there is no communication between router and ap modules. router 881GW with embedded AP
I have router c881GN w/ embedded AP but I cannot ping AP from router and vise wersa. Could you suggest what is wrong with router & ap modules configurations bellow?
vlan 7 name APMGR
interface wlan-ap0 description Service module interface to manage the embedded AP ip unnumbered Vlan7
interface Wlan-GigabitEthernet0 description Internal switch interface connecting to the embedded AP switchport trunk native vlan 7 switchport mode trunk no ip address
interface Vlan7 description -= ip for AP management =- ip address 10.1.1.1 255.255.255.252 !
embedded ap: ++++++++
dot11 ssid a81m-guest vlan 2 authentication open authentication key-management wpa version 2 wpa-psk ascii 0 supper-pupper-password@!
interface Dot11Radio0 description -= outside WBR 2 management AP =- no ip address no ip route-cache ! encryption vlan 2 mode ciphers aes-ccm ! ssid a81m-guest ! antenna gain 0 speed basic-1.0 basic-2.0 basic-5.5 basic-11.0 basic-6.0 basic-9.0 basic-12.0 basic-18.0 basic-24.0 basic-36 .0 basic-48.0 basic-54.0 m0. m1. m2. m3. m4. m5. m6. m7. m8. m9. m10. m11. m12. m13. m14. m15. power local cck 15 power client 20 packet retries 24 drop-packet station-role non-root beacon period 101 beacon dtim-period 1 world-mode dot11d country-code CA outdoor no cdp enable bridge-group 1 ! interface Dot11Radio0.2 encapsulation dot1Q 2 no ip route-cache bridge-group 2 bridge-group 2 spanning-disabled bridge-group 2 block-unknown-source no bridge-group 2 source-learning ! interface GigabitEthernet0 description the embedded AP GigabitEthernet 0 is an internal interface connecting AP with the host router no ip address no ip route-cache ! interface GigabitEthernet0.2 encapsulation dot1Q 2 no ip route-cache bridge-group 2 bridge-group 2 spanning-disabled no bridge-group 2 source-learning ! interface GigabitEthernet0.7 encapsulation dot1Q 7 native no ip route-cache bridge-group 1 bridge-group 1 spanning-disabled no bridge-group 1 source-learning ! interface BVI1 ip address 10.1.1.2 255.255.255.252 no ip route-cache
interface BVI2 ip address dhcp no ip route-cache ! ip default-gateway 10.1.1.1
bridge 1 protocol ieee bridge 1 route ip bridge 2 protocol ieee bridge 2 route ip
both router and AP modules boot w/o erors, inerfaces vlan7, Wlan-Gig0 and wlan-ap0 are UP/UP
AP and router modules can ping itself but NOT eachother:
AP +++++++++ gate-ap#ping 10.1.1.2 re 3 Type escape sequence to abort. Sending 3, 100-byte ICMP Echos to 10.1.1.2, timeout is 2 seconds: !!! Success rate is 100 percent (3/3), round-trip min/avg/max = 1/2/4 ms gate-ap#ping 10.1.1.1 re 3 Type escape sequence to abort. Sending 3, 100-byte ICMP Echos to 10.1.1.1, timeout is 2 seconds: ... Success rate is 0 percent (0/3) gate-ap#
gate#ping 10.1.1.1 rep 3 Type escape sequence to abort. Sending 3, 100-byte ICMP Echos to 10.1.1.1, timeout is 2 seconds: !!! Success rate is 100 percent (3/3), round-trip min/avg/max = 1/1/1 ms gate#ping 10.1.1.2 rep 3 Type escape sequence to abort. Sending 3, 100-byte ICMP Echos to 10.1.1.2, timeout is 2 seconds: ... Success rate is 0 percent (0/3) gate#
logs for both modules don't have any related info.
I have a test network with a Cisco 2504 WLC and 1142N access points. I am just beginning to study for the Wi-Fi certification. I have a connection to 2504 WLC. AP is joined to WLC. When I connect to the Wi-Fi, it says, "connected without internet".I am ne...
Hi I have a guest SSID with CWA configured on a C9800 with AP9115AX and i want to override all DSCP Values to 0 for all packets to and from the wifi clients.i have tried a lot of configurations and a can drop traffic or shape traffic based on ACL or ...
We are pleased to announce the immediate availability of the IOS-XE release 17.4.1 for the Catalyst Wireless Controllers. The new code is now posted on the CCO and can be found at this link:
Table of Contents
The purpose of this document is to provide step-by-step instructions regarding how to connect your read-only Catalyst 9800 WLC or AireOS WLC with Cisco DNA Center for Assurance monitoring through manual configuration. I...
Securing devices without 802.1X
PSK (Pre-Shared-Key) WLAN is widely used for consumer & enterprise IoT onboarding as most of IoT device doesn’t support 802.1X. While PSK WLAN provides an easy way to onboard IoT, it also introduces challenges as...