06-12-2016 11:20 PM - edited 07-05-2021 05:12 AM
*Jun 13 06:17:05.715: AP has SHA2 MIC certificate - Using SHA2 MIC certificate for DTLS.
*Jun 13 06:17:06.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.0.100 peer_port: 5246
*Jun 13 06:17:06.331: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 192.168.0.100 peer_port: 5246
*Jun 13 06:17:06.335: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.0.100
*Jun 13 06:17:24.875: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 192.168.0.100:5246
*Jun 13 06:17:24.955: [m102x_set_lanport_config] Cannot enable AUX port while POE, connect AC or Inj source
*Jun 13 06:17:24.967: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Jun 13 06:17:24.967: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to administratively down
*Jun 13 06:17:24.971: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Jun 13 06:17:24.995: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Jun 13 06:17:25.971: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Jun 13 06:17:25.999: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to down
*Jun 13 06:17:26.007: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Jun 13 06:17:26.991: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Jun 13 06:17:26.999: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Jun 13 06:17:27.027: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Jun 13 06:17:27.035: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to down
*Jun 13 06:17:27.043: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Jun 13 06:17:28.027: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
*Jun 13 06:17:28.035: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Jun 13 06:17:28.071: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Jun 13 06:17:29.071: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Jun 13 06:17:37.995: AP has SHA2 MIC certificate - Using SHA2 MIC certificate for DTLS.
06-12-2016 11:35 PM
Post the complete output to the following commands:
1. WLC: sh sysinfo;
2. WLC: sh time;
3. AP: sh version; &
4. AP: sh ip interface brief
06-13-2016 12:00 AM
(Cisco Controller) >show sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 8.1.102.0
Bootloader Version............................... 1.0.20
Field Recovery Image Version..................... 7.6.101.1
Firmware Version................................. PIC 20.0
Build Type....................................... DATA + WPS
System Name...................................... TANGALOY
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1279
IP Address....................................... 192.168.0.100
IPv6 Address..................................... ::
Last Reset....................................... Power on reset
System Up Time................................... 0 days 0 hrs 46 mins 42 secs
System Timezone Location......................... (GMT +7:00) Saigon, Hanoi, Bangkok, Jakatar
System Stats Realtime Interval................... 5
System Stats Normal Interval..................... 180
--More or (q)uit current module or <ctrl-z> to abort
Configured Country............................... Multiple Countries:TH,US
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +37 C
External Temperature............................. +41 C
Fan Status....................................... 3500 rpm
State of 802.11b Network......................... Disabled
State of 802.11a Network......................... Disabled
Number of WLANs.................................. 1
Number of Active Clients......................... 0
Burned-in MAC Address............................ 00:9E:1E:06:74:A0
Maximum number of APs supported.................. 75
System Nas-Id.................................... TANGALOY
WLC MIC Certificate Types........................ SHA1/SHA2
(Cisco Controller) >show time
Time............................................. Mon Jun 13 13:43:26 2016
Timezone delta................................... 0:0
Timezone location................................ (GMT +7:00) Saigon, Hanoi, Bangkok, Jakatar
NTP Servers
NTP Polling Interval......................... 86400
Index NTP Key Index NTP Server NTP Msg Auth Status
------- ----------------------------------------------------------------------------------
AP0062.ecf1.2508#sh ver
Cisco IOS Software, C2700 Software (AP3G2-K9W8-M), Version 15.3(3)JBB, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2015 by Cisco Systems, Inc.
Compiled Mon 04-May-15 17:26 by prod_rel_team
ROM: Bootstrap program is C2700 boot loader
BOOTLDR: C2700 Boot Loader (AP3G2-BOOT-M) LoaderVersion 15.2(4)JB5m, RELEASE SOFTWARE (fc2)
AP0062.ecf1.2508 uptime is 42 minutes
System returned to ROM by power-on
System image file is "flash:/ap3g2-k9w8-mx.153-3.JBB/ap3g2-k9w8-xx.153-3.JBB"
Last reload reason:
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
cisco AIR-AP2702I-UXK9 (PowerPC) processor (revision A0) with 376810K/134656K bytes of memory.
Processor board ID FCW2020NCG8
PowerPC CPU at 800Mhz, revision number 0x2151
Last reset from power-on
LWAPP image version 8.1.102.0
Access Point Type: World Mode
1 Gigabit Ethernet interface
2 802.11 Radios
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 00:62:EC:F1:25:08
Part Number : 73-15824-03
PCA Assembly Number : 000-00000-00
PCA Revision Number :
PCB Serial Number : FOC20196MPF
Top Assembly Part Number : 068-100395-01
Top Assembly Serial Number : FCW2020NCG8
Top Revision Number : A0
Product/Model Number : AIR-AP2702I-UXK9
Configuration register is 0xF
AP0062.ecf1.2508#sh ip int br
Interface IP-Address OK? Method Status Protocol
BVI1 192.168.0.154 YES DHCP up up
Dot11Radio0 unassigned NO unset up up
Dot11Radio1 unassigned NO unset up up
GigabitEthernet0 unassigned NO unset up up
GigabitEthernet1 unassigned NO unset administratively down down
Virtual-WLAN0 unassigned NO unset up up
Virtual-WLAN0.1 unassigned NO unset up up
Virtual-WLAN0.2 unassigned NO unset up up
Virtual-WLAN0.3 unassigned NO unset up up
Virtual-WLAN0.4 unassigned NO unset up up
Virtual-WLAN0.5 unassigned NO unset up up
Virtual-WLAN0.6 unassigned NO unset up up
Virtual-WLAN0.7 unassigned NO unset up up
Virtual-WLAN0.8 unassigned NO unset up up
Virtual-WLAN0.9 unassigned NO unset up up
Virtual-WLAN0.10 unassigned NO unset up up
Virtual-WLAN0.11 unassigned NO unset up up
Virtual-WLAN0.12 unassigned NO unset up up
Virtual-WLAN0.13 unassigned NO unset up up
Virtual-WLAN0.14 unassigned NO unset up up
Virtual-WLAN0.15 unassigned NO unset up up
Virtual-WLAN0.16 unassigned NO unset up up
06-13-2016 12:24 AM
Product/Model Number : AIR-AP2702I-UXK9
AP is not primed. Read this: Cisco Aironet Universal AP Priming and Cisco AirProvision User Guide
Controller may have the wrong time.
06-14-2016 08:54 PM
As your AP is UX, you need to prime the access point for a particular domain.
http://www.cisco.com/c/en/us/td/docs/wireless/access_point/ux-ap/guide/uxap-mobapp-g.html
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide