Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Hi everyoneI enabled in my infrastructure WLC 9800-40 in HA mode (sso). Now i preparing configuration for AP, i will use only one model AP (Catalyst 9136I) so i added new IP scope (for AP) in infoblox with option 43 where i added hex value witch IP p...
I'm trying to setup my 9800 WLC to use DNA Center Application visibility features and AI Enhnaced RRM. At this moment, we need to disable telemetry to enable it again in some additional types of policy profiles (Guests and Flex), as I only performed ...
I have cisco wireless controller 5760 and approx 100 Cisco AP K9 170I is connected but few days sometimes we are unable to connect wifi. Only show obtaining ip address and some time connect automatically but if I put static ip then it is working. Cou...
how to tip over all APs at once command i CLI to new controller via High Avalibility
Resolved! Wi-Fi 6E Channel Scanning
When I go into the dashboard to configure 6E, I get the opportunity to set the channel width to 20, 40, 80 MHz, etc but the default is 80MHz wide and the PSC are only every 4th channel. That's fine if I'm using 80MHz channels, my AP will scan the PSC...
i have an existing network of 1850i access points with Mobility Express. Can i add 240AC access points to the same VLAN? Can they coexist in the same VLAN, or even join to each other?
Like the title, I'm using wireless Whenever the ap reboots, the wireless connection doesn't work immediately. If you reset the SSID or unplug and plug in the USB adapter, the connection will be random and normal. Does anyone have similar experiences?...
Upgrading Wireless network from 8500 to 9800.Both have to run in parallel till APs are replaced8500 is the RF leader, both WLCs in the same RF Group in the same subnet and in mobility.Tested roaming between wlcs, seem to work no issue.Have a couple o...
Good day!Need help in our WLC setup. We have a flex connect site. I have a 9800 WLC and 9210 AP that I am setting up so far. Service Port is enabled for OOB mngmt, and 0/1/0 is trunked for all VLAN traffic. The WLC is setup on the same VLAN as the AP...
Hello,I know not strictly a Meraki question but im pulling my hair out trying to find a wifi bridge and hoped someone here would be able to recommend one (disclaimer, if Meraki sold a Bridge, id buy it).I have gone through ubiquiti's website trying t...
Resolved! MAC address in catalyst controller
I dont see any option 9800 catalyst controller for MAC address filtering in an SSID. The method mentioned in this link not working, while select the auth list in SSID settings list does not shows up. https://www.cisco.com/c/en/us/support/docs/wirele...
AIR-CAP2702I-E-K9 40 AP are online in production running on an old AIR-CT5508-K9 we want to migrate them to an new controller Cisco Catalyst 9800-L Wireless Controller 17.9.5 but we cant see how they get there info of the old controller so we can tip...
Resolved! 9124AXE AP PoE out port configuration
hi, I have AP 9124AXE AP registered with WLC 9800. it will be connected to Fibre cable and powered via powered injected. i can't find any documentation of wlc9800 to configure POE out port of AP9124AXE, so that a PoE CCTV can be connected and a vlan ...
Hello we have a local 9120axi AP with a 9800LC WLC that seems to be losing connection. The AP is in flex connect, all config looks fine: AdvancedCountry CodeUS Multiple CountriesUSStatistics Timer180CAPWAP MTU1485AP Link LatencyEnabledAP PMK Propaga...
Hi everyone, I Had an issue with MR device. The MR device goes to offline. After Hard reset connection back to online, but there are some issues. - The AP can't setup static IP even I have changes to static but on the status IP doesn't change and kee...
