Application Networking

<p>Hello:<br />Is there any way to achieve the next config but for ACE Module?<br /><br />CSM_1:<br /><br />probe HTTPS tcp <br />interval 5<br /> failed 10<br /> open 5<br /> port 443<br />serverfarm REDIR1<br /> nat server<br /> no nat client<br />...

Hello After a few days of working fine the systems stopped answering SNMP and then the CLI began having problems with some commands. The easiest to see being "show running-config". At this point it shows nothing. It just waits and does nothing. I hav...

HiI have a customer who requires the load-balancing predictionalgorithm to be based on the CPU level of the Server. So the server with the least CPU is chosen at the laod-balancing stage.Is there a way to do this?Thanks James

<p>Greating</p><p>I have setup load balance for 4 jave servers in same solaris 10 zone. I found that looks like most sessions go to first jave server only.</p><p>The configuration is:</p><p>  content multijave<br />    vip address 10.1.1.131<br ...

Hi,I am using ACE4710 with all the servers in default admin context. Now i need to enable sticky persistence and for this it asks me for resource allocation. I've couple of questions regarding this:1- can i allocat sticky resources to default resourc...

HI,Just looking for a bit of advise on an issue that has started to show up on a set of ACE10-6500-K9 blades we have installed.The ACE's is running Version 3.0(0)A1(6.1).They have been up and running for about 18 months now with no issues at all, the...

I am working on a CSS to ACE migration, and as the first step of testing, we have moved both the CSS and ACE running in parallel with different IP addresses. As a test, we changed the default gateway of 2 servers to point to the ACE. From the ACE, ...

Hello,I have a requirement to redirect https traffic to http. Is it possible to do that in the CSM? In the CSM documentation all redirect examples/config etc refer only to http traffic so I am wondering if the other way around is supported as well.BT...

I have a brand new WAE512 with no inline card plugged in. During bootup, it says "operating system not found". I then tried a 4.0.9 Recovery CD. At the Installer Menu, I selected "install image from cdrom". But the message came up as "no Flash detect...

I have 3 VIP's setup on an ACE 4710 Appliance and they are all working correctly. 2 of them I can ping and get ICMP replies back the 3rd (also the busiest) I dont get ICMP replies back. The config is identical between them all as far as adding in t...

HiSince WCCP has been enabled on the 3750's there has never been the WCCP option to "ip wccp redirect exclude in" from the WAAS unit to stop Loops. Is there any way round this or is the only option to configure PBR on the 3750.ThanksIan

Hi, I am unable to authenticate via Radius, the ACE server does not even see an attempt by the module. The following is my config in the Admin context:radius-server retransmit 3radius-server host 10.9.48.135 key 7 "*****" auth-port 1645 authenticatio...

I have had a customer raise an issue with me. Unfortunately I am not too hot on the CSM.Switch Type - Cisco WS-C6513IOS VSN - 12.2(18)SXF4CSM Module detailsCard Type - SLB Application Processor ModuleModel - WS-X6066-SLB-APCHardware VSN - 1.8Software...

Hi,I am asking me if it is possible to load sharing traffic itend to a vip with two serverfarm.I would like to have two serverfarm active no active/backup for my vip. Thanks for help.Regards.