Hi all,I configured the following on the ACE module:object-group network test host 192.168.1.21 host 192.168.1.22 host 192.168.1.23object-group service port tcp eq www tcp eq 8080access-list T line 8 extended permit object-grou...
Hi all,I configured the following on the ACE module:object-group network test host 192.168.1.21 host 192.168.1.22 host 192.168.1.23object-group service port tcp eq www tcp eq 8080access-list T line 8 extended permit object-grou...
Good day,ACE version A2(3.6) is no longer available on CCO. Replaced by A2(3.6a). I have two questions:1. Is version A2(3.6) a problematic version? If so, suggestion is to implement A2(3.6a) or revert to version A2(3.5)?2. If ACE version A2(3.6) is O...
I have configured snmp as above on the Central manager, and went into the device GUI and configures notifier ( for email alerting) but I am not getting any email alerts. The alarms are there if I check on Central manager and on the...
Hi networker,Actually, I'm beat me about configuring the ACE 4700!I've read the cisco configuration guide but it is difficult to put all the configuration together! I don't find right example....I'm trying to configure "Basic Load Balancing Using Bri...
Hi,First post, so bear with me.I have a 11501, which is connected via it's Gigabit port to a Nexus 5010 switch. This in turn services hosts which have two VM's, set up as web application servers.Config is as follows:!*************************** GLOBA...
Every 3 hours we are receiving a warning message stating that "The device is about to disconnect from the network" and then roughly 10 mins later the message states "The device is operational and ready to partcipate in the network". I can't seem to ...
I know that it's possible on the CSS to handle multiple incoming HTTP requests that terminate on the same IP address and port and balance them to various servers based on the url. For instance, I can set up www.cats.com and www.dogs.com at the same...
Hi to all,I need to balance some servers in same network and same VLAN of cisco ace and servers has configured a loopback interface with Virtual IP configured IP.In logical way configuration is following10.168.200.250 -- ACE -- Server1 (lo0 - 10.168....
I got below configurations.!************************** SERVICE **************************service server1 protocol udp port 22015 ip address 172.20.117.71 active !*************************** OWNER ***************************owner com content r...
Hello This alarm comes and goes on one of our WAAS devices. It just started happening. I'm running version 4.4.1. Model is WAE-674.The # of active CIFS connections are only 46. What does it mean and what can I check when it shows up?RAID Physical dis...
Currently migrating over from our CSS to the new ACE and I have a few questions re: SSL certs and VIPSAll of our inbound SSL connections terminate on the CSS and redirect a backend HTTP request to an internal server.Right now we URL match on the inc...
Hello,I have a data centre WAE-574 using WCCP redirect. Behind a firewall I have the CM. In a remote location, +/- 600ms RTT, I have another WAE-574 in line mode. This was working perfectly until it was powered off. It lost all its config on recovery...
Our ACES authenticate to an ACS server VIA TACACS when going to CLINow that I have ANM set up..i can make changes to the ACES when using the default admin account in ANM(ANM is also configured on the ACS)However I am now trying to set up different us...
Hello,I have a data centre WAE-574 using WCCP redirect. Behind a firewall I have the CM. In a remote location, +/- 600ms RTT, I have another WAE-574 in line mode. This was working perfectly until it was powered off. It lost all its config on recovery...
How can you check if balance ACA is enabled in CSS11503? How can you see also if the content switch(CSS11503) is load balancing using balance ACA? "show load" command does not show it.xxxxxx# show load Global load information: Reporting:Enabled ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
03-06-2024 12:27 PM | ||
02-21-2024 04:21 AM | ||
10-04-2022 06:16 AM | ||
09-26-2022 11:58 AM | ||
09-13-2022 02:40 AM |