Wireless

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

review


Labels

Forum Posts

How to recover and troubleshoot an AP that was changed to bridge mode and subsequently lost connection to the controller?  Tried toggling switch ports to force reboot, however unsuccessful.  Curious if there's a solution without having to manually ge...

wifiguy1000 by Community Member
  • 1910 Views
  • 6 replies
  • 0 Helpful votes

Hi,We just got a 2500 controller and three of the 1600 aironet access points. I have the controller setup but I can't get the access point to connect to it. I have tried plugging it in to the PC and it asks me for a username and password when I go th...

We see can create WLANs upto 16 but as I cannot create 2 same SSID. I wants to know if we can create 17th WLAN and how we can if, yes.As I see we can create upto 512 WLANs. One thing is we can disable the WLAN by default given in the controller and t...

I have about 60 AP's connected to my WLAN controller and want to migrate these to Flexconnect.  Do I have to manually changed each AP individually to FlexConnect or is there a way on the controller to configure them all in one easy way?  I plan to es...

I am looking to configure if, 5508 controller's ports particularly in different VLANs and pull cable from the port and put it in L3 to it's belonging VLAN ? and at the same time all the different SSID will work as usual our standard and best practice...

Dear Expert,Want to know.if we have 6 LW access points Two wlc 2106 and wlc 4402-50k Can we use both wlc as active and failover with 6 and 50 licenses.Jawad       

Dears,I want to do it:C3560 --- e0 / Root-AP / Radio0 ======== Radio0 / Non-Root AP / e0 --- CISCO7911 IPPhone --- PCConfig in C3560:switchport access vlan 10switchport mode accessswitchport voice vlan 100Root to Non-Root only connect via ONE SSID, n...

Hi,  Own two 5508 controllers operating in HA SSO. Became necessary to accomplish the change of addressing these. Both addresses will remain the same subnet, however the question arose whether to undo the HA configurations or is there a way to alter ...

igorromanluz by Community Member
  • 1449 Views
  • 5 replies
  • 0 Helpful votes

Sirs, Could someone please explain how switching occurs on a Flexconnect AP that doesn´t have its VLAN support tab filled in?Will it switch data over its default vlan, or tunnel back to the controller as in Local mode?I´ve been trying to gather this ...

Pedro Prado by Community Member
  • 792 Views
  • 1 replies
  • 0 Helpful votes

Experts, Assume  the below scnarioWireless Clent = 6000 all AC supportedAP = AC supported 3700 WLC = 55xx or 57xx ??5508 = 8 Gbps throghput5760 = 60 gbps throughput Which controller should i plan for this scnario and why? -Mukesh 

mukesh.patil by Community Member
  • 2286 Views
  • 3 replies
  • 0 Helpful votes

Hi,I've 37xAIR-LAP1252AG connected to 2x3750 PoE switches. Some of them (12xAIR-LAP1252AG) are not working properly. 1) On the same switch, the output of the "show power inline" is different whether the AP is reachable or not:**********************AP...

Hi, Spec says that 2600 series access-points are BYOD optimized. We are using 1600 for BYOD. I dont see any issue in the BYOD network. Anyone knows what additional features that 2600 got in BYOD support. thanks,Ramesh

Review Cisco Networking for a $25 gift card