09-05-2012 06:52 AM
Guys,
I would like to know if allowing vlans under portchannel will replicate on standby unit.Somehow I see all configuration is sync except switchport trunk allowed vlan under Portchannel.
Thanks
Ajay
09-05-2012 09:48 AM
Hi Ajay,
Are you sure the running config is in sync? This should replicate and the config should be in sync.
-
Siva
09-05-2012 10:49 AM
Yes Siva running config is in sync.
However i found on switch where standby ace is connect port channel config has got 3 ports but 3rd physical port is not connected.
Even in that case why rest of config goes to standby unit except port channel allowed vlans.
I am going to remove that 3rd unused port from port channel to see if that solve my issue.
Thanks
Ajay
09-06-2012 03:56 AM
Hi Siva,
I remove 3rd port from port channel but still vlans are not getting sync.
ACE1/Admin# sh vlan
Vlans configured on physical port(s)
vlan3001 vlan3060 vlan3200-3201 vlan3208 vlan3260-3262 vlan3264-3265 vlan3270-3272 vlan3274-3275 vlan3280 vlan3300-3302 vlan3650-3652 vlan3661-3663 vlan3668-3669 vlan4090
ACE1/Admin#
ACE2/Admin# sh vlan
Vlans configured on physical port(s)
vlan3001 vlan3200-3201 vlan3208 vlan3260-3262 vlan3264-3265 vlan3270-3272 vlan3274-3275 vlan3300-3302 vlan3650-3652 vlan3661 vlan3668-3669 vlan4090
ACE2/Admin#
ACE1/Admin# sh ft group status
FT Group : 1
Configured Status : in-service
Maintenance mode : MAINT_MODE_OFF
My State : FSM_FT_STATE_ACTIVE
Peer State : FSM_FT_STATE_STANDBY_HOT
Peer Id : 1
No. of Contexts : 1
Running cfg sync status : Running configuration sync has completed
Startup cfg sync status : Startup configuration sync has completed
ft peer 1
heartbeat interval 300
heartbeat count 10
ft-interface vlan 4090
query-interface vlan 3001
ft group 1
peer 1
no preempt
priority 150
associate-context Admin
inservice
any suggestion/ next steps to troubleshoot ?
Thanks
Ajay
09-06-2012 04:52 AM
Hi Ajay,
Can you check if vlans are there in the config? and assigned to Po?
can you check output of show port-channel <> on both?
-
Siva
09-06-2012 05:14 AM
Yes port channel config on switches is fine .Vlans are there and allowed on Po.
interface Port-channel45
description ACE1
switchport
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 3001,3060,3200,3201,3208,3260-3262,3264,3265
switchport trunk allowed vlan add 3270-3272,3274,3275,3280,3300-3302,3650-3652
switchport trunk allowed vlan add 3661-3663,3668,3669,4090
switchport mode trunk
end
interface Port-channel46
description ACE2
switchport
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 3001,3060,3200,3201,3208,3260-3262,3264,3265
switchport trunk allowed vlan add 3270-3272,3274,3275,3280,3300-3302,3650-3652
switchport trunk allowed vlan add 3661-3663,3668,3669,4090
switchport mode trunk
09-06-2012 08:19 PM
Hi Ajay,
Are these vlans showing up on both the ACE?
Can you send(PM) me the configs of both ACE and switch?
Regards,
Siva
09-28-2012 10:11 AM
Shut/no shut to port channel resolve this issue.
09-29-2012 02:21 AM
Thats Great. Thanks for letting me know Ajay.
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: