Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Hi all, i'm looking for an outdoor LTE antenna that would fit on the C921-4PLTEAU, with similar characteristics to this: XPOL-002-5G. It's not so easy to find ISR900 LTE antennas, other than the standard indoor dipole: LTE-ANTM-SMA-D.Any ideas where ...
I have seen this issue in many versions on 9800s now. For some reason, when trying to apply Tags to APs by assigning them to a Location through the Web interface you always receive an error stating that the RF Policies should be different for the 2.4...
I connected a few 1562's to a 5508 WLC. I planned on placing them in Flex+Bridge mode, but this option was not available. I'm assuming that either the 5508 is too old or the 1562's are not capable of Flex+Bridge mode(not likely). Is there a minimum ...
WLC 5520 8.5.171.0according to the documentation,4 AP1810W (and 1815w) has 3 LAN ports, which are configured through "Ports/Module"5 OEAP1810 LAN1/LAN2 are configured through "Ports/Module," with RLAN "None" represents local port. LAN3 is always a lo...
Resolved! No response ip sla responder
Hello guys.When enabling IP SLA on 1800s sensors and connecting to C9130 or C4800 access points, I get the error 'No response ip sla responder'. At the same time I see: that on some points the ip sla responder is enabled, and on some it is disabled, ...
Bill Of Material (BOM)I need a Bill Of Material (BOM) for the Main Part Number = AP9105 InternalSince the former Cisco Aironet 1830 series has come to the end of Sale Would you please help me with the BOM. I will add them to a 5520 WLC. By now th...
Hi!We run 5520 with software 8.3.133 and want to upgrade it to 8.10.x to be able to run the Catalyst 9120 APs.The problem is that we have 100 APs 2600 model in production that we can not change right now because of very long wait time of new APs, and...
HelloThere is a cluster in HA. The primary node is reinstalled and it is not possible to restore HA with the secondary.At the same time, the secondary node is currently active and HA is configured on it. It cannot be removed.How can I remove HA on th...
Hello.This is what happens. Recently we replaced and connected 45 new AIR-AP1852I-E-K9 APs to non-PoE switches. However, we used TP-Link Power adapter to power all APs so WLC showed "PoE/Medium Power". To solve this we bought Cisco PWRINJ6 power inje...
Hi team!I'm just a user with zero knowledge on IP phone setup. We recently purchased a Cisco IP 8865 to use it with out third-party phone system (Vonage). We found out that the device came with enterprise software instead of 3PCC or MPP. The seller j...
I need a Bill Of Material (BOM) for the Main Part Number = AIR-AP1832I-E-K9 KWC22420649Cisco Aironet 1800 Series (IEEE 802.11ac) Access Point Would you pleas help me with that? Thank you Wil Gomez
Hi community! I recently purchased an 8865 IP Phone to use it with my Vonage phone service as a remote worker. I followed all Vonage's activation steps but it never provisions, a "cannot access this page" message is being displayed. I've tried all tr...
what is the different btw these 2?the controller, where/when should configure default domain or group?confused.
Hi MasterI looking solution for disable wireless client communication(client to client) i try to action "drop" P2P Blocking on WLAN butt still not working , Is there anyway to block communication from WLC , All APs on FlexConnection mode thank y...
Hello,Could you please tell me the wattage or milliwattage output of cisco model AIR-AP1262N-A-K9?Thanks,Travis
