05-20-2014 11:28 AM - edited 07-05-2021 12:52 AM
I am trying to add AP 1042N with ios15.2(4)JB5 in WLC 2504 with IOS version 7.4.121.0 , but AP is not joining and
Below mentioned is the log I am getting in the AP , here 192.168.100.10 is WLC ip
*May 20 19:31:22.745: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*May 20 19:51:24.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.100.10 peer_port: 5246
*May 20 19:51:24.804: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 192.168.100.10 peer_port: 5246
*May 20 19:51:24.805: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.100.10
*May 20 19:51:29.804: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.100.10
*May 20 19:52:23.222: %DTLS-5-ALERT: Received WARNING : Close notify alert from 192.168.100.10
*May 20 19:52:23.222: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 192.168.100.10:5246
*May 20 19:52:23.223: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*May 20 19:51:24.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.100.10 peer_port: 5246
*May 20 19:51:24.818: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 192.168.100.10 peer_port: 5246
*May 20 19:51:24.819: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.100.10
*May 20 19:51:29.819: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.100.10
Can anyone tell me, is there any issue between the AP & WLC IOS compatibility or what else could be reason for this.
Solved! Go to Solution.
05-20-2014 05:02 PM
Can't be firmware compatibility. Can you post the following command output:
1. WLC: sh sysinfo;
2. AP: sh version; and
3. AP: sh ip interface brief
Your logs is showing the AP is getting the correct time and date. The only culprit left is the AP has a different regulatory domain against the country settings on the WLC.
05-20-2014 05:02 PM
Can't be firmware compatibility. Can you post the following command output:
1. WLC: sh sysinfo;
2. AP: sh version; and
3. AP: sh ip interface brief
Your logs is showing the AP is getting the correct time and date. The only culprit left is the AP has a different regulatory domain against the country settings on the WLC.
05-22-2014 10:44 PM
Hi Thanks for everyone's comments,
I found solution, I i was extracting only one file from the tar image and supporting files were not extracted to flash
Now I did " “archive tar /xtract tftp://<TFTP server IP>/<ImageName>.tar flash: “ and extracted complete tar in to the flash and changed boot priority. Now it is joining to controller
Thank you
05-20-2014 11:25 PM
Hi,
Please provide the info asked by LEO then only we can find out the root cause of issue.
sh version from AP
sh sysinfo from WLC.
Regards
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide