09-26-2013 06:24 AM - edited 07-04-2021 12:57 AM
Hi All
Busy with a rollout of a number of new 3602 APs, running into issues with some of them not coming up correctly.
DHCP for each subnet is configured on the local switch where the AP conects, the WLC is at another location.
Port configuration:
interface FastEthernet2/0/45
switchport trunk encapsulation dot1q
switchport trunk native vlan 20
switchport trunk allowed vlan 20,103
switchport mode trunk
mls qos trust cos
end
AP is connected:
Capability Codes: R - Router, T - Trans Bridge, B - Source Route Bridge
S - Switch, H - Host, I - IGMP, r - Repeater, P - Phone
Device ID Local Intrfce Holdtme Capability Platform Po
rt ID
AP4c4e.3560.389d Fas 2/0/45 165 R T AIR-CAP360Gig
0.1
AP has IP address:
IP address Client-ID/ Lease expiration Type
Hardware address
10.104.34.4 014c.4e35.6038.9d Sep 27 2013 11:57 AM Automatic
ping 10.104.34.4 - from local switch
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.104.34.4, timeout is 2 seconds:
.....
Success rate is 0 percent (0/5)
No response....
sh cdp nei f2/0/45 det
-------------------------
Device ID: AP4c4e.3560.389d
Entry address(es):
IP address: 10.104.34.4
Platform: cisco AIR-CAP3602I-E-K9 , Capabilities: Router Trans-Bridge
Interface: FastEthernet2/0/45, Port ID (outgoing port): GigabitEthernet0.1
Holdtime : 127 sec
Version :
Cisco IOS Software, C3600 Software (AP3G2-RCVK9W8-M), Version 12.4(25e)JAL1, REL
EASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Mon 10-Dec-12 23:40 by prod_rel_team
advertisement version: 2
Duplex: full
Power drawn: 13.000 Watts
Power request id: 42177, Power management id: 1
Power request levels are:13000 0 0 0 0
Management address(es):
Correct MAC in table:
Mac Address Table
-------------------------------------------
Vlan Mac Address Type Ports
---- ----------- -------- -----
20 4c4e.3560.389d DYNAMIC Fa2/0/45
Total Mac Addresses for this criterion: 1
DHCP configuration:
ip dhcp excluded-address 10.104.34.1 10.104.34.2
!
ip dhcp pool Wireless-AP
network 10.104.34.0 255.255.255.248
default-router 10.104.34.1
option 43 hex f104.0a49.000b
!
SVI configuration:
interface Vlan20
description Wireless-management
ip address 10.104.34.1 255.255.255.248
no ip redirects
no ip unreachables
From AP log:
%CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
Looks like the does not know that is has an IP address and doesn't even try.
We have this exact DHCP configuraion running at a number of locations so quite sure it works,
Tried static configuration anyway:
AP4403.a734.8e9b#sh capwap ip config
LWAPP Static IP Configuration
IP Address 10.104.34.4
IP netmask 255.255.255.248
Default Gateway 10.104.34.1
Primary Controller 10.73.0.11
Same result:
%CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
Have a few of these new 3602 doing this, out of the box.
Any ideas?
09-26-2013 02:26 PM
Why did you configure switch port as trunk ? Are these deploy as FlexConnect or Local mode ? If possible test it just connecting to a vlan 20 access port & see.
Try "clear capwap private-config" of AP console & try it again. Take the AP console output & post it here if still not working
HTH
Rasika
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide