Solved: Wism2 and Wism1 in the same Chassis

Abdelaziz EL ABDALLAOUI · ‎02-25-2013

Hi,

I w'll install one Wism2 into existing Catalyst 6509 running 12.2(17)SXF IOS version, and has Two other Wism modules (old generation)

Could advise witch IOS can support these three mixt Wism?

And can you tell me if I’ll configure the ports channel for the new WISM2?

Regards

Abdelaziz

Leo Laohoo · ‎02-25-2013

I've got WiSM-1 and WiSM-2 in the same chassis. Upgrade to SXJ versions and the WiSM-2 will configure it's own portchannel. The WiSM-1 port channel will also be automatically created.

View solution in original post

Scott Fella · ‎02-25-2013

Have you looked at the WiSM2 config guide? So you will need to run at minimum 12.2(33)SXJ

Note: Sup 720 software version 12.2.(33)SXJ is the minimum software required for operation with the WiSM2 controller.

http://www.cisco.com/en/US/products/hw/modules/ps2706/products_tech_note09186a0080b7c904.shtml

Sent from Cisco Technical Support iPhone App

-Scott
*** Please rate helpful posts ***

Abdelaziz EL ABDALLAOUI · ‎02-25-2013

Thanks Scott for your replay,

As I see at this documentation:

The Supervisor automatically creates a port-channel interface for the independent controller in the Cisco WiSM2

And how about the port channel configuration that already manually created for the existing WISM1 (old generation)?

I must to configure the port-cannel for these existing module or the Supervisor we’ll do also create them?

Best Regards

Leo Laohoo · ‎02-25-2013

I've got WiSM-1 and WiSM-2 in the same chassis. Upgrade to SXJ versions and the WiSM-2 will configure it's own portchannel. The WiSM-1 port channel will also be automatically created.

Abdelaziz EL ABDALLAOUI · ‎03-04-2013

I had installed the WISM 2 with success, using IPSERVICES 12.2(33)SXJ5 IOS, and all APs (CAP2602I) can join the Wism2.

But after this installation, some users can't connect in some areas.

In fact:

With the same Station I can connect in all other floors (about 10 floors), but not in the floor 4 and 8.

For your information I shut down the new WISM2, and so I can connect with my station in floor 4 and 8.

Do you have please idea to troubleshoot this issue?

Best Regards

George Stefanick · ‎03-04-2013

Are both WISMs in the sam mobility group ? Same config ?

__________________________________________________________________________________________
"Satisfaction does not come from knowing the solution, it comes from knowing why." - Rosalind Franklin
__________________________________________________________________________________________
‎"I'm in a serious relationship with my Wi-Fi. You could say we have a connection."

"Satisfaction does not come from knowing the solution, it comes from knowing why." - Rosalind Franklin
___________________________________________________________

Leo Laohoo · ‎03-04-2013

What error message are the users getting? Can you post the output to the command "debug client "?

Abdelaziz EL ABDALLAOUI · ‎03-04-2013

Please see as below :

In Wism 1:

*apfMsConnTask_0:

Mar 04 14:10:58.038

: %APF-1-PROC_RSN_WARP_IE_FAILED: apf_80211.c:2454 Could not process the RSN and WARP IEs.

station not using WPA or WPA2

on WLAN requiring WPA and/or WPA2.MobileStation:

7c:61:93:8b:4f:bb

,

SSID:XXXXXXXXX,AP: 00

Dot1x_NW_MsgTask_1: Mar 04 14:37:43.017: %DOT1X-3-MAX_EAP_RETRIES: 1x_auth_pae.c:3136 Max EAP identity request retries (3) exceeded for client 58:1f:aa:c9:ca:99

*Dot1x_NW_MsgTask_1: Mar 04 14:37:43.017: %DOT1X-3-ABORT_AUTH: 1x_bauth_sm.c:447 AuthenticationAboted for client 58:1f:aa:c9:ca:99

*Dot1x_NW_MsgTask_1: Mar 04 14:37:37.979: %DOT1X-3-ABORT_AUTH: 1x_bauth_sm.c:447 AuthenticationAboted for client 58:1f:aa:c9:ca:99

*Dot1x_NW_MsgTask_1: Mar 04 14:37:32.161: %DOT1X-3-MAX_EAP_RETRIES: 1x_auth_pae.c:3136 Max EAP identity request retries (3) exceeded for client 58:1f:aa:c9:ca:99

*Dot1x_NW_MsgTask_1: Mar 04 14:37:32.160: %DOT1X-3-ABORT_AUTH: 1x_bauth_sm.c:447 AuthenticationAboted for client 58:1f:aa:c9:ca:99

*Dot1x_NW_MsgTask_1: Mar 04 14:37:27.147: %DOT1X-3-AAA_AUTH_SEND_FAIL: 1x_aaa.c:597 Unable to send AAA message for client 58:1f:aa:c9:ca:99

*Dot1x_NW_MsgTask_1: Mar 04 14:37:27.123: %DOT1X-3-ABORT_AUTH: 1x_bauth_sm.c:447 AuthenticationAboted for client 58:1f:aa:c9:ca:99

*Dot1x_NW_MsgTask_5: Mar 04 14:35:47.956: %DOT1X-3-MAX_EAP_RETRIES: 1x_auth_pae.c:3136 Max EAP identity request retries (3) exceeded for client 58:1f:aa:95:6c:0d

*Dot1x_NW_MsgTask_5: Mar 04 14:35:47.956: %DOT1X-3-ABORT_AUTH: 1x_bauth_sm.c:447 AuthenticationAboted for client 58:1f:aa:95:6c:0d

*apfMsConnTask_0: Mar 04 14:10:58.038: %APF-1-PROC_RSN_WARP_IE_FAILED: apf_80211.c:2454 Could not process the RSN and WARP IEs. station not using WPA or WPA2 on WLAN requiring WPA and/or WPA2.MobileStation: 7c:61:93:8b:4f:bb, SSID:APHM-UTILISATEURS,AP: 00

In Wism 2 when ON :