Application Networking

Hi,I have two CSS11050 running WebNS 6.10 Build 405.I'm using the eth-management interface for SSH and HTTPS remote access (I have configured an ip management route toward my management network) Everything is working fine, but I noticed that the CSSs...

Hi Friends,I´m freshman with Content Technologies.I'm a little confused about how it works.I have the follow enviroment: four CE566 used to root CE fuction. ( tree for balance e one for backup ). two CE566 used to CDM function ( active and backup ) ...

We have configured the CSS for content rule-based DNS operation for GSLB. The CSS are installed behind a firewall. CSS are configured with private addresses for the services and the VIP. This VIP is translated at the firewall for external access.In t...

Hello all,I have configured my 6500 as per Gilles advice (topic CSM and FWSM), and something strange is happening. I can access the servers directly, but not via VIP (I can ping the VIP). This is a 6513 with one CSM and one FWSM. There are interface-...

I have a stand-alone CE-590 connected to 72xx ISP router,located outside of our PIX. When WCCP service is enabled, download speed (tested using DSLExtreme site) is about 11MB, but if WCCP is disabled (or simple unplugged cable from CE), then download...

I have a CSS with a SSL module performing GSLB and load balancing b/w backend web servers. From a DNS perspective, the IP address of the primary site is always given out unless the primary site is down. I am having problems with users being asked t...

Hi,I find on the Packet Online the folowing question and answer:Q: I will have a server farm with identical Web application servers and will be running SSL for data protection. Can the Cisco CSS 11501 without SSL termination load balance SSL Web appl...

Hi Guys,When i did a 'show statistics http request' , my 'Failures from Outgoing Proxy' is always increasing. Whats the problem and how can i resolve it because i couldnt find any solution documented on the website.Troubled,Kelvin

No one at our location is familiar with the Cisco Content Devices and we have a CE 590. The intended use of the device is to pass wccp requests from a 7204 router to Websense, it is also supposed to be configured for caching.However, I don't think so...

This is a new installation using WCCP v2. Even though the engine is registered with the IOS router and the router is definitely forwarding traffic to the CE, no disk space is being utilized at all and my savings is reported as 0. I've verified that t...

Hello,Got 2 CSS in VIP redundancy and a critical-server script that’s pinging up and downstream routers off active CSS.If the SSL module fails, will the backup CSS takes over?Configuration of our CSS is very basicservice ssl_module1 type ssl-accel ...

HI All...A quick check if whether you all have encountered this as i'm quite new to CSS.I currently have this setup with 2 servers (10.0.0.99 & 100). And i have a NTP server on another segment outside the CSS, i wish to time sync these 2 servers with...

HI,I've to do loadbalancing based on parts of the URL.The URL will look like this:www.myserver.com/a/b/c/d/x=12345/bdc/*.htmIf the x=<digits> is includes I've to use server1-3 1 if the x is not included I've to use server 4-6I can right now think of...

I have run into a situation, we just upgraded to version 7.50.004 of WebNS, and SNMP traps no longer can get to the destination address. I did a sniffer capture, and the traps are being sent from the VLAN 1 IP address, even though we have a source sp...

Hi.I'm gonna setup CE-7300 to filter specific ip address. some users don't connect to the internet because of filter on CE-7300.So I had config CE-7300 by using filter funciton with smartfilter.But the thing is, I had too many filter ip address about...