Hi all! I have an Cisco AP, model AIR-CAP1602I-E-K9. I have it set up as an autonomous ap and it's all working fine. However, I'm only able to achieve 54 mbit/s. I believe something is wrong with my configuration?
#show running-config
Building configuration...
Current configuration : 3258 bytes
!
! Last configuration change at 14:52:12 CET Mon Mar 1 1993 by cisco
version 15.3
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
service sequence-numbers
!
hostname AP02
!
!
logging rate-limit console 9
enable secret 5 *************
!
no aaa new-model
clock timezone CET 1 0
no ip source-route
no ip cef
!
!
!
!
dot11 syslog
!
dot11 ssid ssid01_24
authentication open
authentication key-management wpa version 2
wpa-psk ascii 7 141B411F01573D7A227962
!
dot11 ssid ssid02_5G
authentication open
authentication key-management wpa version 2
guest-mode
wpa-psk ascii 7 0457581202725B1F0F48
!
!
!
!
!
username CISCO password 7 *********
!
!
bridge irb
!
!
!
interface Dot11Radio0
no ip address
!
encryption mode ciphers aes-ccm tkip
!
ssid ssid01_24
!
antenna gain 0
stbc
beamform ofdm
speed basic-1.0 2.0 5.5 11.0 6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0 m0. m1. m2. m3. m4. m5. m6. m7. m8. m9. m10. m11. m12. m13. m14. m15.
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
!
interface Dot11Radio1
no ip address
!
encryption mode ciphers aes-ccm tkip
!
ssid ssid02_5G
!
antenna gain 0
peakdetect
no dfs band block
stbc
beamform ofdm
speed basic-6.0 basic-9.0 basic-12.0 basic-18.0 basic-24.0 basic-36.0 basic-48.0 basic-54.0 m0. m1. m2. m3. m4. m5. m6. m7. m8. m9. m10. m11. m12. m13. m14. m15.
channel width 40-above
channel 5700
station-role root access-point
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
!
interface GigabitEthernet0
no ip address
duplex auto
speed auto
bridge-group 1
bridge-group 1 spanning-disabled
no bridge-group 1 source-learning
!
interface BVI1
mac-address 6c41.6aba.f5c1
ip address dhcp client-id GigabitEthernet0
ipv6 address dhcp
ipv6 address autoconfig
!
ip forward-protocol nd
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
!
!
snmp-server view dot11view ieee802dot11 included
snmp-server community public RO
snmp-server chassis-id AP02
snmp-server enable traps snmp authentication linkdown linkup coldstart warmstart
snmp-server enable traps tty
snmp-server enable traps entity
snmp-server enable traps disassociate
snmp-server enable traps deauthenticate
snmp-server enable traps authenticate-fail
snmp-server enable traps dot11-qos
snmp-server enable traps switch-over
snmp-server enable traps rogue-ap
snmp-server enable traps wlan-wep
snmp-server enable traps config-copy
snmp-server enable traps config
snmp-server enable traps config-ctid
snmp-server enable traps syslog
snmp-server enable traps cpu threshold
snmp-server enable traps aaa_server
snmp-server enable traps vrfmib vrf-up vrf-down vnet-trunk-up vnet-trunk-down
snmp-server host 10.1.1.10 public
bridge 1 route ip
!
!
!
line con 0
line vty 0 4
login local
transport input all
!
end
Here's my show version.
Cisco IOS Software, C1600 Software (AP1G2-K9W7-M), Version 15.3(3)JAB, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Tue 02-Sep-14 20:36 by prod_rel_team
ROM: Bootstrap program is C1600 boot loader
BOOTLDR: C1600 Boot Loader (AP1G2-BOOT-M) LoaderVersion 15.2(2)JAX, RELEASE SOFTWARE (fc1)
AP02 uptime is 13 hours, 44 minutes
System returned to ROM by power-on
System image file is "flash:/ap1g2-k9w7-mx.153-3.JAB/ap1g2-k9w7-xx.153-3.JAB"
Last reload reason:
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
export@cisco.com.
cisco AIR-SAP1602I-E-K9 (PowerPC) processor (revision B0) with 187382K/74672K bytes of memory.
Processor board ID *****
PowerPC CPU at 533Mhz, revision number 0x2151
Last reset from power-on
1 Gigabit Ethernet interface
2 802.11 Radios
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: *****
Part Number : 73-14671-04
PCA Assembly Number : 000-00000-00
PCA Revision Number :
PCB Serial Number : *****
Top Assembly Part Number : *****
Top Assembly Serial Number : *****
Top Revision Number : A0
Product/Model Number : AIR-CAP1602I-E-K9
Configuration register is 0xF
