04-02-2019 12:02 AM - edited 07-05-2021 10:10 AM
Hi,
I'm having Cisco AIR-AP1562I-D-K9 running SWAP1560-LOCAL-K9 - Cisco 1560 Series Unified Local Mode Software image and Mobility Express Controller Cisco AIR-AP2802I-D-K9C.
Is it AP1562I-D-K9 having CAPWAP Image registered into Cisco AP 2802 running Mobility Express Image, If not then how can i convert AP 1562I-D-K9 current image into Mobility Express Image so that it can registered it into AP 2802I running ME Image.
Thanks in Advance.
Regards,
Vishal
04-02-2019 02:18 AM
04-02-2019 03:16 AM
Hi Patoberli,
Thanks for your reply, but could you please put more light that commands shows in shared link by you can be excuted on AIR-AP1562I-D-K9 running CAPWAP Software in local Mode.
Steps shown in Links
Case 1: If the AP Image type is MOBILITY EXPRESS IMAGE and AP configuration is NOT MOBILITY EXPRESS CAPABLE, enter the command below to change the AP Configurationto MOBILITY EXPRESS CAPABLE .
AP#ap-type mobility-express
Case 2 : If the AP Image type and AP Configuration are not available, it means that the AP is running CAPWAP image. To do the conversion, execute the command below:
AP#ap-type mobility-express tftp://<TFTP Server IP>/<path to tar file>
Example:
AP#ap-type mobility-express tftp://10.18.22.34/AIR-AP1850-K9-8.7.102.0.tar Starting the ME image download... It may take few minutes to finish the download. Image downloaded, writing to flash... do PREDOWNLOAD, part1 is active part sh: CHECK_ME: unknown operand Image start 0x40355008 size 0x01dae41a file size 0x01dae7ca Key start 0x42103422 size 0x00000230 Sinature start 0x42103652 size 0x00000180 Verify returns 0 btldr rel is 16 vs 16, does not need update part to upgrade is part2 activate part2, set BOOT to part2 AP primary version: 8.1.105.37 Archive done. Oe as AP needs to boot up with ME image The system is going down Now! sent SIGTERM to all processes sent SIGKILL to all processes Requesting system reboot79] [07/24/2015 18:19:43.0887] Restarting system. [07/24/2015 18:19:43.1257] Going down for restart now
Note | After the image download is complete, it will be written to the flash followed by a reboot. After the AP comes up, AP Image type will be MOBILITY EXPRESS IMAGEand AP Configuration will MOBILITY EXPRESS CAPABLE |
Please advise.
Regards,
Vishal
04-02-2019 03:51 AM
What is the output when you do a show version command via console? Is this comparable to output given in the link?
04-02-2019 03:18 AM
Hi Patoberli,
Thanks for your reply, but could you please put more light that commands shows in shared link by you can be excuted on AIR-AP1562I-D-K9 running CAPWAP Software in local Mode.
Steps shown in Links
Case 1: If the AP Image type is MOBILITY EXPRESS IMAGE and AP configuration is NOT MOBILITY EXPRESS CAPABLE, enter the command below to change the AP Configurationto MOBILITY EXPRESS CAPABLE .
AP#ap-type mobility-express
Case 2 : If the AP Image type and AP Configuration are not available, it means that the AP is running CAPWAP image. To do the conversion, execute the command below:
AP#ap-type mobility-express tftp://<TFTP Server IP>/<path to tar file>
Example
AP#ap-type mobility-express tftp://10.18.22.34/AIR-AP1850-K9-8.7.102.0.tar
After the image download is complete, it will be written to the flash followed by a reboot. After the AP comes up, AP Image type will be MOBILITY EXPRESS IMAGEand AP Configuration will MOBILITY EXPRESS CAPABLE
Regards,
Vishal
04-02-2019 04:47 AM
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide