10-15-2012 12:09 PM
Here is my issue, with any luck someone can help...
I am using the Cisco client to establish a connection with a client. Once the connection is established I can no longer browse my local network. Below is the ipconfig results for both the local adapter and the VPN adapter.
Any help would be greatly appreciated.
Windows IP Configuration
Host Name . . . . . . . . . . . . : nvcadmin06
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Unknown
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No
Ethernet adapter Local Area Connection:
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Broadcom NetXtreme 57xx Gigabit Controller
Physical Address. . . . . . . . . : 00-18-8B-00-5C-B1
Dhcp Enabled. . . . . . . . . . . : No
IP Address. . . . . . . . . . . . : 10.20.0.5
Subnet Mask . . . . . . . . . . . : 255.0.0.0
Default Gateway . . . . . . . . . : 10.0.0.1
DNS Servers . . . . . . . . . . . : 10.0.0.1
208.67.222.222
Ethernet adapter Local Area Connection 2:
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Cisco Systems VPN Adapter
Physical Address. . . . . . . . . : 00-05-9A-3C-78-00
Dhcp Enabled. . . . . . . . . . . : No
IP Address. . . . . . . . . . . . : 10.10.10.197
Subnet Mask . . . . . . . . . . . : 255.0.0.0
Default Gateway . . . . . . . . . :
DNS Servers . . . . . . . . . . . : 192.168.2.19
Thank you in advance.
Solved! Go to Solution.
10-16-2012 05:39 AM
Hi Eric,
Unfortunately no, this is controlled by the VPN server.
You may try to change the routing on your machine with static routes, but this is not supported, since it is considered a security risk.
I would recommend to you to contact the remote administrator and explain that you need "split-tunneling" instead of "tunnelall".
Thanks.
Portu.
Please rate any helpful posts
10-16-2012 07:08 AM
Eric,
I appreciate your understanding.
Please mark this post as answered.
Have a nice day.
10-15-2012 01:38 PM
Hi Eric,
According to your output you are tunneling all the traffic across the tunnel, since there is no default-gateway defined under the VPN adapter stats.
Please check this out and let me know:
ASA 8.x : Allow Split Tunneling for AnyConnect VPN Client on the ASA Configuration Example
* This also applies for the Cisco IPsec VPN client.
I hope to help.
Portu.
Please rate any helpful posts
10-16-2012 05:09 AM
Thanks for the quick response. You are correct about all traffic going through the tunnel, and that is where I'm stuck. Unfortunately the vpn we are connecting to is a client of ours and we are unable to make any changes to their configuration. Are there any other options at this point?
Thanks!
10-16-2012 05:39 AM
Hi Eric,
Unfortunately no, this is controlled by the VPN server.
You may try to change the routing on your machine with static routes, but this is not supported, since it is considered a security risk.
I would recommend to you to contact the remote administrator and explain that you need "split-tunneling" instead of "tunnelall".
Thanks.
Portu.
Please rate any helpful posts
10-16-2012 06:15 AM
I thought you might say that. While not what I was hoping to hear, I certainly appreciate your help.
Thanks,
Eric
10-16-2012 07:08 AM
Eric,
I appreciate your understanding.
Please mark this post as answered.
Have a nice day.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide