step by step - no DHCP or Internet via 2505 Controller
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-27-2023 02:26 AM
Hello,
i have setup a 2504 Controler for a WLAN
on the Advanced Tab i configure a DHCP Server (i cant ping my DHCP/DNS Server)
I even get an ipv6 address from the WLAN AP, but no ipv4 address and no DHCP / DNS from the LAN. Everything works on the LAN.
What do I have to set up on the controller so that the WLAN controller can take over the settings from the LAN? (DHCP/DNS) thanks in advance
- Labels:
-
Wireless LAN Controller
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-27-2023 02:41 AM
You config internal dhcp
Do you enable dhcp proxy?
This need to make internal dhcp work in wlc.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-27-2023 05:46 AM
Big Thanks for your fast Replay. Yes, i have found the DHCP Proxy Settings in the Web GUI from the Controller (Advanced, Tab Controller). By this Way i see: if i ping on the DHCP Server from Controller, i get no response from the DHCP Server to the Controller. DHCP for LAN works fine. I connect the WLAN Controller over my LAN (the controller have a static IP in the same Network/Subnet as the DHCP Server.
DHCP Server 192.168.100.1
Cisco WLAN Controller 192.168.100.20
first Cisco AP have 192.168.100.111
Hint: we took over the hardware from the previous tenant. I don't have any documentation from the network. And, I'm a "newbie" to Cisco
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-27-2023 06:06 AM
Can you share screen shot of dhcp config
MHM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-28-2023 01:55 AM
Good Morning,
sorry4delay ... i must switch my workplace. the cisco setup in new rooms ....
here are my shotz
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-28-2023 06:47 AM
with these settings I (unfortunately) do not get an IP address assigned in the WLAN
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-28-2023 09:37 AM - edited 11-28-2023 09:38 AM
I only see mgmt interfaces IP where is wlan IP?
MHM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-28-2023 06:42 AM
Strange?! - i get a eMail
Hello mstyx,
Your topic recently received a reply .
But, I don't see an answer?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-28-2023 09:33 AM
If the reply was SPAM or malicious or off topic it would have been deleted by the moderators @mstyx
Please click Helpful if this post helped you and Select as Solution (drop down menu at top right of this reply) if this answered your query.
------------------------------
TAC recommended codes for AireOS WLC's and TAC recommended codes for 9800 WLC's
Best Practices for AireOS WLC's, Best Practices for 9800 WLC's and Cisco Wireless compatibility matrix
Check your 9800 WLC config with Wireless Config Analyzer using "show tech wireless" output or "config paging disable" then "show run-config" output on AireOS and use Wireless Debug Analyzer to analyze your WLC client debugs
Field Notice: FN63942 APs and WLCs Fail to Create CAPWAP Connections Due to Certificate Expiration
Field Notice: FN72424 Later Versions of WiFi 6 APs Fail to Join WLC - Software Upgrade Required
Field Notice: FN72524 IOS APs stuck in downloading state after 4 Dec 2022 due to Certificate Expired
- Fixed in 8.10.196.0, latest 9800 releases, 8.5.182.12 (8.5.182.13 for 3504) and 8.5.182.109 (IRCM, 8.5.182.111 for 3504)
Field Notice: FN70479 AP Fails to Join or Joins with 1 Radio due to Country Mismatch, RMA needed
How to avoid boot loop due to corrupted image on Wave 2 and Catalyst 11ax Access Points (CSCvx32806)
Field Notice: FN74035 - Wave2 APs DFS May Not Detect Radar After Channel Availability Check Time
Leo's list of bugs affecting 2800/3800/4800/1560 APs
Default AP console baud rate from 17.12.x is 115200 - introduced by CSCwe88390
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
12-04-2023 01:31 AM
OK, solved....
we use other HW
