Hello,We have 2 separate customers using the same setup on their wireless APs (MR devices). Basically, one or more SSIDs are configured in bridge mode with VLAN tagging enabled using VLAN IDs from the local connected Firewall (MX device). The issue w...
Forum Posts
Hello everyone, I have a Cisco IR829 that I'm trying to connect the shown network devices, but I've run into an issue. The Laptop, Switch (3560), and AP (1562e), all connect just fine and can receive DHCP from the Switch; however, when I try to conne...
Resolved! Cisco AIRONET wireless chipsets
Hello,does anyone know, what kind of 3rd party wireless chipsets is Cisco using for Aironets?Thanks
Hi, I have 3 Access points that are behaving very strange. They got a DHCP address in the wrong VLAN, and after changing the switchport access vlan they get no adress. If i change the switchport back to the original VLAN they once again get a DHCP ad...
Cisco WLC 8540Controller software : 8.5.135.0Assignment of Power & Channle : Auto What determines the power level, Is it only the APs bound to your controller or is it all the APs in the vaccinity? Dose channle assignment take account for other APs i...
I am going to upgrade production AP to MR 26.6.1 stable release. Are there any known bugs that I should know about?
I currently have about 50 old AP600s connecting over Internet to three differnet WLC5508 Office Extend Controllers for managers. I wanted to upgrade to a newer AP that supports 802.1ac and have a little more power. I just got a few Air-AP1815W and AP...
Hi,I don't want to use the Service Port\OOB Interface Gig 0 for Management. The preference is to use 2 x 10GB Uplinks in a Port-channel between the WLC and Neighbouring switch for my Management and WLAN Vlans.This config matches exiting 5508 WLCs. O...
Hi, I have problem connecting out of the box Air-AP1852i-E-K9 to my working WLC2500. WLC 2500 running firmware: 7.6.130.0 AP1852 running firmware version: AP Running Image : 8.3.143.0 initially I checked that the time was wrong on the AP and ...
Resolved! Wireless Data Rates
Hello As CAPWAP AP, the AP1701 gives maximum of 400 Mbps data rates to the clients. But when we set the AP1701 as Autonomous, it gives maximum of 144 Mbps only. How can I get 400 Mbps in Autonomous mode ? ThanksCleetus
Resolved! WPA2 PSK with MAC Address Filter
I have read through the Meraki's AP configuration guide about MAC address filtering, and see that it only support via "Association requirements" with "no encryption."In non-Meraki, Cisco-based Wi-Fi infrastructure, you can use both WPA2 encrypted dat...
Resolved! How to create a 2GHZ only SSID
Is it possible to create an SSID that only broadcasts the 2GHz channel on the MR33 Access Point? I have some devices: Apple Watches, Thermostats that only work on the 2GHZ channel. I haven't been able to find anything stating it can or can't be done.
I have a weird issue here.When I tried to use vWLC(running in esxi) to manage my APs(2800 & 1800 series), any devices connected to these APs cannot ping the gateway (actually like 90% icmp packet no reply), these devices will show 'No Internet'. But ...
Hello Cisco community,I need ur help. I have EPC3925 router/modem problem. I searched for hours but i just cant find bandwidth control on 192.168.0.1 site. I need to set net speed (per ip) of some users on my wifi network. I've done that easly on the...
Resolved! Chromecast with Fabric Wifi not working
Hello,I have a fabric network both on wired and wireless configured by DNA Center but because of internal DNAC problems I modify WLC manually. Both Wifi and Wired are in the same network. When my Laptop and Chromecast both are connected with cable an...
