12-12-2016 06:56 AM - edited 07-05-2021 06:13 AM
Dears,
I purchased 4G LTE module and I want to use it with Cisco Router 4351. When I Install the module inside the Router and power on the device,
Cisco Router doen not sense the module and no interfaces appears.
is there any difference between ISR G2 and G3 ( EHWIC and NIM ) or just names?
Thanks
12-12-2016 07:11 AM
do you see it in show inventory ?
Do you have th required ios version 3.15.1 or higher ?
Wireless WAN (3G, 4G, LTE) | ||||||||
---|---|---|---|---|---|---|---|---|
NIM-4G-LTE-GA | Yes | Yes | Yes | Yes | Yes | 16.4.1 | 3.15.1 | 4G LTE NIM for Global (Europe, Australia & New Zealand) Data Sheet |
NIM-4G-LTE-NA | Yes | Yes | Yes | Yes | Yes | 16.4.1 | 3.15.1 | 4G LTE NIM for North America AT&T and Canada Data Sheet |
12-12-2016 11:19 AM
I didn't see it in show inventory and Router IOS is greater than 3.15.1 also
12-13-2016 01:22 AM
that sounds as if its DOA it does happen but rarely , did you reseat it yes and still the same , send it back as faulty
12-27-2016 02:05 AM
Hi Mark,
Fortunately, the issue was solved by upgrade the IOS-XR to latest one.
but when i configure the cellular interface, i can't put the encapsulation option to "slip"
and the interface doesn't take an IP.
but the other router was working normally and acquired IP address.
can you help me which config will work with this router?
Current IOS is: isr4300-universalk9.03.16.04b.S.155-3.S4b-ext.SPA.bin
Current Config is:
controller Cellular 0/3/0
lte sim data-profile 1 attach-profile 1
lte modem link-recovery rssi onset-threshold -110
lte modem link-recovery monitor-timer 20
lte modem link-recovery wait-timer 10
lte modem link-recovery debounce-count 6
interface Cellular0/3/0
ip address negotiated
dialer in-band
dialer-group 1
pulse-time 1
encapsulation ppp
dialer-list 1 protocol ip permit
Thanks
10-17-2017 03:43 AM
10-23-2017 03:28 PM
I have the same problem. encapsulation slip and dialer string command not available. Did anyone find the solution?
10-30-2017 05:06 AM
Same problem here,
no chance encapsulation slip being available.
version 4431:
isr4400-universalk9.03.16.04b.S.155-3.S4b-ext.SPA.bin
NAME: "NIM subslot 0/1", DESCR: "NIM-4G-LTE-GA Module"
PID: NIM-4G-LTE-GA , VID: V01, SN: FXXXXXXXXX
NAME: "Modem 0 on Cellular0/1/0", DESCR: "Sierra Wireless MC7304 4G-GA"
PID: MC7304 4G-GA , VID: 1.0, SN: XXXXXXXX
Any hints?
10-30-2017 03:16 PM
You don't need encapsulation slip nor dial string. Just make sure that you have a static route to send traffic to the cell interface. LTE establishes connection based on demand. Once you have route to use the Cell interface, use ping to create some traffic to send to the Cell interface. It should establish a connection. good luck.
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: