Cisco Bug Discussions

With router image XPedite5205-IOS-1-15.9.3.M1.bin, the CPU Hog failure could be induced with the command 'test cpurmi hog simple 1'But after upgrading the image to c5930-adventerprisek9-mz.SPA.159-3.M6a.bin, is there a new way to induce CPU Hog failu...

Hi !I have an issue on CISCO7609-S Version 12.2(33)SRC1.Given this simple config :int Te9/2.4000encaps dot1q 4000xconnect 10.10.10.10 10104000 encaps mplsbackup peer 10.10.10.11 10114000backup delay 10 30mtu 9100When UP with primary peer, MTU is 9100...

Why some features are only available in GRT (route-server, additional-paths) and not in VRF adress-family ?OK when the features are relative to MPLS labels distribution, but NOK for IP-only features, this breaks router virtualization.  

We had a trunked uplink port G1/1/2 admin shut. After reloading we got this error message. Running Cisco C9200L-48P-4G running 17.3.3. This was in a stack of 4 9200s. Had to disconnect all cables and stack cables, switch booted up like normal. So 17....

The workaround doesn't seem to be viable as the impact of this issue is felt already and it's not possible for us to know the domain of the captive portal to be added to theUmbrella Proxy Exclusion list in advance.We typically receive reports of conn...

We are seeing the same behavior on Cisco 6.0(2)U3(7) / cisco Nexus 3064.Could you please confirm that it is a known bug for this version as well.

Has anyone found a better work around than switching to an IPSEC solution? The type of setup I have requires BGP and I can't lose that functionality. These sites need internet access and the only way to include traffic sourced from the VTI and out to...

Is there any chance that this enhancement will be considered in a future release? We are replacing Cisco IP Communicator by Jabber for Windows and the users are missing the callback feature. Jabber will not be deployed for all users so we cannot coun...

I am getting below error for custom reports that takes more than 3 minutes to return result.Report execution failed due to time out after 180 seconds. Please try again or increase the timeout using CLI.I looked around to check which CUIC parameter to...

Hi Community, I have many ISR4431 hitting this Bug CSCwf53555. At first they was running with 16.6.4, the we upgraded to 17.9.3a and then hit the bug (PID: ISR4XXX-PWR-UNKNOWN, VID: , SN:) Then we try with this: - Rollback to 16.6.4: here the output ...

rommon 56 > tftpdnldADDRESS: 192.168.10.5NETMASK: 255.255.255.0GATEWAY: 192.168.10.12SERVER: 192.168.10.12IMAGE: cisco-asa-fp3k.9.18.3.55.SPAVERBOSITY: ProgressRETRY: 40PKTTIMEOUT: 7200BLKSIZE: 1460CHECKSUM: YesPORT: GbE/1PHYMODE: Auto Detect.=======...

Have we noticed this issue regularly ?

I'm hitting what appears to be this bug, bug says terminated which I think means it won't be fixed? Anybody else use interface-templates on 17.6.4 successfully?

Hello, tested 17.9.3 on a 9800-L-F with 9130 APs. It is happening only on 5GHz; if I force the printers on 2.4GHz they have no issue connecting, but this is not a solution, any idea on when this will be solved?

set HTTP server keyring to defaultNo FTD CLI is available, need to use backdoor to enable FxOS CLI (sysopt sam 1001 on)/security* # commit-bufferError: Changes not allowed. use: 'connect ftd' to make changes.