cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
395
Views
0
Helpful
6
Replies

WLC can't detect LAP

WLC 5500 canr detect LAP1040 either in the same vlan or on different vlan . i attached the scenario and configuration on the file .

1 ACCEPTED SOLUTION

Accepted Solutions
Scott Fella
Hall of Fame Guru

Is the time setup properly on the WLC? As long as that is set and the country code matches between the AP and WLC the AP should join.

Can you post the output from the console of the AP after you power cycle the AP.

Sent from Cisco Technical Support iPhone App

-Scott
*** Please rate helpful posts ***

View solution in original post

6 REPLIES 6
Scott Fella
Hall of Fame Guru

Is the time setup properly on the WLC? As long as that is set and the country code matches between the AP and WLC the AP should join.

Can you post the output from the console of the AP after you power cycle the AP.

Sent from Cisco Technical Support iPhone App

-Scott
*** Please rate helpful posts ***

View solution in original post

first i didn't make any configuration on LAP to make it match country code i configured in controller . i just setup the time on controller and condry code and no configuration on LAP .

output from controller

Debug CAPWAP event

ARP entry for 0:0.0.0 to the network processor. entry does not exist.

*Jun 17 13:57:09.869: %DTL-3-NPUARP_ADD_FAILED: dtl_arp.c:2280 Unable to add an

ARP entry for 0:0.0.0 to the network processor. entry does not exist.

*Jun 17 13:21:48.709: %CAPWAP-3-DISC_INTF_ERR2: capwap_ac_sm.c:1525 Ignoring dis

covery request received on a wrong VLAN (230) on interface (1) from AP 4c:4e:35:

b3:e2:a0

*Jun 17 13:21:48.707: %CAPWAP-3-DISC_INTF_ERR2: capwap_ac_sm.c:1525 Ignoring dis

covery request received on a wrong VLAN (230) on interface (1) from AP 4c:4e:35:

b3:e2:a0

*Jun 17 13:21:38.466: %LWAPP-3-DISC_INTF_ERR2: spam_lrad.c:1555 Ignoring discove

ry request received on a wrong VLAN (230) on interface (1) in L3 LWAPP mode from

AP 4c:4e:35:b3:e2:a5

*Jun 17 13:21:38.464: %LWAPP-3-DISC_INTF_ERR2: spam_lrad.c:1555 Ignoring discove

ry request received on a wrong VLAN (230) on interface (1) in L3 LWAPP mode from

AP 4c:4e:35:b3:e2:a5

You will not be able to change the country code on the AP as it is manufactured that way.  The only way is the way you did it, on the WLC.  So you did get it working?

One thing to note is if you have multiple country codes configured on the WLC, you need to look at this link created by Steve R.  The WLC will use the most common settings for each of the countries specified for channel and power.

http://nostringsattachedshow.com/2012/02/02/multiple-country-codes-with-the-cisco-wlc/

Thanks,

Scott

Help out other by using the rating system and marking answered questions as "Answered"

-Scott
*** Please rate helpful posts ***

  WLC:  sh sysinfo;

(Cisco Controller) >show sysinfo

Manufacturer's Name.............................. Cisco Systems Inc.

Product Name..................................... Cisco Controller

Product Version.................................. 6.0.199.4

Bootloader Version............................... 1.0.1

Field Recovery Image Version..................... 6.0.182.0

Firmware Version................................. FPGA 1.3, Env 1.6, USB cons

1.27

Build Type....................................... DATA + WPS

System Name...................................... Cisco_62:54:24

System Location..................................

System Contact...................................

System ObjectID.................................. 1.3.6.1.4.1.9.1.1069

IP Address....................................... 10.10.30.2

Last Reset....................................... Power on reset

System Up Time................................... 0 days 2 hrs 18 mins 0 secs

System Timezone Location.........................

Current Boot License Level....................... base

Current Boot License Type........................ Permanent

Next Boot License Level.......................... base

Next Boot License Type........................... Permanent

--More-- or (q)uit

Configured Country............................... EG  - Egypt

Operating Environment............................ Commercial (0 to 40 C)

Internal Temp Alarm Limits....................... 0 to 65 C

Internal Temperature............................. +38 C

External Temperature............................. +29 C

Fan Status....................................... OK

State of 802.11b Network......................... Enabled

State of 802.11a Network......................... Enabled

Number of WLANs.................................. 1

3rd Party Access Point Support................... Disabled

Number of Active Clients......................... 0

Burned-in MAC Address............................ 00:06:F6:62:54:20

Power Supply 1................................... Present, OK

Power Supply 2................................... Absent

Maximum number of APs supported.................. 25

2.  WLC:  sh time;

(Cisco Controller) >show time

Time............................................. Thu Jun 20 12:07:02 2013

Timezone delta................................... 0:0

Timezone location................................

NTP Servers

    NTP Polling Interval.........................     86400

     Index              NTP Server

    -------  --------------------------------

about

3.  AP:  sh version; and

4.  AP:  sh inventory

  when i connect console to LAP there is no any output from console , i think because it make restart every time

Product Version.................................. 6.0.199.4

AP1040 is supported from WLC firmware 7.0.98.0.

You need to upgrade the firmware of your WLC.

Scott Fella
Hall of Fame Guru

There is always output from the AP... You should see it booting. Make sure you have your serial port setup for 9600, 8, none, 1, no flow control.

Sent from Cisco Technical Support iPhone App

-Scott
*** Please rate helpful posts ***
Content for Community-Ad