11-15-2012 12:20 AM - edited 03-12-2019 09:55 AM
This document describes how to resolve this issue of getting the following alert:
LogPartitionLowWaterMarkExceeded UsedDiskSpace : 90 MessageString : Common Disk utilization hits
LWM! AppID : Cisco Log Partition Monitoring Tool ClusterID : NodeID : ENPUSFPKINF10
Following is the output of "show status" command from the CLI.
# show status
Host Name : <Hostname>
Date : Sat Jan 21, 2012 05:28:35
Time Zone : Eastern Standard Time (America/New_York)
Locale : en_US.UTF-8
Product Ver : 7.1.3.32900-4
Platform Ver : 2.0.0.1-1
License MAC : <mac>
Uptime:
05:28:36 up 4 days, 2:18, 1 user, load average: 0.58, 0.54, 0.53
CPU Idle: 98.03% System: 00.99% User: 00.99%
IOWAIT: 00.00% IRQ: 00.00% Soft: 00.00% Intr/sec: 1427.72
Memory Total: 2074832K
Free: 26000K
Used: 2048832K
Cached: 561472K
Shared: 0K
Buffers: 5344K
Total Free Used
Disk/active 12357724K 932912K 11299268K (93%)
Disk/inactive 12357692K 905184K 11326964K (93%)
Disk/logging 43009872K 4489328K 36335708K (90%)
Here you have three partitions in the Hard Disk, one is active partition, one is inactive partition, the third one is common partition which is for log/trace store. This error message indicates that you are having the log stored in common partition To resolve this issue you need to delete the unnecessary log files: For that
Also, disabling the traces which are not required and lowering the debug level for the enabled traces would also help.
Hi
I am getting the above error and tried the solution mentioned, but still get the alert and the disk usage is still high(94%). Can you advise?
Thank you for your help
Hi Ali,
I am running across the same issue and ran into this during my research.
https://supportforums.cisco.com/discussion/12136322/logpartitionlowwatermarkexceeded-rtmt-alert
Hopefully it will help you!
Diana
Hi Diana
Thanks for your reply I was on leave and just came back. I opened the link you posted and didn't know if I have to increase the number of the maximum number of files or to minimize it?
Thanks again
Ali
Hi Ali,
I would verify those numbers aren't higher then the default settings. In my case, I was coming across the same error / issue - LogPartitionLowWaterMarkExceeded UsedDiskSpace : 90.
It turned out the Maximum No. of Files was set alot higher then the default #, therefore the Disk Usage alert was triggered constantly. Lowering both the High/Low WaterMark exceeded threshold helped but only temporarily.
It wasn't until I adjusted the number of trace files that are kept to avoid hitting the low water mark again.
Hope this helps!
Diana
Hi Diana,
I have performed above mentioned steps but it only reduced 6% of disk space.
The current status is as below.
Total Free Used
Disk/active 14410560K 2571588K 11690208K (82%)
Disk/inactive 14643056K 2917552K 11576740K (80%)
Disk/logging 50989088K 6799208K 41599704K (86%)
Regards,
Farrukh
Good morning, I have the same error, but my Call Manager version is 11.5; this procedure also works for this release, because after "Check Cisco CTIManager and Cisco CallManager", another screen appears asking me to select the PLM Services / Applications, I select Cisco Prime LM DB, and Cisco Prime LM Server, ALL SERVERS, then of that I give NEXT, another screen appears where it asks me that I must select System Services / applications, in this point that I must do .. ??? I should select all the services the system shows me. ???
Please, expect your news.
Regards
Fernando,
Hi,
Any option to auto login to RTMT with pre-defined hostname and credentials.
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: