cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
35702
Views
0
Helpful
32
Replies

Operational Status DOWN -WLC 2504 and LAP 3501

HEATH FREEL
Level 1
Level 1

The AP is connected to the WLC but keeps taking it's Raodio Down. As suggested I have played with the PoE settings to no avail.....


Wed Feb 1 18:30:36 2012
AP's Interface:0(802.11b) Operation State Down: Base Radio MAC:e8:ba:70:93:81:60 Cause=Radio interface reset. Status:NA
3Wed Feb 1 18:30:36 2012AP's Interface:0(802.11b) Operation State Up: Base Radio MAC:e8:ba:70:93:81:60 Cause=Admin change on Radio Status:Enable
4Wed Feb 1 18:30:36 2012AP's Interface:0(802.11b) Operation State Down: Base Radio MAC:e8:ba:70:93:81:60 Cause=Admin change on Radio Status:Disable
5Wed Feb 1 18:25:32 2012AP's Interface:0(802.11b) Operation State Down: Base Radio MAC:e8:ba:70:93:81:60 Cause=Radio interface reset. Status:NA
6Wed Feb 1 18:25:29 2012AP's Interface:0(802.11b) Operation State Up: Base Radio MAC:e8:ba:70:93:81:60 Cause=Radio reset due to Init. Status:NA

Any Ideas... I have checked everything... AP is in Port 4 of the WLC

32 Replies 32

what happens when you go into the radio and manully change it down then up?

Steve

HTH,
Steve

------------------------------------------------------------------------------------------------
Please remember to rate useful posts, and mark questions as answered

It goes down again.

@Leo, it's enabled

State of 802.11b Network......................... Enabled

State of 802.11a Network......................... Disabled

Number of WLANs.................................. 2

Number of Active Clients......................... 0

the AP is -A and the regulator is CA(which supports -A AP)

@Heath  Can you try another AP?

Steve

HTH,
Steve

------------------------------------------------------------------------------------------------
Please remember to rate useful posts, and mark questions as answered

Ya - I guess I'll have to hunt another one down...

@Leo, it's enabled

Awwww ... too bad.

Hey Heath,

Can you console into the WAP (again) and post the output to the command "dir" please?

Good Morning... Here is the output

APe8b7.48ac.1050#dir

Directory of flash:/

    2  -rwx        6168   Feb 1 2012 21:45:48 +00:00  private-multiple-fs

    5  -rwx      102709   Feb 1 2012 18:23:24 +00:00  event.log

    6  -rwx         275   Feb 1 2012 21:37:13 +00:00  env_vars

    7  drwx         640  Jul 26 2011 07:04:25 +00:00  ap3g1-k9w8-mx.124-23c.JA2

   11  drwx         128   Mar 1 2002 00:09:56 +00:00  ap3g1-rcvk9w8-mx

31481856 bytes total (23166976 bytes free)

APe8b7.48ac.1050#

Can you try this:  Monitor > All AP > Details > Choose the WAP in question > under Admin Status > Enable

Go to the Advanced Tab and under Power over Ethernet settings, make sure nothing is ticked.

Yes I did that as my first step as I have run into that before.... But this time no luck....

I am blown away that two brand new devices designed to work together are so cumbersome to get working.

Well if you are still having issues, you might as well just try to upload the image back onto the wlc. erase the configuration on the wlc and start from scratch.  Might as well put the 7.0.220.0 code on the wlc.

-Scott
*** Please rate helpful posts ***

Upgraded to 7.0.230.0 and nothing has changed.... I beginning to look at the whole WLC option as a piece of CR*P

Did you erase the configuration and start from scratch... not a restore from backup either.  That has helped me in the past a few times.

-Scott
*** Please rate helpful posts ***

Just tried - clear all config in AP and WLC ..... Same issue....

About to go out an buy a Meru

Well since you cleared the wlc config... the last thing I would do is this from the console of the AP:

config t

Entered the username and password (Cisco is the default)

debug capwap console cli

erase /all nvram:

[confirm]

undebug all

reload

[confirm]

-Scott
*** Please rate helpful posts ***

SAME!!!!!

Loading "flash:/ap3g1-k9w8-mx.124-23c.JA4/ap3g1-k9w8-mx.124-23c.JA4"...#########                                ################################################################################                                ################################################################################                                ################################################################################                                ################################################################################                                ################################################################################                                ##################################################

File "flash:/ap3g1-k9w8-mx.124-23c.JA4/ap3g1-k9w8-mx.124-23c.JA4" uncompressed a                                nd installed, entry point: 0x4000

executing...

enet halted

              Restricted Rights Legend

Use, duplication, or disclosure by the Government is

subject to restrictions as set forth in subparagraph

(c) of the Commercial Computer Software - Restricted

Rights clause at FAR sec. 52.227-19 and subparagraph

(c) (1) (ii) of the Rights in Technical Data and Computer

Software clause at DFARS sec. 252.227-7013.

           cisco Systems, Inc.

           170 West Tasman Drive

           San Jose, California 95134-1706

Cisco IOS Software, C3500 Software (AP3G1-K9W8-M), Version 12.4(23c)JA4, RELEASE                                 SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2012 by Cisco Systems, Inc.

Compiled Fri 27-Jan-12 19:44 by prod_rel_team

Proceeding with system init

Proceeding to unmask interrupts

Initializing flashfs...

FLASH CHIP:  Numonyx P33

Checking for Over Erased blocks

................................................................................                                ................................................................................                                ................................................................................                                ......

flashfs[1]: 32 files, 8 directories

flashfs[1]: 0 orphaned files, 0 orphaned directories

flashfs[1]: Total bytes: 31481856

flashfs[1]: Bytes used: 8317952

flashfs[1]: Bytes available: 23163904

flashfs[1]: flashfs fsck took 7 seconds.

flashfs[1]: Initialization complete.

flashfs[2]: 0 files, 1 directories

flashfs[2]: 0 orphaned files, 0 orphaned directories

flashfs[2]: Total bytes: 11999232

flashfs[2]: Bytes used: 1024

flashfs[2]: Bytes available: 11998208

flashfs[2]: flashfs fsck took 1 seconds.

flashfs[2]: Initialization complete....done Initializing flashfs.

Ethernet speed is 1000 Mb - FULL duplex

Radio0  present 8364B 8000 B8020000 0 B8030000 10

This product contains cryptographic features and is subject to United

States and local country laws governing import, export, transfer and

use. Delivery of Cisco cryptographic products does not imply

third-party authority to import, export, distribute or use encryption.

Importers, exporters, distributors and users are responsible for

compliance with U.S. and local country laws. By using this product you

agree to comply with applicable laws and regulations. If you are unable

to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:

http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to

export@cisco.com.

cisco AIR-CAP3501I-A-K9    (PowerPC460exr) processor (revision A0) with 81910K/4                                9152K bytes of memory.

Processor board ID FTX1523E3L1

PowerPC460exr CPU at 666Mhz, revision number 0x18A8

Last reset from reload

LWAPP image version 7.0.230.0

1 Gigabit Ethernet interface

1 802.11 Radio(s)

32K bytes of flash-simulated non-volatile configuration memory.

Base ethernet MAC Address: E8:B7:48:AC:10:50

Part Number                          : 73-12175-05

PCA Assembly Number                  : 800-32268-05

PCA Revision Number                  : A0

PCB Serial Number                    : FOC15163XLD

Top Assembly Part Number             : 800-32902-01

Top Assembly Serial Number           : FTX1523E3L1

Top Revision Number                  : A0

Product/Model Number                 : AIR-CAP3501I-A-K9

% Please define a domain-name first.

Press RETURN to get started!

Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)

*Mar  1 00:00:09.563: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self t                                est passed

*Mar  1 00:00:09.572: *** CRASH_LOG = YES

*Mar  1 00:00:09.572: Port 0 is not present

*Mar  1 00:00:09.572: 64bit PCIE devicesSecurity Core found.

Base Ethernet MAC address: E8:B7:48:AC:10:50

*Mar  1 00:00:12.183: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state                                 to up

*Mar  1 00:00:12.988: %SOAP_FIPS-2-SELF_TEST_RAD_FAILURE: RADIO crypto FIPS self                                 test failed at 128 bit AMAC AEC CCM encrypt on interface Dot11Radio 0 -Process=                                 "Init", ipl= 0, pid= 3

*Mar  1 00:00:13.035: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log                                 (contains, 1024 messages)

*Mar  1 00:00:13.054:  status of voice_diag_test from WLC is false

*Mar  1 00:00:14.083: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEth                                ernet0, changed state to up

*Mar  1 00:00:15.152: %SYS-5-RESTART: System restarted --

Cisco IOS Software, C3500 Software (AP3G1-K9W8-M), Version 12.4(23c)JA4, RELEASE                                 SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2012 by Cisco Systems, Inc.

Compiled Fri 27-Jan-12 19:44 by prod_rel_team

*Mar  1 00:00:15.152: %SNMP-5-COLDSTART: SNMP agent on host ap is undergoing a c                                old start

*Mar  1 00:10:40.044: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to r                                eset

*Mar  1 00:10:41.044: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio                                0, changed state to down

*Mar  1 00:10:52.044: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY

*Mar  1 00:10:52.208: %SSH-5-ENABLED: SSH 2.0 has been enabled

*Mar  1 00:10:58.937:  status of voice_diag_test from WLC is false

*Mar  1 00:10:58.997: Logging LWAPP message to 255.255.255.255.

*Mar  1 00:11:06.468: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power s                                ource

*Feb  3 20:10:47.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_i                                p: 10.161.98.20 peer_port: 5246

*Feb  3 20:10:48.000: %CAPWAP-5-CHANGED: CAPWAP changed state to

wmmAC status is FALSE

*Feb  3 20:10:48.522: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully                                 peer_ip: 10.161.98.20 peer_port: 5246

*Feb  3 20:10:48.522: %CAPWAP-5-SENDJOIN: sending Join Request to 10.161.98.20

*Feb  3 20:10:48.522: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN

*Feb  3 20:10:48.682: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG

*Feb  3 20:10:48.786: %CAPWAP-5-CHANGED: CAPWAP changed state to UP

*Feb  3 20:10:48.830: %CAPWAP-5-JOINEDCONTROLLER: AP has joined controller Cisco                                _e1:da:a4

*Feb  3 20:10:48.877: %LWAPP-3-CLIENTEVENTLOG: SSID test added to the slot[0]

*Feb  3 20:10:48.881: %WIDS-5-ENABLED: IDS Signature is loaded and enabled

*Feb  3 20:10:48.884: %SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.                                255 started - CLI initiated

*Feb  3 20:11:22.999: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power s                                ource

User Access Verification

Username:

Username:

% Username:  timeout expired!

I don't know... I haven't had any issues so far with a 2504.  Might as well open a TAC case so they can actually see your settings.

-Scott
*** Please rate helpful posts ***
Review Cisco Networking for a $25 gift card