Heads Up :
The post you are writing will appear in a public forum. Please ensure all content is appropriate for public consumption. Review the employee guidelines for the community here.
Hi All, We have 2 Bluecoat proxy appliances connected to CSS , Is it possible to confgiure WCCP on CSS for this setup ? Our requirement is to act CSS as a transparent proxy server for internet access ? Please advice if it possible or not ..
We have two iPrism Proxy appliances that we are trying to load balance for failover purposes. We have tried simple layer 3 balance rules. It appears that our proxy request are being passed to the iPrisms and the Proxy is connecting to the Internet ...
We are replacing CSS with ACE. --------------CSS_Config--------------service apps1 ip address 10.4.11.1 range 3 keepalive type http keepalive frequency 15 activeservice apps2 ip address 10.4.12.1 range 3 keepalive type http keepalive frequency...
I have a Catalyst 6500 with an ACE and Firewall Service Module (FWSM) installed. See Diagram.The server sits in VLAN 10 which is configured in both ACE and FWSM. The server load balancing is configured in DSR mode (Direct Server Return) which means t...
I am trying to determine the best way to monitor the health of my servers. I have multiple Web Server instances running on different ports on the same physical server. So I have configured 1 RSERVER. In my Server Farm configuration I specify the RSER...
Do resources get consumed on 'flow permanent' flows, even when the referenced TCP connection is closed by a client or server? I do not see our CSS 'accumulating' any permanent flows even though we have some set.Appreciate your insight. The book says...
users should able to access "http://virtual IP on the CSS/app/login.jsp", and on my CSS, I want to change to http keepalive from default ICMP, here is my config:service Server2 ip address 10.122.49.18 keepalive type http keepalive port 80 kee...
Hi,Sorry for the newbie question.Is there any way to attach two or more keepalives to one service on CSS.I need to monitor two ports on one servivce. And if one of these prots fails i need to bring service down.For example something like this:service...
Hi,when I tried to move one of my rserver from existing serverfarm to another serverfarm, URL is not working. if i am reverting backto same serverfarm where it is working fine. then its working fine.Regardssateesh
There are multiple VIPs, 192.168.0.252 (HTTP/HTTPS) and 192.168.0.248 (FTP/SFTP) that work.A new VIP, 192.168.0.250 does not properly work for HTTP/HTTPS. Behind this VIP there are two servers: 192.168.0.25 and 192.168.0.27. In the load balancer GUI,...
Hi All,I have 2 server behind a CSS one is a windows and the other one is a Solaris, both of them given the same service through the same content, and both in the same source-nat-group, both servers need to do traceroute to the internet, the windows ...
I know I saw it here some time ago, but can't find it. On the CSS 11500 series, version 08.20.2.01, there's a script to sync between the two boxes setup for redundancy. Can anyone let me know how that's done again>Thanks in advance.Jim
As part of high availability configuration we are implementing GSS for site selection for the services behind CSS.CSS checks service availability by keep alive.GSS need to function based on the service availability status in CSS. How can this be achi...
I have implented WAAS between sites over our WAN and I am also implementing QOS. I am looking for advice on a situation I am having with policing NetApp traffic where WAAS is implemented. In source site "A" I have some NetApps off an LAN interface ...
Hi :We are using Cisco CSS 11503 for few years. We recently noticed that the users complaint the slowness in the application and session timeout. We increase the flow-timeout and the session can take longer but there is still slowness exist. If the u...
