Solved: Re: 2602i does not join 1852i / mobility express - Page 2

Sepp1 · ‎08-31-2018

Hi,

I'm trying to joing a AIR-CAP2602I-E-K9 to my 1852i with mobility express.

Regarding to https://www.cisco.com/c/en/us/td/docs/wireless/controller/technotes/8_4/b_cisco_mobility_express_8_4/b_Mobility_Express_Deployment_guide_chapter_0100.html

this should work as subordinate AP (table 2)

The 1852i says:

Unable to get Ap mode in Join request

Join request not accepted: Unsupported AP Model AIR-CAP2602I-E-K9

Join Request Process Failed: Unsupported ap model in join request from

Please can anyone help?

What am I'm missing?

The 1852i has fw 8.6.101.0

Thanks and kind regards

Sepp

Sepp1 · ‎09-07-2018

Did not work, still the same. I added the "primary-base" again but still no luck.

Maybe it has something todo with incorrect time/timezone?

My 1852i is one hour late.

BUT if I try to set time on the ap, it does not last:

APe00e.daf8.7bec#clock set 12:04:00 Sep 7 2018
APe00e.daf8.7bec#
*Sep 7 12:04:00.000: %SYS-6-CLOCKUPDATE: System clock has been updated from 11:04:12 UTC Fri Sep 7 2018 to 12:04:00 UTC Fri Sep 7 2018, configured from console by Cisco on console.

Sep 7 12:04:25.735: AP has SHA2 MIC certificate - Using SHA2 MIC certificate for DTLS.

Sep 7 11:04:03.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.30.3.238 peer_port: 5246
Sep 7 11:04:03.251: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 172.30.3.238 peer_port: 5246
Sep 7 11:04:03.255: %CAPWAP-5-SENDJOIN: sending Join Request to 172.30.3.238
Sep 7 11:04:08.255: %CAPWAP-5-SENDJOIN: sending Join Request to 172.30.3.238

I do not know either how to set timezone on the ap. "clock timezone" is a non valid command, therefore I adjusted to GMT alreade an the 1852i

Sepp1 · ‎09-07-2018

Maybe another hint:

show ap join stats detailed <MacAddr>

...

- Reason for last unsuccessful join attempt................ Join failed as dtls connection not found

...

Leo Laohoo · ‎09-07-2018

@Sepp1 wrote:

Maybe it has something todo with incorrect time/timezone?

Where is the ME getting it's time and date from? I'd recommend configuring NTP on the ME. When the AP searches for the ME, the ME will push the correct time and date down.

Sepp1 · ‎09-07-2018

Actually I was using NTP, with timezone set to GMT +1
Then I saw, that the AP does not get the correct timezone (it has UTC). So I adjusted the 1852 as well to GMT.
If you look at the debug out, you can see that the AP gets a new timestamp. This is not the shown time on the controller (1 hour early)

Leo Laohoo · ‎09-07-2018

Don't worry about what the time is on the AP: The controller will push that info down.
Can you try a different firmware? Like the latest 8.3?

Sepp1 · ‎09-07-2018

Ok. I downgraded the 1852i know to 8.3.143 (by installing the appropriate "ap1g4"-file through web-console)
It is up and running and my second 1852i joined as well.
I restarted my 2602i:
It still does not join.
----------
1852_Capwap error debug:
*spamApTask0: Sep 07 16:13:44.513: 00:56:2b:00:73:b0 ApModel: AIR-CAP2602I-E-K9
*spamApTask0: Sep 07 16:13:44.513: 00:56:2b:00:73:b0 Could not find image version of bundled AP(apType: 27)!!!
*spamApTask0: Sep 07 16:13:44.513: 00:56:2b:00:73:b0 Unable to get AP Bundled Version. Using Controller Version!!!
*spamApTask0: Sep 07 16:13:54.771: 00:56:2b:00:73:b0 Unable to get Ap mode in Join request
*spamApTask0: Sep 07 16:13:54.772: 00:56:2b:00:73:b0 State machine handler: Failed to process msg type = 3 state = 0 from 172.30.3.246:51134
*spamApTask0: Sep 07 16:13:54.772: 00:56:2b:00:73:b0 Failed to parse CAPWAP packet from 172.30.3.246:51134
*spamApTask0: Sep 07 16:13:59.769: 00:56:2b:00:73:b0 Multiple Join Request: Join request received from AP which is already present. Deleting previous conne
*spamApTask0: Sep 07 16:13:59.769: 00:56:2b:00:73:b0 Not sending DTLS session closed notification to capwap.(172.30.3.246:51134)
*spamApTask0: Sep 07 16:13:59.770: 00:56:2b:00:73:b0 State machine handler: Failed to process msg type = 3 state = 0 from 172.30.3.246:51134
*spamApTask0: Sep 07 16:13:59.770: 00:56:2b:00:73:b0 Failed to parse CAPWAP packet from 172.30.3.246:51134
*spamApTask0: Sep 07 16:13:59.771: 00:00:00:00:00:00 Discarding non-ClientHello Handshake OR DTLS encrypted packet from 172.30.3.246:51134)since DTLS session is not established
*spamApTask0: Sep 07 16:14:00.028: 00:56:2b:00:73:b0 Unable to get Ap mode in Join request
----------------
My 1852 says (show ap join states detailed )
"reached limit for maximum number of Aps on Interface"
I just have two 1852i and the not joining 2602
"show run-config" tells me I could connect 25 Aps (it was 50 on the firmware)

Leo Laohoo · ‎09-07-2018

This is getting into my nerves ... A few more tricks ...
debug capwap console cli
del /f /r flash:flash:/ap3g2-k9w8-mx.153-3.JF8/
reboot

Sepp1 · ‎09-10-2018

Ok. Flashfile deleted. Now it does not boot at all:

Xmodem file system is available.
flashfs[0]: 11 files, 2 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 31997952
flashfs[0]: Bytes used: 457728
flashfs[0]: Bytes available: 31540224
flashfs[0]: flashfs fsck took 14 seconds.
Reading cookie from SEEPROM
Base Ethernet MAC address: e0:0e:da:f8:7b:ec
Ethernet speed is 100 Mb - FULL Duplex
Loading "flash:/ap3g2-k9w8-mx.153-3.JF8/ap3g2-k9w8-mx.153-3.JF8"...flash:/ap3g2-k9w8-mx.153-3.JF8/ap3g2-k9w8-mx.153-3.JF8: no such file or directory
Error loading "flash:/ap3g2-k9w8-mx.153-3.JF8/ap3g2-k9w8-mx.153-3.JF8"
Interrupt within 5 seconds to abort boot process.
Boot process failed...
The system is unable to boot automatically. The BOOT
environment variable needs to be set to a bootable
image.
C2600 Boot Loader (AP3G2-BOOT-M) LoaderVersion 12.4(25e)JAY, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Compiled Thu 03-Oct-13 03:35 by sdcunha
ap:

Leo Laohoo · ‎09-10-2018

Post the complete output to the command "dir flash:".

Sepp1 · ‎09-10-2018

ap: dir flash:
Directory of flash:/
2 -rwx 287 info
3 -rwx 4 FOC2027576Y
4 -rwx 1915 private-config
5 -rwx 7192 private-multiple-fs
38 drwx 0 configs
39 -rwx 64 sensord_CSPRNG0
40 -rwx 2811 config.txt
41 -rwx 64 sensord_CSPRNG1
42 -rwx 87164 event.log
8 -rwx 267 capwap-saved-config
7 -rwx 428 env_vars
47 -rwx 352747 crashinfo_19930803-031023-UTC
31540224 bytes available (457728 bytes used)
ap:

Leo Laohoo · ‎09-10-2018

Hmmmm ... Some deleted the RCV sub-directory.

First, go HERE and download the "RCV" file (TAR).

Next, to load the RCV file into the AP via console, go HERE and scroll down to Step 4.

Sepp1 · ‎09-10-2018

Did it. Does still not work 😞
------------------------------------------------

Complete boot of the 2602:
IOS Bootloader - Starting system.
flash is writable
FLASH CHIP: Numonyx Mirrorbit (0089)
Xmodem file system is available.
flashfs[0]: sector 91, block 4 checksum (0x0 != 0xe2f0)
flashfs[0]: 20 files, 3 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 31997952
flashfs[0]: Bytes used: 7940608
flashfs[0]: Bytes available: 24057344
flashfs[0]: flashfs fsck took 16 seconds.
Reading cookie from SEEPROM
Base Ethernet MAC address: e0:0e:da:f8:7b:ec
Ethernet speed is 100 Mb - FULL Duplex
Loading "flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-mx"...#########################

File "flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-mx" uncompressed and installed, entry point: 0x2003000
executing...

Secondary Bootloader - Starting system.
Tide MB - 32MB of flash
Xmodem file system is available.
flashfs[0]: 20 files, 3 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 31997952
flashfs[0]: Bytes used: 7941120
flashfs[0]: Bytes available: 24056832
flashfs[0]: flashfs fsck took 8 seconds.
flashfs[1]: 0 files, 1 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 12257280
flashfs[1]: Bytes used: 1024
flashfs[1]: Bytes available: 12256256
flashfs[1]: flashfs fsck took 1 seconds.
Base Ethernet MAC address: e0:0e:da:f8:7b:ec

2600/3600 AP, PID: 'AIR-CAP2602I-E-K9 '. Checking for BL upgrade...
BL: C2600 Boot Loader (AP3G2-BOOT-M) LoaderVersion 12.4(25e)JAY, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Compiled Thu 03-Oct-13 03:35 by sdcunha

BL Build year: 13
Unable to locate IOS image with name **xx**.
Boot CMD: 'boot flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-xx'
Loading "flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-xx"...#############################
File "flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-xx" uncompressed and installed, entry point: 0x1003000
executing...

Restricted Rights Legend

Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706

Cisco IOS Software, C2600 Software (AP3G2-RCVK9W8-M), Version 15.3(3)JF8, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2018 by Cisco Systems, Inc.
Compiled Fri 20-Jul-18 21:14 by prod_rel_team

Tide MB - 32MB of flash
Initializing flashfs...

flashfs[2]: 20 files, 3 directories
flashfs[2]: 0 orphaned files, 0 orphaned directories
flashfs[2]: Total bytes: 31739904
flashfs[2]: Bytes used: 7941120
flashfs[2]: Bytes available: 23798784
flashfs[2]: flashfs fsck took 9 seconds.
flashfs[2]: Initialization complete.
flashfs[3]: 0 files, 1 directories
flashfs[3]: 0 orphaned files, 0 orphaned directories
flashfs[3]: Total bytes: 11999232
flashfs[3]: Bytes used: 1024
flashfs[3]: Bytes available: 11998208
flashfs[3]: flashfs fsck took 1 seconds.
flashfs[3]: Initialization complete....done Initializing flashfs.
PRST-VBL Debug set from cache (0x3FF,3FF) to All
PRST-VBL API Get (,3640298,280,0xC-NMVL-?)
PRST-VBL DET Lock - ok
PRST-VBL DET Compare Next - YES > prst-dbg=0x3FF
PRST-VBL DET Cache unlock - ok
PRST-VBL API Get - ok returning "prst-dbg=0x3FF" of size 15
PRST-VBL API Get (prst-dbg=0x3FF,3640298,280,0xC-NMVL-?)
PRST-VBL DET Lock - ok
PRST-VBL DET Compare Next - NO prst-dbg=0x3FF <= prst-dbg=0x3FF
PRST-VBL DET Compare Next - YES prst-dbg=0x3FF > prst-fls=2
PRST-VBL DET Cache unlock - ok
PRST-VBL API Get - ok returning "prst-fls=2" of size 11
PRST-VBL API Get (prst-fls=2,3640298,280,0xC-NMVL-?)
PRST-VBL DET Lock - ok
PRST-VBL DET Compare Next - NO prst-fls=2 <= prst-dbg=0x3FF
PRST-VBL DET Compare Next - NO prst-fls=2 <= prst-fls=2
PRST-VBL DET Compare Next - YES prst-fls=2 > prst-ver=1
PRST-VBL DET Cache unlock - ok
PRST-VBL API Get - ok returning "prst-ver=1" of size 11
PRST-VBL API Get (prst-ver=1,3640298,280,0xC-NMVL-?)
PRST-VBL DET Lock - ok
PRST-VBL DET Compare Next - NO prst-ver=1 <= prst-dbg=0x3FF
PRST-VBL DET Compare Next - NO prst-ver=1 <= prst-fls=2
PRST-VBL DET Compare Next - NO prst-ver=1 <= prst-ver=1
PRST-VBL DET Cache unlock - ok
PRST-VBL API Get - prst-ver=1 missing in the prst cache
PRST-VBL STD Init cache - ok
PRST-VBL MED Init complete - filesys added: tmpsys
PRST-VBL MED Init complete - filesys added: tftp
PRST-VBL MED Init complete - filesys added: null
PRST-VBL MED Init complete - filesys added: lwapp
PRST-VBL MED Init complete - filesys added: capwap
PRST-VBL STD Process - waiting on system init
PRST-VBL MED Init complete - filesys added: rcp
PRST-VBL MED Init complete - filesys added: scp
PRST-VBL API Get (snmpboots,3EF2E80,11,0x0-DEFAULT)
PRST-VBL DET Lock - ok
PRST-VBL DET Cache unlock - ok
PRST-VBL API Get - snmpboots missing in the prst cache
PRST-VBL MED Init complete - filesys added: http
PRST-VBL MED Init complete - filesys added: tar

This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
[email protected].

PRST-VBL MED Init complete - filesys added: https
PRST-VBL MED Init complete - filesys added: cns
cisco AIR-CAP2602I-E-K9 (PowerPC) processor (revision A0) with 188398K/60928K bytes of memory.
Processor board ID FCW2029NCYJ
PowerPC CPU at 800Mhz, revision number 0x2151
Last reset from power-on
LWAPP image version 8.5.135.0
1 Gigabit Ethernet interface

32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: E0:0E:DA:F8:7B:EC
Part Number : 73-14588-03
PCB Serial Number : FOC2027576Y
Top Assembly Part Number : 800-102026-02
Top Assembly Serial Number : FCW2029NCYJ
Top Revision Number : A0
Product/Model Number : AIR-CAP2602I-E-K9
% Please define a domain-name first.
Translating "CISCO-CAPWAP-CONTROLLER.gast-wlan"...domain server (255.255.255.255)

Press RETURN to get started!

*Mar 1 00:00:11.495: PRST-VBL Debug set from cache (0x3FF,3FF) to All
*Mar 1 00:00:11.547: PRST-VBL API Get (,3640298,280,0xC-NMVL-?)
*Mar 1 00:00:11.575: PRST-VBL DET Lock - ok
*Mar 1 00:00:11.631: PRST-VBL DET Compare Next - YES > prst-dbg=0x3FF
*Mar 1 00:00:11.671: PRST-VBL DET Cache unlock - ok
*Mar 1 00:00:11.739: PRST-VBL API Get - ok returning "prst-dbg=0x3FF" of size 15
*Mar 1 00:00:11.807: PRST-VBL API Get (prst-dbg=0x3FF,3640298,280,0xC-NMVL-?)
*Mar 1 00:00:11.835: PRST-VBL DET Lock - ok
*Mar 1 00:00:11.907: PRST-VBL DET Compare Next - NO prst-dbg=0x3FF <= prst-dbg=0x3FF
*Mar 1 00:00:11.979: PRST-VBL DET Compare Next - YES prst-dbg=0x3FF > prst-fls=2
*Mar 1 00:00:12.015: PRST-VBL DET Cache unlock - ok
*Mar 1 00:00:12.083: PRST-VBL API Get - ok returning "prst-fls=2" of size 11
*Mar 1 00:00:12.143: PRST-VBL API Get (prst-fls=2,3640298,280,0xC-NMVL-?)
*Mar 1 00:00:12.171: PRST-VBL DET Lock - ok
*Mar 1 00:00:12.243: PRST-VBL DET Compare Next - NO prst-fls=2 <= prst-dbg=0x3FF
*Mar 1 00:00:12.307: PRST-VBL DET Compare Next - NO prst-fls=2 <= prst-fls=2
*Mar 1 00:00:12.371: PRST-VBL DET Compare Next - YES prst-fls=2 > prst-ver=1
*Mar 1 00:00:12.411: PRST-VBL DET Cache unlock - ok
*Mar 1 00:00:12.475: PRST-VBL API Get - ok returning "prst-ver=1" of size 11
*Mar 1 00:00:12.539: PRST-VBL API Get (prst-ver=1,3640298,280,0xC-NMVL-?)
*Mar 1 00:00:12.567: PRST-VBL DET Lock - ok
*Mar 1 00:00:12.635: PRST-VBL DET Compare Next - NO prst-ver=1 <= prst-dbg=0x3FF
*Mar 1 00:00:12.703: PRST-VBL DET Compare Next - NO prst-ver=1 <= prst-fls=2
*Mar 1 00:00:12.767: PRST-VBL DET Compare Next - NO prst-ver=1 <= prst-ver=1
*Mar 1 00:00:12.803: PRST-VBL DET Cache unlock - ok
*Mar 1 00:00:12.871: PRST-VBL API Get - prst-ver=1 missing in the prst cache
*Mar 1 00:00:12.903: PRST-VBL STD Init cache - ok
*Mar 1 00:00:12.963: PRST-VBL MED Init complete - filesys added: tmpsys
*Mar 1 00:00:13.023: PRST-VBL MED Init complete - filesys added: tftp
*Mar 1 00:00:13.079: PRST-VBL MED Init complete - filesys added: null
*Mar 1 00:00:13.139: PRST-VBL MED Init complete - filesys added: lwapp
*Mar 1 00:00:13.199: PRST-VBL MED Init complete - filesys added: capwap
*Mar 1 00:00:13.255: PRST-VBL STD Process - waiting on system init
*Mar 1 00:00:13.635: %LWAPP-3-CLIENTERRORLOG: Load nvram:/lwapp_ap.cfg config failed, trying backup...
*Mar 1 00:00:13.635: %LWAPP-3-CLIENTERRORLOG: Load nvram:/lwapp_ap.cfg.bak config failed...
*Mar 1 00:00:13.691: PRST-VBL MED Init complete - filesys added: rcp
*Mar 1 00:00:13.767: PRST-VBL MED Init complete - filesys added: scp
*Mar 1 00:00:13.839: PRST-VBL API Get (snmpboots,3EF2E80,11,0x0-DEFAULT)
*Mar 1 00:00:13.867: PRST-VBL DET Lock - ok
*Mar 1 00:00:13.903: PRST-VBL DET Cache unlock - ok
*Mar 1 00:00:13.967: PRST-VBL API Get - snmpboots missing in the prst cache
*Mar 1 00:00:14.027: PRST-VBL MED Init complete - filesys added: http
*Mar 1 00:00:14.083: PRST-VBL MED Init complete - filesys added: tar
*Mar 1 00:00:14.087: SCHED: Ethernet Bridge Process: install watched boolean System Initialized(3EDF2A0), os:1 ah:0
*Mar 1 00:00:14.331: Found crash file: 'crashinfo_19930803-031023-UTC'
*Mar 1 00:00:15.287: PRST-VBL MED Init complete - filesys added: https
*Mar 1 00:00:15.355: PRST-VBL MED Init complete - filesys added: cns
*Mar 1 00:00:15.463: %LWAPP-4-CLIENTEVENTLOG: PnP waiting for capwap init
*Mar 1 00:00:15.463: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:16.299: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C2600 Software (AP3G2-RCVK9W8-M), Version 15.3(3)JF8, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2018 by Cisco Systems, Inc.
Compiled Fri 20-Jul-18 21:14 by prod_rel_team
*Mar 1 00:00:16.299: %SNMP-5-COLDSTART: SNMP agent on host APe00e.daf8.7bec is undergoing a cold start
*Mar 1 00:00:16.319: PRST-VBL STD Process - running but no timer started
*Mar 1 00:00:16.359: SCHED: Ethernet Bridge Process: remove watched boolean System Initialized(3EDF2A0)
*Mar 1 00:00:16.359: SCHED: Ethernet Bridge Process: install watched queue Soap BVI input queue(3ED2CE0), os:0 ah:0
*Mar 1 00:00:17.359: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
*Mar 1 00:00:21.007: DPAA Initialization Complete
*Mar 1 00:00:21.007: %SYS-3-HARIKARI: Process DPAA INIT top-level routine exited
*Mar 1 00:00:22.007: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:24.007: %LINK-6-UPDOWN: Interface BVI1, changed state to down
*Mar 1 00:00:25.007: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to down
*Mar 1 00:00:28.363: %LINK-6-UPDOWN: Interface BVI1, changed state to up
*Mar 1 00:00:29.363: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
*Mar 1 00:00:35.355: %LWAPP-3-CLIENTERRORLOG: rcb in dcb is NULL
*Mar 1 00:00:35.355: -Traceback= 11B6980z 17614D8z 1788FC8z 133FBF4z 132697Cz

*Mar 1 00:00:37.455: %CAPWAP-5-AP_EASYADMIN_INFO: AP Easy Admin information - apEasyAdminConfig: there is no full image exists, continue anyway!

*Mar 1 00:00:37.455: %CAPWAP-5-AP_EASYADMIN_INFO: AP Easy Admin information - Easy Admin is not enabled, turn it off!

*Mar 1 00:00:37.463: %LWAPP-3-CLIENTERRORLOG: NumOfSlots Mismatch Reinit all Radios config rcb:0 Cfg:2
*Mar 1 00:00:37.599: %SSH-5-ENABLED: SSH 2.0 has been enabledlwapp_crypto_init: MIC Present and Parsed Successfully

*Mar 1 00:00:37.623: %CAPWAP-3-EVENTLOG: Config Present. PNP Not required
*Mar 1 00:00:37.623: Cert ISSUER (39): cn=Cisco Manufacturing CA SHA2,o=Cisco

*Mar 1 00:00:41.363: %CDP_PD-4-POWER_OK: All radios disabled - LOW_POWER_CLASSIC_NO_INJECTOR_CONFIGURED inline power sourcecreating PnP template view

Translating "CISCO-CAPWAP-CONTROLLER.gast-wlan"...domain server (255.255.255.255)

*Mar 1 00:01:26.707: AP has SHA2 MIC certificate - Using SHA2 MIC certificate for DTLS.

*Sep 10 11:50:09.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.30.3.238 peer_port: 5246
*Sep 10 11:50:09.255: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 172.30.3.238 peer_port: 5246
*Sep 10 11:50:09.255: %CAPWAP-5-SENDJOIN: sending Join Request to 172.30.3.238
*Sep 10 11:50:14.255: %CAPWAP-5-SENDJOIN: sending Join Request to 172.30.3.238
*Sep 10 11:50:14.259: %DTLS-5-ALERT: Received WARNING : Close notify alert from 172.30.3.238
*Sep 10 11:50:14.259: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 172.30.3.238:5246
*Sep 10 11:50:14.259: AP has SHA2 MIC certificate - Using SHA2 MIC certificate for DTLS.

*Sep 10 11:50:32.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.30.3.238 peer_port: 5246
*Sep 10 11:50:32.251: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 172.30.3.238 peer_port: 5246
*Sep 10 11:50:32.251: %CAPWAP-5-SENDJOIN: sending Join Request to 172.30.3.238
*Sep 10 11:50:37.251: %CAPWAP-5-SENDJOIN: sending Join Request to 172.30.3.238
*Sep 10 11:50:37.251: %DTLS-5-ALERT: Received WARNING : Close notify alert from 172.30.3.238
*Sep 10 11:50:37.251: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 172.30.3.238:5246
*Sep 10 11:50:37.251: AP has SHA2 MIC certificate - Using SHA2 MIC certificate for DTLS.

*Sep 10 11:50:37.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.30.3.238 peer_port: 5246
*Sep 10 11:50:37.255: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 172.30.3.238 peer_port: 5246
*Sep 10 11:50:37.255: %CAPWAP-5-SENDJOIN: sending Join Request to 172.30.3.238
-------------------------------------------------------------------------------

1852 capwap debug-output

-------------------------------------------------------------------------------
*spamApTask0: Sep 10 13:49:59.611: e0:0e:da:f8:7b:ec Discovery Request from 172.30.3.246:51135

*spamApTask0: Sep 10 13:49:59.611: e0:0e:da:f8:7b:ec ApModel: AIR-CAP2602I-E-K9

*spamApTask0: Sep 10 13:49:59.611: e0:0e:da:f8:7b:ec Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 25, MaxLicense=25 joined Aps =2
*spamApTask0: Sep 10 13:49:59.611: e0:0e:da:f8:7b:ec apType = 27 apModel: AIR-CAP2602I-E-K9

*spamApTask0: Sep 10 13:49:59.611: e0:0e:da:f8:7b:ec apType: Ox1b bundleApImageVer:
*spamApTask0: Sep 10 13:49:59.611: e0:0e:da:f8:7b:ec Could not find image version of bundled AP(apType: 27)!!!
*spamApTask0: Sep 10 13:49:59.611: e0:0e:da:f8:7b:ec Unable to get AP Bundled Version. Using Controller Version!!!

*spamApTask0: Sep 10 13:49:59.611: e0:0e:da:f8:7b:ec Discovery Response sent to 172.30.3.246:51135

*spamApTask0: Sep 10 13:50:05.333: 00:38:df:1b:dc:20 WTP Event Request from 172.30.2.51:5256 epoch 1536580205

*spamApTask0: Sep 10 13:50:05.334: 00:38:df:1b:dc:20 WTP Event Response sent to 172.30.2.51:5256

*spamApTask0: Sep 10 13:50:05.335: 00:38:df:1b:dc:20 WTP Event Request from 172.30.2.51:5256 epoch 1536580205

*spamApTask0: Sep 10 13:50:05.335: 00:38:df:1b:dc:20 WTP Event Response sent to 172.30.2.51:5256

*spamApTask0: Sep 10 13:50:10.704: 00:72:78:19:76:a0 Echo Request from 172.30.2.93:5272

*spamApTask0: Sep 10 13:50:10.705: 00:72:78:19:76:a0 Echo Response sent to 172.30.2.93:5272

*spamApTask0: Sep 10 13:50:17.611: e0:0e:da:f8:7b:ec Discovery Request from 172.30.3.246:51135

*spamApTask0: Sep 10 13:50:17.611: e0:0e:da:f8:7b:ec ApModel: AIR-CAP2602I-E-K9

*spamApTask0: Sep 10 13:50:17.611: e0:0e:da:f8:7b:ec Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 25, MaxLicense=25 joined Aps =2
*spamApTask0: Sep 10 13:50:17.611: e0:0e:da:f8:7b:ec apType = 27 apModel: AIR-CAP2602I-E-K9

*spamApTask0: Sep 10 13:50:17.611: e0:0e:da:f8:7b:ec apType: Ox1b bundleApImageVer:
*spamApTask0: Sep 10 13:50:17.611: e0:0e:da:f8:7b:ec Could not find image version of bundled AP(apType: 27)!!!
*spamApTask0: Sep 10 13:50:17.611: e0:0e:da:f8:7b:ec Unable to get AP Bundled Version. Using Controller Version!!!

*spamApTask0: Sep 10 13:50:17.611: e0:0e:da:f8:7b:ec Discovery Response sent to 172.30.3.246:51135

*spamApTask0: Sep 10 13:50:17.611: e0:0e:da:f8:7b:ec Discovery Request from 172.30.3.246:51135

*spamApTask0: Sep 10 13:50:17.611: e0:0e:da:f8:7b:ec ApModel: AIR-CAP2602I-E-K9

*spamApTask0: Sep 10 13:50:17.611: e0:0e:da:f8:7b:ec Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 25, MaxLicense=25 joined Aps =2
*spamApTask0: Sep 10 13:50:17.611: e0:0e:da:f8:7b:ec apType = 27 apModel: AIR-CAP2602I-E-K9

*spamApTask0: Sep 10 13:50:17.612: e0:0e:da:f8:7b:ec apType: Ox1b bundleApImageVer:
*spamApTask0: Sep 10 13:50:17.612: e0:0e:da:f8:7b:ec Could not find image version of bundled AP(apType: 27)!!!
*spamApTask0: Sep 10 13:50:17.612: e0:0e:da:f8:7b:ec Unable to get AP Bundled Version. Using Controller Version!!!

*spamApTask0: Sep 10 13:50:17.612: e0:0e:da:f8:7b:ec Discovery Response sent to 172.30.3.246:51135

*spamApTask0: Sep 10 13:50:17.612: e0:0e:da:f8:7b:ec Discovery Request from 172.30.3.246:51135

*spamApTask0: Sep 10 13:50:17.612: e0:0e:da:f8:7b:ec ApModel: AIR-CAP2602I-E-K9

*spamApTask0: Sep 10 13:50:17.612: e0:0e:da:f8:7b:ec Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 25, MaxLicense=25 joined Aps =2
*spamApTask0: Sep 10 13:50:17.612: e0:0e:da:f8:7b:ec apType = 27 apModel: AIR-CAP2602I-E-K9

*spamApTask0: Sep 10 13:50:17.612: e0:0e:da:f8:7b:ec apType: Ox1b bundleApImageVer:
*spamApTask0: Sep 10 13:50:17.612: e0:0e:da:f8:7b:ec Could not find image version of bundled AP(apType: 27)!!!
*spamApTask0: Sep 10 13:50:17.612: e0:0e:da:f8:7b:ec Unable to get AP Bundled Version. Using Controller Version!!!

*spamApTask0: Sep 10 13:50:17.612: e0:0e:da:f8:7b:ec Discovery Response sent to 172.30.3.246:51135

*spamApTask0: Sep 10 13:50:26.697: 00:38:df:1b:dc:20 WTP Event Request from 172.30.2.51:5256 epoch 1536580226

*spamApTask0: Sep 10 13:50:26.697: 00:38:df:1b:dc:20 WTP Event Response sent to 172.30.2.51:5256

*spamApTask0: Sep 10 13:50:26.719: 00:38:df:1b:dc:20 WTP Event Request from 172.30.2.51:5256 epoch 1536580226

*spamApTask0: Sep 10 13:50:26.720: 00:38:df:1b:dc:20 WTP Event Response sent to 172.30.2.51:5256

*spamApTask0: Sep 10 13:50:26.721: 00:38:df:1b:dc:20 WTP Event Request from 172.30.2.51:5256 epoch 1536580226

*spamApTask0: Sep 10 13:50:26.721: 00:38:df:1b:dc:20 WTP Event Response sent to 172.30.2.51:5256

*spamApTask0: Sep 10 13:50:26.723: 00:38:df:1b:dc:20 WTP Event Request from 172.30.2.51:5256 epoch 1536580226

*spamApTask0: Sep 10 13:50:26.723: 00:38:df:1b:dc:20 WTP Event Response sent to 172.30.2.51:5256

*spamApTask0: Sep 10 13:50:27.610: 00:00:00:00:00:00 DTLS connection not found, creating new connection for 172.30.3.246 (51135) 172.30.3.238 (5 246)

*spamApTask0: Sep 10 13:50:27.865: 00:00:00:00:00:00 DTLS Session established server (172.30.3.238:5246), client (172.30.3.246:51135)
*spamApTask0: Sep 10 13:50:27.865: 00:00:00:00:00:00 Starting wait join timer for AP: 172.30.3.246:51135

*spamApTask0: Sep 10 13:50:27.868: e0:0e:da:f8:7b:ec Join Request from 172.30.3.246:51135

*spamApTask0: Sep 10 13:50:27.868: e0:0e:da:f8:7b:ec Unable to get Ap mode in Join request

*spamApTask0: Sep 10 13:50:27.868: e0:0e:da:f8:7b:ec Allocate database entry for AP 172.30.3.246:51135, already allocated index 65535

*spamApTask0: Sep 10 13:50:27.868: e0:0e:da:f8:7b:ec AP Allocate request at index ffff
*spamApTask0: Sep 10 13:50:27.869: 00:00:00:00:00:00 Deleting AP entry 172.30.3.246:51135 from temporary database.
*spamApTask0: Sep 10 13:50:27.869: e0:0e:da:f8:7b:ec AP with same name APe00e.daf8.7bec exist. Using default name APe00e.daf8.7bec for this AP. radId 21 dupRadId 21dupApMac: E0:0E:DA:F8:7B:EC

*spamApTask0: Sep 10 13:50:27.869: e0:0e:da:f8:7b:ec Dropping request or response packet to AP :172.30.3.246 (51135) by Controller: 172.30.3.23 8 (5246), message Capwap_wtp_event_response, state Capwap_no_state

*spamApTask0: Sep 10 13:50:27.869: e0:0e:da:f8:7b:ec Message type Capwap_wtp_event_response is not allowed to send in state Capwap_no_state for AP 172.30.3.246

*spamApTask0: Sep 10 13:50:27.869: e0:0e:da:f8:7b:ec Join Request failed!

*spamApTask0: Sep 10 13:50:27.869: e0:0e:da:f8:7b:ec State machine handler: Failed to process msg type = 3 state = 0 from 172.30.3.246:51135

*spamApTask0: Sep 10 13:50:27.869: e0:0e:da:f8:7b:ec Failed to parse CAPWAP packet from 172.30.3.246:51135

*spamApTask0: Sep 10 13:50:32.867: e0:0e:da:f8:7b:ec Join Request from 172.30.3.246:51135

*spamApTask0: Sep 10 13:50:32.867: e0:0e:da:f8:7b:ec Join request received from AP which is already present. Deleting previous connection
172.30. 3.246:51135

*spamApTask0: Sep 10 13:50:32.867: e0:0e:da:f8:7b:ec Multiple Join Request: Join request received from AP which is already present. Deleting pre vious conne
*spamApTask0: Sep 10 13:50:32.867: e0:0e:da:f8:7b:ec Finding DTLS connection to delete for AP (172:30:3:246/51135)
*spamApTask0: Sep 10 13:50:32.867: e0:0e:da:f8:7b:ec Disconnecting DTLS Capwap-Ctrl session 0x6a83b70 for AP (172:30:3:246/51135). Notify(false)
*spamApTask0: Sep 10 13:50:32.867: e0:0e:da:f8:7b:ec CAPWAP State: Dtls tear down

*spamApTask0: Sep 10 13:50:32.867: e0:0e:da:f8:7b:ec Not sending DTLS session closed notification to capwap.(172.30.3.246:51135)
*spamApTask0: Sep 10 13:50:32.868: e0:0e:da:f8:7b:ec AP Delete request
*spamApTask0: Sep 10 13:50:32.868: e0:0e:da:f8:7b:ec DTLS connection not found. Ignoring join request from 172.30.3.246:51135

*spamApTask0: Sep 10 13:50:32.868: e0:0e:da:f8:7b:ec Join Request failed!

*spamApTask0: Sep 10 13:50:32.868: e0:0e:da:f8:7b:ec State machine handler: Failed to process msg type = 3 state = 0 from 172.30.3.246:51135

*spamApTask0: Sep 10 13:50:32.868: e0:0e:da:f8:7b:ec Failed to parse CAPWAP packet from 172.30.3.246:51135

*spamApTask0: Sep 10 13:50:32.870: 00:00:00:00:00:00 Discarding non-ClientHello Handshake OR DTLS encrypted packet from 172.30.3.246:51135)sinc e DTLS session is not established

*spamApTask0: Sep 10 13:50:32.870: 00:00:00:00:00:00 DTLS connection not found, creating new connection for 172.30.3.246 (51135) 172.30.3.238 (5 246)

*spamApTask0: Sep 10 13:50:33.123: 00:00:00:00:00:00 DTLS Session established server (172.30.3.238:5246), client (172.30.3.246:51135)
*spamApTask0: Sep 10 13:50:33.123: 00:00:00:00:00:00 Starting wait join timer for AP: 172.30.3.246:51135

*spamApTask0: Sep 10 13:50:33.126: e0:0e:da:f8:7b:ec Join Request from 172.30.3.246:51135

*spamApTask0: Sep 10 13:50:33.126: e0:0e:da:f8:7b:ec Unable to get Ap mode in Join request

*spamApTask0: Sep 10 13:50:33.126: e0:0e:da:f8:7b:ec Allocate database entry for AP 172.30.3.246:51135, already allocated index 65535

*spamApTask0: Sep 10 13:50:33.126: e0:0e:da:f8:7b:ec AP Allocate request at index ffff
*spamApTask0: Sep 10 13:50:33.127: 00:00:00:00:00:00 Deleting AP entry 172.30.3.246:51135 from temporary database.
*spamApTask0: Sep 10 13:50:33.127: e0:0e:da:f8:7b:ec AP with same name APe00e.daf8.7bec exist. Using default name APe00e.daf8.7bec for this AP. radId 22 dupRadId 22dupApMac: E0:0E:DA:F8:7B:EC

*spamApTask0: Sep 10 13:50:33.127: e0:0e:da:f8:7b:ec Dropping request or response packet to AP :172.30.3.246 (51135) by Controller: 172.30.3.23 8 (5246), message Capwap_wtp_event_response, state Capwap_no_state

*spamApTask0: Sep 10 13:50:33.127: e0:0e:da:f8:7b:ec Message type Capwap_wtp_event_response is not allowed to send in state Capwap_no_state for AP 172.30.3.246

*spamApTask0: Sep 10 13:50:33.127: e0:0e:da:f8:7b:ec Join Request failed!

*spamApTask0: Sep 10 13:50:33.127: e0:0e:da:f8:7b:ec Failed to parse CAPWAP packet from 172.30.3.246:51135

*spamApTask0: Sep 10 13:50:37.367: 00:72:78:19:76:a0 WTP Event Request from 172.30.2.93:5272 epoch 1536580237

*spamApTask0: Sep 10 13:50:37.367: 00:72:78:19:76:a0 WTP Event Response sent to 172.30.2.93:5272

*spamApTask0: Sep 10 13:50:37.371: 00:72:78:19:76:a0 WTP Event Request from 172.30.2.93:5272 epoch 1536580237

*spamApTask0: Sep 10 13:50:37.371: 00:72:78:19:76:a0 WTP Event Response sent to 172.30.2.93:5272

*spamApTask0: Sep 10 13:50:37.669: 00:38:df:1b:dc:20 Setting ADD_MOBILE ack state for STA a0:99:9b:20:25:b8 (idx 23), seqno 224 action 1
*spamApTask0: Sep 10 13:50:37.678: 00:38:df:1b:dc:20 Configuration Update Response from 172.30.2.51:5256

*spamApTask0: Sep 10 13:50:37.700: 00:38:df:1b:dc:20 Configuration Update Response from 172.30.2.51:5256

*spamApTask0: Sep 10 13:50:38.123: e0:0e:da:f8:7b:ec Join Request from 172.30.3.246:51135

*spamApTask0: Sep 10 13:50:38.123: e0:0e:da:f8:7b:ec Join request received from AP which is already present. Deleting previous connection
172.30. 3.246:51135

*spamApTask0: Sep 10 13:50:38.123: e0:0e:da:f8:7b:ec Multiple Join Request: Join request received from AP which is already present. Deleting pre vious conne
*spamApTask0: Sep 10 13:50:38.123: e0:0e:da:f8:7b:ec Finding DTLS connection to delete for AP (172:30:3:246/51135)
*spamApTask0: Sep 10 13:50:38.123: e0:0e:da:f8:7b:ec Disconnecting DTLS Capwap-Ctrl session 0x6a83d78 for AP (172:30:3:246/51135). Notify(false)
*spamApTask0: Sep 10 13:50:38.123: e0:0e:da:f8:7b:ec CAPWAP State: Dtls tear down

*spamApTask0: Sep 10 13:50:38.123: e0:0e:da:f8:7b:ec Not sending DTLS session closed notification to capwap.(172.30.3.246:51135)
*spamApTask0: Sep 10 13:50:38.124: e0:0e:da:f8:7b:ec AP Delete request
*spamApTask0: Sep 10 13:50:38.124: e0:0e:da:f8:7b:ec DTLS connection not found. Ignoring join request from 172.30.3.246:51135

*spamApTask0: Sep 10 13:50:38.124: e0:0e:da:f8:7b:ec Join Request failed!

*spamApTask0: Sep 10 13:50:38.124: e0:0e:da:f8:7b:ec State machine handler: Failed to process msg type = 3 state = 0 from 172.30.3.246:51135

*spamApTask0: Sep 10 13:50:38.124: e0:0e:da:f8:7b:ec Failed to parse CAPWAP packet from 172.30.3.246:51135

*spamApTask0: Sep 10 13:50:38.125: 00:00:00:00:00:00 Discarding non-ClientHello Handshake OR DTLS encrypted packet from 172.30.3.246:51135)sinc e DTLS session is not established

*spamApTask0: Sep 10 13:50:38.125: 00:00:00:00:00:00 DTLS connection not found, creating new connection for 172.30.3.246 (51135) 172.30.3.238 (5 246)

*spamApTask0: Sep 10 13:50:38.379: 00:00:00:00:00:00 DTLS Session established server (172.30.3.238:5246), client (172.30.3.246:51135)
*spamApTask0: Sep 10 13:50:38.379: 00:00:00:00:00:00 Starting wait join timer for AP: 172.30.3.246:51135

*spamApTask0: Sep 10 13:50:38.382: e0:0e:da:f8:7b:ec Join Request from 172.30.3.246:51135

*spamApTask0: Sep 10 13:50:38.382: e0:0e:da:f8:7b:ec Unable to get Ap mode in Join request

*spamApTask0: Sep 10 13:50:38.382: e0:0e:da:f8:7b:ec Allocate database entry for AP 172.30.3.246:51135, already allocated index 65535

*spamApTask0: Sep 10 13:50:38.382: e0:0e:da:f8:7b:ec AP Allocate request at index ffff
*spamApTask0: Sep 10 13:50:38.383: 00:00:00:00:00:00 Deleting AP entry 172.30.3.246:51135 from temporary database.
*spamApTask0: Sep 10 13:50:38.383: e0:0e:da:f8:7b:ec AP with same name APe00e.daf8.7bec exist. Using default name APe00e.daf8.7bec for this AP. radId 2 dupRadId 2dupApMac: E0:0E:DA:F8:7B:EC

*spamApTask0: Sep 10 13:50:38.383: e0:0e:da:f8:7b:ec Dropping request or response packet to AP :172.30.3.246 (51135) by Controller: 172.30.3.23 8 (5246), message Capwap_wtp_event_response, state Capwap_no_state

*spamApTask0: Sep 10 13:50:38.384: e0:0e:da:f8:7b:ec Message type Capwap_wtp_event_response is not allowed to send in state Capwap_no_state for AP 172.30.3.246

*spamApTask0: Sep 10 13:50:38.384: e0:0e:da:f8:7b:ec Join Request failed!

*spamApTask0: Sep 10 13:50:38.384: e0:0e:da:f8:7b:ec State machine handler: Failed to process msg type = 3 state = 0 from 172.30.3.246:51135

Sepp1 · ‎10-10-2018

Please, does anyone has other ideas?

Leo Laohoo · ‎10-10-2018

@Sepp1 wrote:

The 1852i has fw 8.6.101.0

There's the answer. The final "version" 2600 gets supported is 8.5.X.X.

This is the reason why the ME is "seeing" the 2600 attempt to join and was about to push the firmware down but the process was stopped.

Sepp1 · ‎10-11-2018

Thanks, but please read the whole stuff.
Firmware was downgraded two times. Still does not work.