Hi ttemir,Here you go: ASA#

thomasMung · ‎07-02-2014

Hello my friends,

I have been trying to establish VPN connectivity between IOS cisco router and ASA firewall over the internet - no luck so far. I think I am missing some important bit of the configuration.

Here are my configuration commands:

Router:

crypto isakmp policy 20
encryption 3des
auth pre-share
hash md5
group 2

crypto isakmp key XXX address 103.252.AAA.AAA

crypto ipsec transform-set 3DES-MD5 esp-3des esp-md5-hmac

crypto map MAP 5 ipsec-isakmp
set transform 3DES-MD5
match address VPN
set peer 103.252.AAA.AAA

ip access-list extended VPN
permit ip 10.110.25.0 0.0.0.255 10.10.0.0 0.0.255.255
permit icmp 10.110.25.0 0.0.0.255 10.10.0.0 0.0.255.255

ASA commands:

sysopt connection permit-vpn

crypto isakmp policy 10
authentication pre-share
encryption 3des
hash md5

tunnel-group 203.167.BBB.BBB type ipsec-l2l
tunnel-group 203.167.BBB.BBB ipsec-attributes
pre-shared-key XXX

access-list LIST permit ip 10.10.0.0 255.255.0.0 10.110.25.0 255.255.255.0

access-list LIST permit icmp 10.10.0.0 255.255.0.0 10.110.25.0 255.255.255.0

crypto ipsec transform-set 3DES-MD5 esp-3des esp-md5-hmac

crypto map VPN 10 set transform-set 3DES-MD5
crypto map VPN 10 match address LIST
crypto map VPN 10 set peer 203.167.BBB.BBB

crypto map VPN interface outside

Do you have any idea what is wrong? Thank you a lot in advance.

Tagir Temirgaliyev · ‎07-02-2014

where is router interface config?

and post from router and asa

sh cry isa sa

sh cry ips sa

thomasMung · ‎07-02-2014

Hi ttemir,

Here you go:

ASA# sh cry ips sa

There are no ipsec sas

RT01#sh cry ips sa | include 103.252
RT01#

(there is output for sh cry ips sa but not a single paragraph related to 103.252 VPN)

router interface:

interface GigabitEthernet0/1
description Internet
ip address 203.167.BBB.BBB 255.255.255.252
ip access-group outside_access_in in
no ip redirects
no ip unreachables
no ip proxy-arp
ip flow ingress
ip nat outside
ip virtual-reassembly in
no ip route-cache
duplex full
speed 100
no clns route-cache
crypto map MAP

ip access-list extended outside_access_in

permit esp host 103.252.AAA.AAA host 203.167.BBB.BBB
permit udp host 103.252.AAA.AAA host 203.167.BBB.BBB eq isakmp
permit udp host 103.252.AAA.AAA host 203.167.BBB.BBB range 1 65535
permit tcp host 103.252.AAA.AAA host 203.167.BBB.BBB range 1 65535
permit icmp host 103.252.AAA.AAA host 203.167.BBB.BBB

thank you!

bhnegi · ‎07-02-2014

Hi Thomas,

Have you excluded ipsec traffic from being getting Natted.

Best Regards,

Bheem

thomasMung · ‎07-02-2014

Hi Bhnegi,

Yes I did.

Also, when I am trying to enable ikev1 on the outside interface I am getting this error:

crypto ikev1 enable outside
ERROR: Unable to configure IKEv1 on interface 'outside' as ipsec-over-tcp is enabled on port 45, which is currently in use by another service. Please choose a different port for ipsec-over-tcp.

But from the show run i can see that it is enabled:

ASA# show run | include enable\ outside
crypto ikev2 enable outside client-services port 443
crypto ikev1 enable outside
enable outside

Thank you, I am stuck.

bhnegi · ‎07-02-2014

Are you using NAT on ASA? If yes please see workaround of bug below where

TCP Port 10000 was reserved as a fix of

CSCtl74435 VPN ports not removed from PAT pool

UDP Port 10000 was reserved as a fix of

CSCtn69941 VPN ports not removed from PAT pool (UDP cases)

Best Regards,

Bheem

thomasMung · ‎07-02-2014

Hi Bheem,

'Topic not found' when I try to open these links :-(

I am using NAT for normal internet access and no NAT for the VPN connectivity.

Does this bug mean that

crypto isakmp enable outside

is not enabled?

thomasMung · ‎07-02-2014

I managed to get this from the show crypto ipsec sa

     local crypto endpt.: 203.167.BBB.BBB, remote crypto endpt.: 103.252.AAA.AAA
     path mtu 1500, ip mtu 1500, ip mtu idb GigabitEthernet0/1
     current outbound spi: 0x0(0)
     PFS (Y/N): N, DH group: none

inbound esp sas:

inbound ah sas:

inbound pcp sas:

outbound esp sas:

outbound ah sas:

outbound pcp sas:

     local crypto endpt.: 203.167.BBB.BBB, remote crypto endpt.: 103.252.AAA.AAA
     path mtu 1500, ip mtu 1500, ip mtu idb GigabitEthernet0/1
     current outbound spi: 0x0(0)
     PFS (Y/N): N, DH group: none

And details from show crypto session detail

Interface: GigabitEthernet0/1
Session status: DOWN
Peer: 103.252.AAA.AAA port 500 fvrf: (none) ivrf: (none)
      Desc: (none)
      Phase1_id: (none)
IPSEC FLOW: permit 1 10.110.25.0/255.255.255.0 10.10.0.0/255.255.0.0
        Active SAs: 0, origin: crypto map
        Inbound: #pkts dec'ed 0 drop 0 life (KB/Sec) 0/0
        Outbound: #pkts enc'ed 0 drop 0 life (KB/Sec) 0/0

Tagir Temirgaliyev · ‎07-02-2014

http://www.cisco.com/c/en/us/support/docs/security/pix-500-series-security-appliances/9353-39.html

VPN between IOS and ASA