as well for generating the key. Because you key will get generated based on your hostname... i.e.
Please do rate if the given information helps.
By
Karthik
10-10-2012 11:50 AM
Hi Francis,
Those advanced IP Services are compatible with cisco 1841 routers..... current IOS is in specific to broadband which has some limited facilities..... for eg advip ios has much more features of IP SLA but broadband IOS has only IP SLA Responder feature.... Like this way you have many other differences mate.... :-)
You can check the list of features available in that IOS by checking the cisco feature navigator which gives you list of facility available through each IOS....
You can check for which are all features you need for then you can choose the right IOS...
http://tools.cisco.com/ITDIT/CFN/Dispatch?act=rlsSelect&task=search&searchby=platform
in the above link you can click and select the software as IOS and platform as 1841 then press continue.... there you ahve the options to slect IOS code....
for eg in you case 124-15.T15.... you have to select thru major release as 12.4 T and then you can select the exact release as 12.4-15.T15 for getting the exact results...
Hope this helps.
Please do rate if the given information helps.
By
Karthik
10-07-2012 10:30 AM
Hi Francis,
You will need an image that supports SSH (images with k9)
Yes. Starting with Cisco IOS Software Release 12.4(1), SSH is supported in all images with the following exceptions: IP Base without Crypto and Enterprise Base without Crypto.
Use this command: Router(config)#crypto key generate rsa
and you ll find out.
Configure the remote incoming vty terminal lines to accept Telnet and SSH.
Router(config)#line vty 0 4
Router(config-line)#privilege level 15
Router(config-line)#login local
Router(config-line)#transport input telnet ssh
Router(config-line)#exit
CustomerRouter(config)#crypto key generate rsa
How many bits in the modulus [512] 768
CustomerRouter(config)#exit
Verify that SSH is enabled and the version being used.
CustomerRouter#show ip ssh
Regards
Please rate if it helps.
10-09-2012 11:09 AM
Apart from those commands as sandeep stated here... you need to set ip domain-name as well for generating the key. Because you key will get generated based on your hostname... i.e.
Please do rate if the given information helps.
By
Karthik
10-10-2012 09:15 AM
Hello,
Thanks a lot for both of you, two thumbs up for your answer, another question. which of these two IOS would i use to replace my current IOS?
a.) c1841-advipservicesk9-mz.124-15.T15.bin ---- the IOS of the router i bought from my friend
b.) c1841-advipservicesk9-mz.124-16b.bin --------- the IOS of the router i bought from my friend
these are the two IOS i found inside the flash of that router, i just want to confirm if hese are compatible to 1841 (below) and which file should i use?
a.) c1841-broadband-mz.150-1.M3.bin --------- This is the current IOS of my router, what does it do? what are the feature behind this Cisco IOS Software, 1841 Software (C1841-BROADBAND-M), Version 15.0(1)M3, RELEASE SOFTWARE (fc2)
thanks in advance.
Francis
10-10-2012 11:50 AM
Hi Francis,
Those advanced IP Services are compatible with cisco 1841 routers..... current IOS is in specific to broadband which has some limited facilities..... for eg advip ios has much more features of IP SLA but broadband IOS has only IP SLA Responder feature.... Like this way you have many other differences mate.... :-)
You can check the list of features available in that IOS by checking the cisco feature navigator which gives you list of facility available through each IOS....
You can check for which are all features you need for then you can choose the right IOS...
http://tools.cisco.com/ITDIT/CFN/Dispatch?act=rlsSelect&task=search&searchby=platform
in the above link you can click and select the software as IOS and platform as 1841 then press continue.... there you ahve the options to slect IOS code....
for eg in you case 124-15.T15.... you have to select thru major release as 12.4 T and then you can select the exact release as 12.4-15.T15 for getting the exact results...
Hope this helps.
Please do rate if the given information helps.
By
Karthik
10-10-2012 10:44 PM
Hi Karthik,
Thank you so much for that awesome information that i got from you, now i am ready to upgrade my IOS so that i could start my remote SSH access as well as site to site VPN configuration.
Regards,
Francis
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide