how to active ssh state?

[datin]

My accest point seri 9115AXE-F

AP Name : AP6871.619E.C948
Admin State : Enabled
AP Mode : Local
AP Submode : Not Configured
Location : default location
Primary controller name : 
Secondary controller name :
Tertiary controller name :
AP join priority : 1
IP Prefer-mode : Unconfigured
CAPWAP UDP-Lite : Unconfigured
Last Joined Controller name:
DTLS Encryption State : Disabled
Discovery Timer : 10
Heartbeat Timer : 30
CDP State : Enabled
Watchdog monitoring : Enabled
IOX : Disabled
RRM State : Enabled
LSC State : Disabled
SSH State : Disabled
AP Username : Cisco
Session Timeout : 300
Extlog Host : 255.255.255.255
Extlog Flags : 0
Extlog Status Interval : 0
Syslog Host : 255.255.255.255
Syslog Facility : 0
Syslog Level : errors
Core Dump File Compression : Disabled
Core Dump Filename :
Client Trace Status : Enabled(All)
Client Trace All Clients : Enabled
Client Trace Filter : 0x0000000E
Client Trace Out ConsoleLog: Disabled
AP WSA Mode : Disabled
Auxiliary-client Interface : Disabled

[marce1000]

                     - Is it standalone or attached to a controller ?

 M.

[datin]

i right now standalone

[marce1000]

 - Check this guide to configure ssh : https://mrncciew.com/2023/08/28/ios-xe-ssh-best-practices/

 M.

[datin]

how can i in 

AP_TEKNIK(Main)#conf t
                                    ^
% Invalid input detected at '^' marker.

[marce1000]

               AP_TEKNIK(Main)#conf t  ==> % Invalid input detected at '^' marker.
          - If you say the AP is intended for standalone , is it running a correct image ?

 M.

[datin]

cisco C9115AXI-F ARMv8 Processor rev 0 (v8l) with 1971460/1188464K bytes of memory.
Processor board ID FGL2743L7EQ
AP Running Image : 17.9.4.27
Primary Boot Image : 17.9.4.27
Backup Boot Image : 8.10.130.0
Primary Boot Image Hash: 84738f7b5a816bd0a01dac0226c6ac6864711cdd62f5fbb610fff9604011b780260bab0394cd82a72c8e6c367b145d4dd1423c68f52b63a523dd3fb30eae7e9e
Backup Boot Image Hash:
AP Image type : EWC-AP IMAGE
AP Configuration : NOT ME OR EWC-AP CAPABLE
1 Multigigabit Ethernet interfaces
2 802.11 Radios
Radio Driver version : Broadcom BCA: 17.20 RC10.0
Radio FW version : 1570.15680.r47544 47544
NSS FW version : NA

Base ethernet MAC Address : 68:71:61:9E:C7:A4
Part Number : 0-000000-00
PCA Assembly Number : 074-122076-03
PCA Revision Number : C0
PCB Serial Number : FOC27401WR6
Top Assembly Part Number : 074-122076-03
Top Assembly Serial Number : FGL2743L7EQ
Top Revision Number : A0
Product/Model Number : C9115AXI-F

[marce1000]

                    - Check if user is has full admin privilege's  and or try from console , 

 M.

[datin]

i just can open witch console, nothing else

[marce1000]

 - From an earlier reply of yours I saw :
            >...AP Configuration : NOT ME OR EWC-AP CAPABLE

    Follow this document : https://www.cisco.com/c/en/us/support/docs/wireless/embedded-wireless-controller-on-catalyst-access-points/215303-embedded-wireless-controller-conversion.html
                              to get native EWC AP and try again , 

 M.