cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
2113
Views
1
Helpful
5
Replies

2702i - AP

Anukalp S
Level 7
Level 7

Hi.. I have a AP 2702i which I have converted it into Autonomous mode. I want to use it as standalone wifi device. I have made changes for this but the SSID which I have set is not broadcasting. SSID is not getting appeared. Am I missing anything. I am using open authentication with PSK, WPA2.

Please suggest what is missing.

5 Replies 5

zdesignstudio
Level 8
Level 8

Please provide the config from the AP.

Please rate useful posts and mark answers as correct if applicable.

Please rate useful posts and mark answers as correct if applicable.

Please see below config.

ap#sh run
Building configuration...

Current configuration : 1950 bytes
!
version 15.3
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
!
hostname ap
!
!
logging rate-limit console 9
enable secret 5 $1$llsg$D.pLZVzE3b.oMBpqKpKqi/
!
no aaa new-model
no ip source-route
no ip cef
!
!
!
!
dot11 pause-time 100
dot11 syslog
!
dot11 ssid LAVAIND
   band-select
   authentication open
   authentication key-management wpa version 2
   wpa-psk ascii 7 1042080F0446405858
   information-element ssidl
!
!
!
no ipv6 cef
!
!
username Cisco password 7 0802455D0A16
!
!
bridge irb
!
!
!
interface Dot11Radio0
 no ip address
 shutdown
 !
 encryption mode ciphers aes-ccm tkip
 !
 ssid LAVAIND
 !
 antenna gain 0
 station-role root
 bridge-group 1
 bridge-group 1 subscriber-loop-control
 bridge-group 1 spanning-disabled
 bridge-group 1 block-unknown-source
 no bridge-group 1 source-learning
 no bridge-group 1 unicast-flooding
!
interface Dot11Radio1
 no ip address
 shutdown
 !
 encryption mode ciphers aes-ccm tkip
 antenna gain 0
 peakdetect
 no dfs band block
 channel dfs
 station-role root
 bridge-group 1
 bridge-group 1 subscriber-loop-control
 bridge-group 1 spanning-disabled
 bridge-group 1 block-unknown-source
 no bridge-group 1 source-learning
 no bridge-group 1 unicast-flooding
!
interface GigabitEthernet0
 no ip address
 duplex auto
 speed auto
 bridge-group 1
 bridge-group 1 spanning-disabled
 no bridge-group 1 source-learning
!
interface GigabitEthernet1
 no ip address
 duplex auto
 speed auto
 bridge-group 1
 bridge-group 1 spanning-disabled
 no bridge-group 1 source-learning
!
interface BVI1
 mac-address 5c83.8fd9.3c2c
 ip address dhcp
 ipv6 address dhcp
 ipv6 address autoconfig
 ipv6 enable
!
ip forward-protocol nd
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
!
!
bridge 1 route ip
!
!
!
line con 0
line vty 0 4
 login local
 transport input all
!
end

===========================================================

ap#sh ip int
BVI1 is up, line protocol is up
  Internet address is 172.16.41.20/24
  Broadcast address is 255.255.255.255
  Address determined by DHCP
  MTU is 1500 bytes
  Helper address is not set
  Directed broadcast forwarding is disabled
  Multicast reserved groups joined:
  Outgoing access list is not set
  Inbound  access list is not set
  Proxy ARP is enabled
  Local Proxy ARP is disabled
  Security level is default
  Split horizon is enabled
  ICMP redirects are always sent
  ICMP unreachables are always sent
  ICMP mask replies are never sent
  IP fast switching is disabled
  IP fast switching on the same interface is disabled
  IP CEF switching is disabled
  IP Null turbo vector
  IP Null turbo vector
  IP multicast fast switching is disabled
  IP multicast distributed fast switching is disabled
  IP route-cache flags are Fast
  Router Discovery is disabled
  IP output packet accounting is disabled
  IP access violation accounting is disabled
  TCP/IP header compression is disabled
  RTP/IP header compression is disabled
  Policy routing is disabled
  Network address translation is disabled
  BGP Policy Mapping is disabled
  Input features: MCI Check
Dot11Radio0 is administratively down, line protocol is down
  Internet protocol processing disabled
Dot11Radio1 is administratively down, line protocol is down
  Internet protocol processing disabled
GigabitEthernet0 is up, line protocol is up
  Internet protocol processing disabled
GigabitEthernet1 is up, line protocol is down
  Internet protocol processing disabled

Sandeep Choudhary
VIP Alumni
VIP Alumni

Hi,

Please use this post to configure your AP properly:

https://rscciew.wordpress.com/2014/05/24/single-ssid-configuration-on-autonomous-ap/

https://mrncciew.com/2012/10/24/multiple-ssid-config-on-autonomous-ap/

Regards

Dont forget to rate helpful posts

Hi,

I have done the same

just I named my AP myap
I put my domain so on the IP 192.168.1.111 = myap.mydomain.xyz

I have a SSL certificate for *.mydomain.xyz

I wish to access to https://myap.mydomain.xyz secure mode.... how or where I can upload the SSL certificate ?

 

I try https://www.cisco.com/c/en/us/td/docs/wireless/access_point/15-3-3-JB/configuration/guide/cg_book/cg-chap2-gui.html the part for (I think to generate a certificate) it didn't work


Many thanks in advance

Regards

Review Cisco Networking for a $25 gift card