Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Hello, I have configured 2 150 AX access points to work as a mesh network, but when I scan the networks with my linux laptop I see them listed as "type: Infra" and when testing the automatic switch from one node to another does not work.Any advise ?
Our customer is experiencing user disconnection problems with the 5520 controller, which is managing two access points, the 9120 and 2702. They have only one SSID being broadcasted. Users are encountering random disconnection issues, typically after ...
Hello Guys,We are running wireless setup with foreign and anchor WLC setup and sponsor portal hosting on ISE with L3 on firewall. Guest users are able to connect SSID and when we select profile on Sponsor portal (Profiles confgured on ISE) as Daily, ...
I have two SSIDs AP1 and AP2 both of which leverage MAC authentication device list defined under AAA Advanced, Device Authentication. I have defined the Attribute List Name and WLAN profiles specific to each MAC in an attempt to limit the SSID that ...
Hi all,We use 9800, version 17.3.3 and upgraded to 17.3.6 a month ago, we have AP 1702,2702,1832 and 9105 which is why we did not upgrade to a higher version like 17.9.x. Then we encountered the problem of WIFI disconnection at random, regardless of ...
Hi, I was trying to run just plain simulation of Signal Coverage patterns on Ekahau for CW9166 and MR57 and match the propagation patterns with Datasheets just to see how good they are when being compared to datasheet Coverage patterns. Please note ,...
Hello Everyone,I need to migrate some AP 1852 with Mobility Express to newly 9800 Controller appliance but I'm quite confused on how to do itFrom documentation, I found the conversion could be done with this command:(Cisco Controller) >config ap unif...
I have a new 9800-CL virtual appliance setup at a 3rd party (multi-tenant) datacenter VMware environment.In my personal lab environment, I set up the WMI to be an SVI VLAN interface (which routed through Gig2 on the appliance that I had trunked).In t...
Hello every one here, am badly in need of any help, i recommended my client to buy cisco AP for his different locations, but all APs bought (50) are in lightweight mode, i need to convert them to autonomous because they are to be used in different p...
Hello All,We recently upgraded our C9800 from 17.6.x to 17.9.4a. Following the upgrade, three of our networks would not turn back up without some security modifications, which was straight forward for two of them. However, for our guest wireless ...
Hello,Good day!We are experiencing WhatsApp calls on iPhone dropped when the phone roaming between Cisco APs in the office; remember there is settings on WLC to rectify the short period of WiFi disconnection when Apple device roaming under one AP to ...
https://documentation.meraki.com/MR/MR_Installation_Guides/CW9163E-MR_Installation_GuideThe marketing pages haven't posted yet on cisco.com or meraki.cisco.com (it's dual identity) but it's available to order.A number of caveats with regards to 6Ghz ...
Resolved! lightweight access point 1832 error log
Hello,I have a four 1832i access points with similar error result. - Would you please help me to consider what the problem is ?I know that there is 2 partition in each AP. I wan to cleanup all the firmware from all portions.- Is there any way to comp...
Resolved! Airdrop session
Hello,I am seeing thousands of airdrops sessions on the WLC. I think these are employees with airdrop enabled on the person iPhones. Does anyone know if this can cause interference on the wireless network?
I have 802.1X configured with all my Meraki network switches and works fine. I just changed my Meraki AP's from Pre-Shared key (PSK) configuration to Enterprise with "My RADIUS server" and will not connect.
