cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
2457
Views
0
Helpful
2
Replies

a controler 3504 with ios 8.5.131

Dhikra Marghli
Level 5
Level 5

I ask if  a controler 3504 with ios 8.5.131  work with acces point 1815i with version 

beacuse i see in controler 

 

 

etah_CCO/label/mallorca]5), [wireless-lnx2:/san/BUILD/workspace/83MR4_Repost_Che--More--
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2015 by Cisco Systems, Inc.
Compiled Mon Jun 4 22:56:21 PDT 2018

ROM: Bootstrap program is U-Boot boot loader

 

 

////////////////////////////////

(Cisco Controller) >show ap join stats summary all

Number of APs.............................................. 1

Base Mac AP EthernetMac AP Name IP Address Status
a0:93:51:3f:b0:a0 N A AP11 10.1.1.11 Not Joined

 


BOOTLDR: U-Boot boot loader Version 37

AP11 uptime is 0 days, 0 hours, 11 minutes
Last reload time : Wed Feb 13 14:05:32 UTC 2019
Last reload reason : unknown

cisco AIR-AP1815I-I-K9 ARMv7 Processor rev 5 (v7l) with 1015920/847052K bytes of memory.
Processor board ID FGL2221B241
AP Running Image : 8.3.143.0
Primary Boot Image : 8.3.143.0
Backup Boot Image : 8.3.111.0
1 Gigabit Ethernet interfaces
2 802.11 Radios
Radio FW version : 9cef56836c2be4ced5dacbd94f6c28c0
NSS FW version : not available

--More-- [*02/14/2019 07:45:09.0000]

 

//////////////////////////////////////////////

(Cisco Controller) >show tech-support


---------------Show boot---------------

Primary Boot Image............................... 8.5.131.0 (active)
Backup Boot Image................................ 8.5.131.0

---------------show time---------------


Time............................................. Thu Feb 14 07:43:00 2019

Timezone delta................................... 0:0
Timezone location................................

---------------Show Inventory---------------

System Inventory
Burned-in MAC Address............................ DC:F7:19:D3:C0:80
Maximum number of APs supported.................. 150

---------------Show udi---------------

NAME: "Chassis" , DESCR: "Cisco 3500 Series Wireless LAN Controller"
PID: AIR-CT3504-K9, VID: V02, SN: FCW2231M08U

---------------Show sysinfo---------------

System Information
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 8.5.131.0
RTOS Version..................................... 8.5.131.0
Bootloader Version............................... 8.5.103.0
Emergency Image Version.......................... 8.5.103.0

OUI File Last Update Time........................ N/A
Build Type....................................... DATA + WPS

System Name...................................... Cisco_d3:c0:82
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.2427
Redundancy Mode.................................. Disabled
IP Address....................................... 10.1.1.10
IPv6 Address..................................... ::
Last Reset....................................... Cold reset due to PLL_DC_OK

--More-- or (q)uit

 

 

1 Accepted Solution

Accepted Solutions

The AP is supported in the release. The AP is -I for Algeria, do you have the WLC set for the same regulatory domain?

View solution in original post

2 Replies 2

The AP is supported in the release. The AP is -I for Algeria, do you have the WLC set for the same regulatory domain?

Leo Laohoo
Hall of Fame
Hall of Fame
1. Configure NTP on the controller.
2. What country is set for the controller?
3. Make sure the AP is running CAPWAP image (and not ME image).
Review Cisco Networking for a $25 gift card