12-20-2022 08:45 AM
Hi everyone,
I want to configure a Cisco Access Point AIR-AP4800_E-K9. I added it to the controller with an IP address. (Also a AP4800_E-K9).
The access point is not accessible via the web interface. The access point is accessible via ping on the LAN. Does it have to be a specific browser? Do I need to configure http on the access point? What other data do I have to enter on the access point?
Does the controller copy all data such as SSID, WLAN ID to the access point?
Thank you.
12-20-2022 09:01 AM
- If it's a capwap based (client) access point intending to join a controller then it does not have a web-based interface , it becomes managed by the controller. Verify the list of access points on the controller to check if it joined correctly ,
M.
12-21-2022 06:15 AM
Hello,
I see the new access point under the cisco 4800 Mobility express-Controller but there is no uptime und the blue light is blinking on the access point.
12-21-2022 09:40 AM
- As stated , you need to attach a console and post the booting output ,
M.
12-20-2022 09:19 AM
Looking at the model you posted, AIR-AP4800_E-K9, this is a standalone ap unless you have converted the image to CAPWAP. Console into the AP, reboot it and post the output. Attach the output as a text file attachment. The output will tell you what is happening, if the AP is autonomous, or failing to join a controller and why.
12-21-2022 02:36 AM
Hi,
which output do you mean? Which command is best for this?
12-21-2022 06:50 AM
Hello,
I see the new Access Point under the Controller Cisco 4800 Mobility Express:
AP#[*12/21/2022 14:44:14.7933] Invalid event 50 & state 10 combination.
[*12/21/2022 14:44:14.7933] SM handler: Failed to process timer message. Event 50, state 10
[*12/21/2022 14:44:14.7933] Failed to handle timer message.
[*12/21/2022 14:44:14.7933] FSM failure while processing message with id: 1
[*12/21/2022 14:44:14.9833] Image download did not start for 120 seconds.
[*12/21/2022 14:44:14.9833] Restarting capwap - image download cannot start.
[*12/21/2022 14:44:14.9833]
[*12/21/2022 14:44:14.9833] Lost connection to the controller, going to restart CAPWAP...
[*12/21/2022 14:44:14.9833]
[*12/21/2022 14:44:14.9834] Restarting CAPWAP State Machine.
[*12/21/2022 14:44:15.0882] Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Image Data(10).
[*12/21/2022 14:44:15.0902]
[*12/21/2022 14:44:15.0903] CAPWAP State: DTLS Teardown
[*12/21/2022 14:44:16.1051] Dropping dtls packet since session is not established. Peer xxx.xxx.xxx.xxx-5246, Local xxx.xxx.xxx.xxx-5272, conn (nil)
[*12/21/2022 14:44:16.9110] Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: DTLS Teardown(4).
[*12/21/2022 14:44:20.7361] do ABORT, part1 is active part
[*12/21/2022 14:44:30.8579]
[*12/21/2022 14:44:30.8579] CAPWAP State: Discovery
[*12/21/2022 14:44:30.8609] Discovery Request sent to xxx.xxx.xxx.xxx, discovery type STATIC_CONFIG(1)
[*12/21/2022 14:44:30.8637] Discovery Request sent to xxx.xxx.xxx.xxx, discovery type STATIC_CONFIG(1)
[*12/21/2022 14:44:30.8696] Discovery Request sent to xxx.xxx.xxx.xxx, discovery type UNKNOWN(0)
[*12/21/2022 14:44:30.8697] Discovery Response from xxx.xxx.xxx.xxx
[*12/21/2022 14:44:40.0000] TLV-DEC-ERR-1: No proc for 661
[*12/21/2022 14:44:40.0002] Discovery Response from 1xxx.xxx.xxx.xxx
[*12/21/2022 14:44:40.0000] TLV-DEC-ERR-1: No proc for 661
[*12/21/2022 14:44:40.0000] Discovery Response from xxx.xxx.xxx.xxx
[*12/21/2022 14:44:40.0000] TLV-DEC-ERR-1: No proc for 661
[*12/21/2022 14:44:40.0000]
[*12/21/2022 14:44:40.0000] CAPWAP State: DTLS Setup
[*12/21/2022 14:44:40.6769]
[*12/21/2022 14:44:40.6769] CAPWAP State: Join
[*12/21/2022 14:44:40.6788] Sending Join request to xxx.xxx.xxx.xxx through port 5272
[*12/21/2022 14:44:40.6822] Join Response from xxx.xxx.xxx.xxx
[*12/21/2022 14:44:40.6822] TLV ID 788 not found
[*12/21/2022 14:44:40.6823] TLV-DEC-ERR-1: No proc for 788
[*12/21/2022 14:44:40.6823] TLV-DEC-FAILED for TLV_FLEXEXPRESS_AP_TYPE_PAYLOAD(786)
[*12/21/2022 14:44:40.7572] HW CAPWAP tunnel is ADDED
[*12/21/2022 14:44:40.7690]
[*12/21/2022 14:44:40.7690] CAPWAP State: Image Data
[*12/21/2022 14:44:40.8069] do PRECHECK, part1 is active part
[*12/21/2022 14:44:40.9456] Image Data Request sent to xxx.xxx.xxx.xxx
12-21-2022 07:03 AM
Hello,
I see on the Cisco 4800 Mobility express, that there is no uptime on the new access point and the blue light is blinking.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide