Activity in DevNet
A lesson for anyone starting network automation: stay read-only first
After a few years doing this, the biggest thing I'd tell anyone starting out isn't which tool to pick. It's to resist pushing config for as long as you can.Almost every early win is read-only anyway. Pulling show output, backing up configs, checking ...
ACI Exporter: APIC returns no data for interface traffic/drop stats
Hello Cisco DevNet Community,We are currently deploying the `opsdis/aci-exporter` to collect Cisco ACI metrics through APIC and expose them to Prometheus/Grafana.The general exporter setup is working. We can successfully collect and visualize several...
Resolved! API rate limiting on Meraki dashboard limiting our scale.
We have more that 1000 sites/networks on Meraki and we have automation via API for various admin tasks. Since March this year we noticed that API calls are rate limited to a point where 1 API call per 10s still triggers rate limiting. Are there plans...
Umbrella automation
Hi,I'm looking to further automate our Meraki MX automation for the Umbrella settings.Right now, there very little in the official API : only enough to link the MX to the Umbrella dashboard.In the early access API we can activate the protection (ther...
Error API Response Received from Finesse for Silent Agent Monitoring
Hello,We are encountering an issue with a specific supervisor in UCCX when attempting to perform silent monitoring. The Finesse API is returning the following error:FinesseController::MakeSilentMonitorCallCommand FailedCisco TAC has reviewed the UCCX...
Resolved! ACI APIC Simulator Always-on - Host unreachable
Hi Everyone,Trying to access https://sandboxapicdc.cisco.com for the ACI APIC Simulator, but it is not responding and Sandbox status says "host unreachable". It was doing fine yesterday.ACI Simulator Always-On -20260612T11081548.Between 09:00 and 11:...
Meraki Lab Not Spinning up
Hi team,Hope you're doing well. I wanted to flag an issue I ran into while trying to spin up the Meraki sandbox.The environment failed to launch in Torque, with this message:I tried to spin it up three times this afternoon (June 14, 2026) and all thr...
API - Wrong scope ? getOrganizationDevicesMemoryByDevice
Hi ,To whom ever reads this ( hi Oren )Is this expected that this call getOrganizationDevicesMemoryByDevice is named like a org-wide call but needs a specific networkId ?Whenever I see a getOrganizationXYZ call , I never expect to specify a network....
How Automation Is Changing Traditional CLI-Based Networking Jobs
I started learning networking through the CLI, I used to think that being a good network engineer meant knowing hundreds of commands by heart. And to be fair, CLI skills are still important. You need to understand routing, switching, troubleshooting,...
DHCP Pool Usage Inconsistency Between Dashboard and API Response
Hi everyone,I'm reporting an issue where the DHCP pool usage data shown on the Meraki Dashboard does not match the data returned by the API. This inconsistency is causing problems for our automated network monitoring workflows.
SSH timeout - Catalyst 9000 Always-On Sandbox
Hi All,after starting VPN I cannot reach the IP Address 10.10.20.181 of the Cat9k via SSH. Ping also does not work. VPN is up and routing table looks fine. Any ideas?(Cat9300-20260609T14105380)
Versioning and Production for Workflows
Currently, I might go through several different versions of a workflow or atomic. Is there a best practice or a way to do versioning? Since there is no undo button for removing elements, I have become much more judgmental about how to implement certa...
Resolved! XDR Initial Response - Secure Endpoint Scan
As part of an initial incident response, I would like to run a full scan from a secure endpoint. Although I searched, I do not see this in the API documentation showing this as an option at the moment.Is there a different way to approach this, or is ...
Resolved! XDR Automation Rule targeting Detections
Automation Rules can target many things, but I would like to use detections as targets rather than incidents, as not all detections are raised to incidents. From the detection alone, there might be certain actions I would like to take. If detections ...
ACI APIC Simulator Always-on - Host unreachable
Hi Everyone,Trying to access https://sandboxapicdc.cisco.com for the ACI APIC Simulator, but it is not responding and Sandbox status says "host unreachable". It was doing fine yesterday.Sandbox: ACI Simulator Always-On -20260609T23133901. Tried June ...
| User | Helpful Count |
|---|---|
| 7 | |
| 4 | |
| 4 | |
| 1 | |
| 1 |
