VPN behind cable modem

[joe@carmonnetwork.com]

I am working on setting up a VPN with a client behind a cable modem. I am using an ASA5506-X and they have an ASA5505.   After using the wizard to setup the connection I am unable to see the tunnel.

Result of the command: "show crypto ikev1 sa"

There are no IKEv1 SAs



Result of the command: "show crypto isakmp sa"

There are no IKEv1 SAs

There are no IKEv2 SAs

Here is my config

Result of the command: "show config"

: Saved

:
: Serial Number: JAD21290D2D
: Hardware:   ASA5506, 4096 MB RAM, CPU Atom C2000 series 1250 MHz, 1 CPU (4 cores)
: Written by enable_15 at 14:04:27.854 UTC Sun Mar 18 2018
!
ASA Version 9.8(1)
!
hostname ciscoasa
enable password $sha512$5000$pRPXY7l1tcpumENRZJ7ZXA==$uysBLrtmJeq8y+EtxjbJaA== pbkdf2
names

!
interface GigabitEthernet1/1
 nameif outside
 security-level 0
 ip address dhcp setroute
!
interface GigabitEthernet1/2
 bridge-group 1
 nameif inside_1
 security-level 100
!
interface GigabitEthernet1/3
 bridge-group 1
 nameif inside_2
 security-level 100
!
interface GigabitEthernet1/4
 bridge-group 1
 nameif inside_3
 security-level 100
!
interface GigabitEthernet1/5
 bridge-group 1
 nameif inside_4
 security-level 100
!
interface GigabitEthernet1/6
 bridge-group 1
 nameif inside_5
 security-level 100
!
interface GigabitEthernet1/7
 bridge-group 1
 nameif inside_6
 security-level 100
!
interface GigabitEthernet1/8
 bridge-group 1
 nameif inside_7
 security-level 100
!
interface Management1/1
 management-only
 no nameif
 no security-level
 no ip address
!
interface BVI1
 nameif inside
 security-level 100
 ip address 192.168.1.1 255.255.255.0
!
ftp mode passive
same-security-traffic permit inter-interface
object network obj_any1
 subnet 0.0.0.0 0.0.0.0
object network obj_any2
 subnet 0.0.0.0 0.0.0.0
object network obj_any3
 subnet 0.0.0.0 0.0.0.0
object network obj_any4
 subnet 0.0.0.0 0.0.0.0
object network obj_any5
 subnet 0.0.0.0 0.0.0.0
object network obj_any6
 subnet 0.0.0.0 0.0.0.0
object network obj_any7
 subnet 0.0.0.0 0.0.0.0
access-list outside_cryptomap extended permit ip interface inside interface outside
pager lines 24
logging asdm informational
mtu outside 1500
mtu inside_1 1500
mtu inside_2 1500
mtu inside_3 1500
mtu inside_4 1500
mtu inside_5 1500
mtu inside_6 1500
mtu inside_7 1500
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
no arp permit-nonconnected
arp rate-limit 16384
!
object network obj_any1
 nat (inside_1,outside) dynamic interface
object network obj_any2
 nat (inside_2,outside) dynamic interface
object network obj_any3
 nat (inside_3,outside) dynamic interface
object network obj_any4
 nat (inside_4,outside) dynamic interface
object network obj_any5
 nat (inside_5,outside) dynamic interface
object network obj_any6
 nat (inside_6,outside) dynamic interface
object network obj_any7
 nat (inside_7,outside) dynamic interface
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 sctp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
timeout conn-holddown 0:00:15
timeout igp stale-route 0:01:10
user-identity default-domain LOCAL
aaa authentication login-history
http server enable
http 192.168.1.0 255.255.255.0 inside_1
http 192.168.1.0 255.255.255.0 inside_2
http 192.168.1.0 255.255.255.0 inside_3
http 192.168.1.0 255.255.255.0 inside_4
http 192.168.1.0 255.255.255.0 inside_5
http 192.168.1.0 255.255.255.0 inside_6
http 192.168.1.0 255.255.255.0 inside_7
no snmp-server location
no snmp-server contact
service sw-reset-button
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS esp-aes esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transport
crypto ipsec ikev2 ipsec-proposal DES
 protocol esp encryption des
 protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal 3DES
 protocol esp encryption 3des
 protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES
 protocol esp encryption aes
 protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES192
 protocol esp encryption aes-192
 protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES256
 protocol esp encryption aes-256
 protocol esp integrity sha-1 md5
crypto ipsec security-association pmtu-aging infinite
crypto map outside_map 1 match address outside_cryptomap
crypto map outside_map 1 set peer 96.80.240.49
crypto map outside_map 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 1 set ikev2 ipsec-proposal AES256 AES192 AES 3DES DES
crypto map outside_map interface outside
crypto ca trustpool policy
crypto ikev2 policy 1
 encryption aes-256
 integrity sha
 group 5 2
 prf sha
 lifetime seconds 86400
crypto ikev2 policy 10
 encryption aes-192
 integrity sha
 group 5 2
 prf sha
 lifetime seconds 86400
crypto ikev2 policy 20
 encryption aes
 integrity sha
 group 5 2
 prf sha
 lifetime seconds 86400
crypto ikev2 policy 30
 encryption 3des
 integrity sha
 group 5 2
 prf sha
 lifetime seconds 86400
crypto ikev2 policy 40
 encryption des
 integrity sha
 group 5 2
 prf sha
 lifetime seconds 86400
crypto ikev2 enable outside
crypto ikev1 enable outside
crypto ikev1 policy 10
 authentication pre-share
 encryption aes-256
 hash sha
 group 2
 lifetime 86400
crypto ikev1 policy 20
 authentication rsa-sig
 encryption aes-256
 hash sha
 group 2
 lifetime 86400
crypto ikev1 policy 40
 authentication pre-share
 encryption aes-192
 hash sha
 group 2
 lifetime 86400
crypto ikev1 policy 50
 authentication rsa-sig
 encryption aes-192
 hash sha
 group 2
 lifetime 86400
crypto ikev1 policy 70
 authentication pre-share
 encryption aes
 hash sha
 group 2
 lifetime 86400
crypto ikev1 policy 80
 authentication rsa-sig
 encryption aes
 hash sha
 group 2
 lifetime 86400
crypto ikev1 policy 100
 authentication pre-share
 encryption 3des
 hash sha
 group 2
 lifetime 86400
crypto ikev1 policy 110
 authentication rsa-sig
 encryption 3des
 hash sha
 group 2
 lifetime 86400
crypto ikev1 policy 130
 authentication pre-share
 encryption des
 hash sha
 group 2
 lifetime 86400
crypto ikev1 policy 140
 authentication rsa-sig
 encryption des
 hash sha
 group 2
 lifetime 86400
telnet timeout 5
ssh stricthostkeycheck
ssh timeout 5
ssh key-exchange group dh-group1-sha1
console timeout 0

dhcpd auto_config outside
!
dhcpd address 192.168.1.5-192.168.1.254 inside
dhcpd enable inside
!
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
group-policy GroupPolicy_96.80.240.49 internal
group-policy GroupPolicy_96.80.240.49 attributes
 vpn-tunnel-protocol ikev1 ikev2
dynamic-access-policy-record DfltAccessPolicy
tunnel-group 96.80.240.49 type ipsec-l2l
tunnel-group 96.80.240.49 general-attributes
 default-group-policy GroupPolicy_96.80.240.49
tunnel-group 96.80.240.49 ipsec-attributes
 ikev1 pre-shared-key *****
 ikev2 remote-authentication pre-shared-key *****
 ikev2 local-authentication pre-shared-key *****
!
class-map inspection_default
 match default-inspection-traffic
!
!
policy-map type inspect dns preset_dns_map
 parameters
  message-length maximum client auto
  message-length maximum 512
  no tcp-inspection
policy-map global_policy
 class inspection_default
  inspect dns preset_dns_map
  inspect ftp
  inspect h323 h225
  inspect h323 ras
  inspect rsh
  inspect rtsp
  inspect esmtp
  inspect sqlnet
  inspect skinny  
  inspect sunrpc
  inspect xdmcp
  inspect sip  
  inspect netbios
  inspect tftp
  inspect ip-options
!
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:66a255c63c3c1178cc10239d0c44cf72

I believe the problem is either my cable modem or my NAT configuration. I am not certain specifically which it is.

[joe@carmonnetwork.com]

The wizard produced the following command sting/Error

[OK] object network NETWORK_OBJ_172.30.0.0_24
      object network NETWORK_OBJ_172.30.0.0_24
[OK] subnet 172.30.0.0 255.255.255.0
[OK] object network NETWORK_OBJ_192.168.0.0_24
      object network NETWORK_OBJ_192.168.0.0_24
[OK] subnet 192.168.0.0 255.255.255.0
[OK] access-list outside_cryptomap line 1 extended permit ip 192.168.0.0 255.255.255.0 172.30.0.0 255.255.255.0
[OK] group-policy GroupPolicy_96.80.240.46 internal
[OK] group-policy GroupPolicy_96.80.240.46 attributes
      group-policy GroupPolicy_96.80.240.46 attributes
[OK] vpn-tunnel-protocol ikev2 ikev1
[OK] exit
[OK] tunnel-group 96.80.240.46 type ipsec-l2l
[OK] tunnel-group 96.80.240.46 general-attributes
      tunnel-group 96.80.240.46 general-attributes
[OK] default-group-policy GroupPolicy_96.80.240.46
[OK] tunnel-group 96.80.240.46 ipsec-attributes
      tunnel-group 96.80.240.46 ipsec-attributes
[OK] ikev1 pre-shared-key **********
[OK] ikev2 local-authentication pre-shared-key **********
[OK] ikev2 remote-authentication pre-shared-key **********
[OK] isakmp keepalive threshold 10 retry 2
[OK] crypto map outside_map 1 match address outside_cryptomap
[OK] crypto map outside_map 1 set  peer  96.80.240.46
[OK] crypto map outside_map 1 set  ikev1 transform-set  ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
[OK] crypto map outside_map 1 set  ikev2 ipsec-proposal  DES 3DES AES AES192 AES256
[ERROR] nat (inside,outside) 1 source static NETWORK_OBJ_192.168.0.0_24 NETWORK_OBJ_192.168.0.0_24 destination static NETWORK_OBJ_172.30.0.0_24 NETWORK_OBJ_172.30.0.0_24 no-proxy-arp route-lookup
    
nat (inside,outside) 1 source static NETWORK_OBJ_192.168.0.0_24 NETWORK_OBJ_192.           ^168.0.0_24 destination static NETWORK_OBJ_172.30.0.0_24 NETWORK_OBJ_172.30.0.0_2
4 no-proxy-arp route-lookup

ERROR: % Invalid input detected at '^' marker.

[Mohammed al Baqari]

Have you created the object groups

[joe@carmonnetwork.com]

After running the wizard the object groups are created. Running the command in the CLI results in the exact same message.

[Richard Burts]

I note several things which may be causing the issue

- this is the access list for crypto in the show config

access-list outside_cryptomap extended permit ip interface inside interface outside

and this is the access list in the commands that you entered

[OK] access-list outside_cryptomap line 1 extended permit ip 192.168.0.0 255.255.255.0 172.30.0.0 255.255.255.0

you do need to replace the version in the config. However the version you are trying to complete has a problem that your source address of 192.168.0.0 does not match with the address configured on your inside interface 192.168.1.0.

- you might want to try your nat statement which gets the error without the  route-lookup parameter.

- your ASA is using DHCP to get its IP address. Are you sure that the remote peer is using a dynamic crypto map entry?

- can you verify IP connectivity from your ASA to the address of the remote peer 96.80.240.46 

- can you verify that the peer has IP connectivity to the address of your ASA?

HTH

Rick

[joe@carmonnetwork.com]

I will try your suggestions, but how can I verify connectivity?

- can you verify IP connectivity from your ASA to the address of the remote peer 96.80.240.46 

- can you verify that the peer has IP connectivity to the address of your ASA?

[Richard Burts]

The most simple way to verify connectivity is to ping the other address (perhaps specifying the source address as the local peer address if needed).

HTH

Rick

[joe@carmonnetwork.com]

I can ping the 96.80 address from my IP, but my IP is not "pingable" from the 96.80 address. I believe this is the result of my ISP blocking that traffic as it is a residential IP address.

I am able to do a packet track successfully from my inside_1 interface to an IP address on the peer network. So this may be an issue at the ISP level.

[joe@carmonnetwork.com]

Here is my new config.

Result of the command: "show config"

: Saved

:
: Serial Number: JAD21290D2D
: Hardware:   ASA5506, 4096 MB RAM, CPU Atom C2000 series 1250 MHz, 1 CPU (4 cores)
: Written by enable_15 at 14:04:27.854 UTC Sun Mar 18 2018
!
ASA Version 9.8(1)
!
hostname ciscoasa
enable password $sha512$5000$pRPXY7l1tcpumENRZJ7ZXA==$uysBLrtmJeq8y+EtxjbJaA== pbkdf2
names

!
interface GigabitEthernet1/1
 nameif outside
 security-level 0
 ip address dhcp setroute
!
interface GigabitEthernet1/2
 bridge-group 1
 nameif inside_1
 security-level 100
!
interface GigabitEthernet1/3
 bridge-group 1
 nameif inside_2
 security-level 100
!
interface GigabitEthernet1/4
 bridge-group 1
 nameif inside_3
 security-level 100
!
interface GigabitEthernet1/5
 bridge-group 1
 nameif inside_4
 security-level 100
!
interface GigabitEthernet1/6
 bridge-group 1
 nameif inside_5
 security-level 100
!
interface GigabitEthernet1/7
 bridge-group 1
 nameif inside_6
 security-level 100
!
interface GigabitEthernet1/8
 bridge-group 1
 nameif inside_7
 security-level 100
!
interface Management1/1
 management-only
 no nameif
 no security-level
 no ip address
!
interface BVI1
 nameif inside
 security-level 100
 ip address 192.168.1.1 255.255.255.0
!
ftp mode passive
same-security-traffic permit inter-interface
object network obj_any1
 subnet 0.0.0.0 0.0.0.0
object network obj_any2
 subnet 0.0.0.0 0.0.0.0
object network obj_any3
 subnet 0.0.0.0 0.0.0.0
object network obj_any4
 subnet 0.0.0.0 0.0.0.0
object network obj_any5
 subnet 0.0.0.0 0.0.0.0
object network obj_any6
 subnet 0.0.0.0 0.0.0.0
object network obj_any7
 subnet 0.0.0.0 0.0.0.0
access-list outside_cryptomap extended permit ip interface inside interface outside
pager lines 24
logging asdm informational
mtu outside 1500
mtu inside_1 1500
mtu inside_2 1500
mtu inside_3 1500
mtu inside_4 1500
mtu inside_5 1500
mtu inside_6 1500
mtu inside_7 1500
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
no arp permit-nonconnected
arp rate-limit 16384
!
object network obj_any1
 nat (inside_1,outside) dynamic interface
object network obj_any2
 nat (inside_2,outside) dynamic interface
object network obj_any3
 nat (inside_3,outside) dynamic interface
object network obj_any4
 nat (inside_4,outside) dynamic interface
object network obj_any5
 nat (inside_5,outside) dynamic interface
object network obj_any6
 nat (inside_6,outside) dynamic interface
object network obj_any7
 nat (inside_7,outside) dynamic interface
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 sctp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
timeout conn-holddown 0:00:15
timeout igp stale-route 0:01:10
user-identity default-domain LOCAL
aaa authentication login-history
http server enable
http 192.168.1.0 255.255.255.0 inside_1
http 192.168.1.0 255.255.255.0 inside_2
http 192.168.1.0 255.255.255.0 inside_3
http 192.168.1.0 255.255.255.0 inside_4
http 192.168.1.0 255.255.255.0 inside_5
http 192.168.1.0 255.255.255.0 inside_6
http 192.168.1.0 255.255.255.0 inside_7
no snmp-server location
no snmp-server contact
service sw-reset-button
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS esp-aes esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transport
crypto ipsec ikev2 ipsec-proposal DES
 protocol esp encryption des
 protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal 3DES
 protocol esp encryption 3des
 protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES
 protocol esp encryption aes
 protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES192
 protocol esp encryption aes-192
 protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES256
 protocol esp encryption aes-256
 protocol esp integrity sha-1 md5
crypto ipsec security-association pmtu-aging infinite
crypto map outside_map 1 match address outside_cryptomap
crypto map outside_map 1 set peer 96.80.240.49
crypto map outside_map 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 1 set ikev2 ipsec-proposal AES256 AES192 AES 3DES DES
crypto map outside_map interface outside
crypto ca trustpool policy
crypto ikev2 policy 1
 encryption aes-256
 integrity sha
 group 5 2
 prf sha
 lifetime seconds 86400
crypto ikev2 policy 10
 encryption aes-192
 integrity sha
 group 5 2
 prf sha
 lifetime seconds 86400
crypto ikev2 policy 20
 encryption aes
 integrity sha
 group 5 2
 prf sha
 lifetime seconds 86400
crypto ikev2 policy 30
 encryption 3des
 integrity sha
 group 5 2
 prf sha
 lifetime seconds 86400
crypto ikev2 policy 40
 encryption des
 integrity sha
 group 5 2
 prf sha
 lifetime seconds 86400
crypto ikev2 enable outside
crypto ikev1 enable outside
crypto ikev1 policy 10
 authentication pre-share
 encryption aes-256
 hash sha
 group 2
 lifetime 86400
crypto ikev1 policy 20
 authentication rsa-sig
 encryption aes-256
 hash sha
 group 2
 lifetime 86400
crypto ikev1 policy 40
 authentication pre-share
 encryption aes-192
 hash sha
 group 2
 lifetime 86400
crypto ikev1 policy 50
 authentication rsa-sig
 encryption aes-192
 hash sha
 group 2
 lifetime 86400
crypto ikev1 policy 70
 authentication pre-share
 encryption aes
 hash sha
 group 2
 lifetime 86400
crypto ikev1 policy 80
 authentication rsa-sig
 encryption aes
 hash sha
 group 2
 lifetime 86400
crypto ikev1 policy 100
 authentication pre-share
 encryption 3des
 hash sha
 group 2
 lifetime 86400
crypto ikev1 policy 110
 authentication rsa-sig
 encryption 3des
 hash sha
 group 2
 lifetime 86400
crypto ikev1 policy 130
 authentication pre-share
 encryption des
 hash sha
 group 2
 lifetime 86400
crypto ikev1 policy 140
 authentication rsa-sig
 encryption des
 hash sha
 group 2
 lifetime 86400
telnet timeout 5
ssh stricthostkeycheck
ssh timeout 5
ssh key-exchange group dh-group1-sha1
console timeout 0

dhcpd auto_config outside
!
dhcpd address 192.168.1.5-192.168.1.254 inside
dhcpd enable inside
!
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
group-policy GroupPolicy_96.80.240.49 internal
group-policy GroupPolicy_96.80.240.49 attributes
 vpn-tunnel-protocol ikev1 ikev2
dynamic-access-policy-record DfltAccessPolicy
tunnel-group 96.80.240.49 type ipsec-l2l
tunnel-group 96.80.240.49 general-attributes
 default-group-policy GroupPolicy_96.80.240.49
tunnel-group 96.80.240.49 ipsec-attributes
 ikev1 pre-shared-key *****
 ikev2 remote-authentication pre-shared-key *****
 ikev2 local-authentication pre-shared-key *****
!
class-map inspection_default
 match default-inspection-traffic
!
!
policy-map type inspect dns preset_dns_map
 parameters
  message-length maximum client auto
  message-length maximum 512
  no tcp-inspection
policy-map global_policy
 class inspection_default
  inspect dns preset_dns_map
  inspect ftp
  inspect h323 h225
  inspect h323 ras
  inspect rsh
  inspect rtsp
  inspect esmtp
  inspect sqlnet
  inspect skinny  
  inspect sunrpc
  inspect xdmcp
  inspect sip  
  inspect netbios
  inspect tftp
  inspect ip-options
!
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:66a255c63c3c1178cc10239d0c44cf72

I believe the changes you suggested were made.

I checked and the remote site has a dynamic crypto map for 10,0,0,99, but I am not sure it is associated with the VPN.

Interestingly when I changed the NAT rule as you suggested I got the same error, but when I changed the interface from inside to inside_1 The rule went through.

[Richard Burts]

I notice a couple of things that should be fixed in your config. You have this for the ACL used to identify traffic for encryption

access-list outside_cryptomap extended permit ip interface inside interface outside

it would be better to use an ACL like this

 access-list outside_cryptomap line 1 extended permit ip 192.168.1.0 255.255.255.0 172.30.0.0 255.255.255.0

Also I see nat translations for all traffic going outside and do not see anything that exempts the vpn traffic from translation.

It is good that you can successfully ping from your ASA to the peer. It should work from the outside interface and not necessarily from the inside interface. So that should be ok. It is somewhat concerning that the peer is not able to ping to the address of your ASA. What is the IP that your ASA has on its outside interface?

HTH

Rick

[joe@carmonnetwork.com]

I am able to ping the 96.80 address from my outside interface, but not from the inside.