10-30-2014 05:01 AM - edited 07-05-2021 01:50 AM
I have just installed new equipment on a site.
2 buildings have there connection using a wireless bridge
This wireless bridge consists of 2 x 2602 Autonomous AP's.
Switch 1 <--> AP1 << wireless >> AP2<-->Switch 2
AP1 is configured as follows:
dot11 ssid WGB
vlan 10
authentication open
authentication key-management wpa version 2
infrastructure-ssid
with also under de d0 interface
station-role root
infrastructure-client
AP2
has the following configuration
dot11 ssid WGB
vlan 10
authentication open
authentication key-management wpa version 2
infrastructure-ssid
and under de d0 interface the command
station-role workgroup-bridge
I can ping AP2 from Switch1 but i cannot ping Switch2 from Switch1.
From AP2 i can ping Switch1, AP1 and users in VLAN 10 also i can ping Switch2 from AP2 so this seems to have full connectivity.
From Switch2 i can only ping AP2 ( it is directly connected)
Switch2 does learn the MAC addresses from all the clients connected to Switch1 but cant ping them(AP2 can)
10 1cde.a7b1.cf97 DYNAMIC Fa0/23
10 68b5.99f8.34d0 DYNAMIC Fa0/23
10 7a2b.cb41.cc89 DYNAMIC Fa0/23
10 f40f.1be7.13f9 DYNAMIC Fa0/23
320 000e.5835.0792 DYNAMIC Fa0/23
320 000e.5835.4088 DYNAMIC Fa0/23
320 000e.5836.51d4 DYNAMIC Fa0/23
320 0017.880a.ef89 DYNAMIC Fa0/23
320 1cde.a7b1.cf97 DYNAMIC Fa0/23
320 84b1.539e.5c81 DYNAMIC Fa0/23
The VLAN's used are VLAN10 & 320.
VLAN10 is used for the wireless bridge but also for the corporate network.
I checked the configuration a bunch of times and im really stuck.
I tested it in my lab and it seemed to work their, the only difference is that Switch2 is a different 2960.
Appreciate the help!
10-30-2014 10:19 AM
can you share the configuration of the port that AP2 is connected to on Switch2?
HTH,
Steve
10-31-2014 12:44 AM
The configuration of the port on switch2 is
switchport mode trunk
switchport trunk native vlan 10
The configuration is the same for switch1
11-05-2014 11:56 PM
Attached are the configs of the AP's and below the switchport config on both side's
Switch 1
interface GigabitEthernet1/0/24
description *** AP1 Uplink ***
switchport trunk native vlan 10
switchport trunk allowed vlan 10,320
switchport mode trunk
Switch 2
interface FastEthernet0/23
description *** AP2 Uplink ***
switchport trunk native vlan 10
switchport trunk allowed vlan 10,320
switchport mode trunk
11-07-2014 02:08 AM
Did some more testing today.
Was actually hoping it wouldnt work when i plugged it allin in the lab but it did function fine.
The only difference is Switch 2 in the lab is a Cisco 2960S 24PS-L running IOS
c2960s-universalk9-mz.122-55.SE5/c2960s-universalk9-mz.122-55.SE5.bin
At the site where it wasnt working Switch 2 was a 2960 24TC-L running IOS
c2960-lanbasek9-mz.122-50.SE5/c2960-lanbasek9-mz.122-50.SE5.bin
Unfortunately i cant test it with that exact IOS and hardware since i dont have that available.
But that shouldnt make a difference right ?
11-24-2014 02:47 AM
Topic can be closed have it working know with a different configuration the cause is still unclear.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide