06-03-2023 05:19 AM
hi, I am trying to establish ESI between Swicth5 and leaf swicthes, NXOS2 and NXOS3, but for some reason, it fails on swicth 5. It comes up for a minute and then goes down citing "channel-misconfig (STP) error detected on Po10".
Code on NXOS: nxos.9.3.10.bin
Code on vIOS: vios_l2-adventerprisek9-m
Note: I have attached show run as an attachment. Shared below is the design.
NXOS2
----------
interface port-channel10
switchport mode trunk
switchport trunk allowed vlan 100,200
ethernet-segment 1234
system-mac 0000.0000.2011
interface Ethernet1/3
switchport mode trunk
switchport trunk allowed vlan 100,200
channel-group 10 mode active
Spanning tree config
--------------------
spanning-tree mode mst
spanning-tree domain enable
spanning-tree mst 0-1 priority 8192
spanning-tree mst configuration
name VXLAN-FABRIC
instance 1 vlan 100,200
LEAF-101(config)# show spanning-tree summary
Switch is in mst mode (IEEE Standard)
L2 Gateway Domain ID: 1
Port Type Default is disable
Edge Port [PortFast] BPDU Guard Default is disabled
Edge Port [PortFast] BPDU Filter Default is disabled
Bridge Assurance is enabled
Loopguard Default is disabled
Pathcost method used is long
PVST Simulation is enabled
STP-Lite is disabled
NXOS3
---------------------------------------
interface port-channel10
switchport mode trunk
switchport trunk allowed vlan 100,200
ethernet-segment 1234
system-mac 0000.0000.2011
interface Ethernet1/3
switchport mode trunk
switchport trunk allowed vlan 100,200
channel-group 10 mode active
Spanning tree config
--------------------
spanning-tree mode mst
panning-tree domain enable
spanning-tree mst 0-1 priority 8192
spanning-tree mst configuration
name VXLAN-FABRIC
instance 1 vlan 100,200
LEAF-102# show spanning-tree summary
Switch is in mst mode (IEEE Standard)
L2 Gateway Domain ID: 1
Port Type Default is disable
Edge Port [PortFast] BPDU Guard Default is disabled
Edge Port [PortFast] BPDU Filter Default is disabled
Bridge Assurance is enabled
Loopguard Default is disabled
Pathcost method used is long
PVST Simulation is enabled
STP-Lite is disabled
Swicth5
----------
*Jun 3 11:46:54.085: %PM-4-ERR_DISABLE: channel-misconfig (STP) error detected on Po10, putting Gi0/0 in err-disable state
*Jun 3 11:46:54.088: %PM-4-ERR_DISABLE: channel-misconfig (STP) error detected on Po10, putting Gi0/1 in err-disable state
*Jun 3 11:46:54.091: %PM-4-ERR_DISABLE: channel-misconfig (STP) error detected on Po10, putting Po10 in err-disable state
*Jun 3 11:46:55.086: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state to down
*Jun 3 11:46:55.088: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/1, changed state to down
*Jun 3 11:46:56.088: %LINK-3-UPDOWN: Interface GigabitEthernet0/0, changed state to down
*Jun 3 11:46:56.090: %LINK-3-UPDOWN: Interface Port-channel10, changed state to down
*Jun 3 11:46:56.091: %LINK-3-UPDOWN: Interface GigabitEthernet0/1, changed state to down
*Jun 3 11:46:57.090: %LINEPROTO-5-UPDOWN: Line protocol on Interface Port-channel10, changed state to down
show interface status , when po 10 was up
------------------------------------------
Port Name Status Vlan Duplex Speed Type
Gi0/0 connected trunk a-full auto RJ45
Gi0/1 connected trunk a-full auto RJ45
Spanning tree configuration
----------------------------
spanning-tree mode mst
spanning-tree mst configuration
name VXLAN-FABRIC
instance 1 vlan 100, 200
spanning-tree mst 0-1 priority 61440
FEX-1#show run int gig 0/0
Building configuration...
Current configuration : 145 bytes
!
interface GigabitEthernet0/0
switchport trunk encapsulation dot1q
switchport mode trunk
negotiation auto
channel-group 10 mode active
end
Interface configuration
--------------------------------------
FEX-1#show run int gig 0/1
Building configuration...
Current configuration : 145 bytes
!
interface GigabitEthernet0/1
switchport trunk encapsulation dot1q
switchport mode trunk
negotiation auto
channel-group 10 mode active
end
FEX-1#show run int po 10
Building configuration...
Current configuration : 93 bytes
!
interface Port-channel10
switchport trunk encapsulation dot1q
switchport mode trunk
end
06-03-2023 05:21 AM
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide