Application Networking

I am testing our new CSS 11501s (which are going to replace our old LocalDirectors), and have setup a little lab like so:Test PC|Router|| e5CSSe1 e2| |Srv1 Srv2I cannot seem to get the configured vip addreses to work, however I can connect to the act...

Hi,New to this Forum, at least. Apologies if this is not appropriate for SLB questions...We have a standard IOS SLB setup with 2 x Cisco3725's running HSRP. IOS SLB setup for a few servers on private LAN. They're running www, ftp, https.We have a cus...

I trying to do AAA accounting for commands using a Content Engine CE-560 (ACNS 5.2.3 build b9) and Cisco Secure ACS (v3.1(1)build 27).I have de following configuration:tacacs key <encrypted>tacacs host 10.20.250.200tacacs host 10.10.250.200 primary!!...

Hey everyone.Does anyone have any experience working with the LDAP protocol and making policy decisions based on the content within LDAP queries?I was reviewing the CSM gear available to me and it would seem that I can do this for the HTTP protocol n...

Hey everyone. Can someone tell me what the proper image is for IOS on a 3845 so that I might do SLB? I loaded 12.4-1a (Advanced Enterprise) on my box and the gear isn't there (ip slb). I am starting to worry that possibly the ip slb stuff is only ava...

Hi, I'm interested in what type of performance measurement MIB others are polling to determine the performance of their CSS? We have a basic CSS setup, sitting in front of multiple Web servers. Thanks

Has anybody tried using ospf advertise command to inject vip into ospf? I have tried this on both 7.4 and 7.5 with no success. The vip appears in the ospf lsdb on my CSS (not in IP routing table tho)but not in my 6500 lsdb directly connected on the v...

Hi,just two questions in regards of load balancing:1) Does the advanced-balance ssl notice if an sslid change is done in the SSL-Session (some clients reinitiate a session after some time)? 2) Is the sslid-stickiness aware of 1) and keeps the connect...

I have an Local Director 417 with one virtual ip and 4 servers served by the virtual ip. The LD 417 is currently operational.If I change the virtual ip using the command "ip address 10.10.10.3 255.255.255.0", will the command be effective right away ...

I am trying to get my SSL module up and running. When I do a show ssl-proxy service I see:Admin Status: upOperation Status: downProxy status: No Client VLAN, No Server VLANI have an admin and server vlan configured on the SSL module and trunked on th...

Hi,We are evaluating a CSS 11500 and try to configure url path rewrite and NAT, but we have some problems.What we would like to do is the following:http://www.example.com/path1 -> http://host1:80http://www.example.com/path2 -> http://host1:8080http:/...

Hi,our customer wants to set up the following configuration :switch----------switch | |CSS1----FE-C/O----CSS2 | |switch----------switchAll interfaces, except the FE-Crossoverlink for redundancy-protocol, are in the same VLAN.I think we have a spannin...

Hi,Someone could explain what does this msg below means?JUL 1 10:25:44 1/1 15651 IPV4-7: Ipv4MasterForwIphdrChk: bad/unsupported IP protocol received (50). Dest = 200.2xx.2xx.1, Src = 200.212.31.2thanks in advance,Renato

I have a webserver to receives traffic on port 4080. The firewall is configured for this only. I want to redirect traffic to say port 8080. Is there a way to do this on the CSS? I've looked at SSL redirect examples and this requires that I open this ...