hello i am trying to configure my cisco 829 with this simple code snipped but the device refuse to ping 8.8.8.8 or 0.0.0.0 etc and the cellular 0/0 or 1/0 refuse to get ip address, i use a generic sim card and i dont know if the problem is related to that but the sim cards seems to be active and working, my current config is
Current configuration : 3777 bytes
!
! Last configuration change at 19:32:26 UTC Tue Apr 30 2024
!
version 15.7
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname IR800
!
boot-start-marker
boot-end-marker
!
!
!
no aaa new-model
service-module wlan-ap 0 bootimage autonomous
!
ignition off-timer 900
!
ignition undervoltage threshold 11
!
no ignition enable
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
ip cef
no ipv6 cef
!
multilink bundle-name authenticated
!
!
!
chat-script lte "" "AT!CALL" TIMEOUT 20 "OK"
!
!
license udi pid IR829-2LTE-EA-BK9 sn FTX2223Z023
!
!
vtp mode transparent
!
redundancy
!
!
!
!
!
controller Cellular 0
lte sim data-profile 3 attach-profile 3
lte modem link-recovery rssi onset-threshold -110
lte modem link-recovery monitor-timer 20
lte modem link-recovery wait-timer 10
lte modem link-recovery debounce-count 6
!
controller Cellular 1
no lte gps enable
lte modem link-recovery rssi onset-threshold -110
lte modem link-recovery monitor-timer 20
lte modem link-recovery wait-timer 10
lte modem link-recovery debounce-count 6
!
vlan 11
name 10.202.241.0/24_DATA
!
!
!
!
!
!
!
!
!
!
!
interface GigabitEthernet0
no ip address
shutdown
!
interface GigabitEthernet1
no ip address
!
interface GigabitEthernet2
no ip address
!
interface GigabitEthernet3
no ip address
!
interface GigabitEthernet4
no ip address
!
interface Wlan-GigabitEthernet0
no ip address
!
interface GigabitEthernet5
no ip address
shutdown
duplex auto
speed auto
!
interface Cellular0/0
ip address negotiated
ip virtual-reassembly in
encapsulation slip
dialer in-band
dialer idle-timeout 0
dialer enable-timeout 6
dialer string lte
dialer-group 1
no peer default ip address
ipv6 address dhcp
async mode interactive
routing dynamic
!
interface Cellular1/0
ip address negotiated
ip virtual-reassembly in
encapsulation slip
shutdown
dialer in-band
dialer idle-timeout 0
dialer string lte
dialer-group 1
ipv6 address autoconfig
!
interface Cellular0/1
no ip address
encapsulation slip
!
interface Cellular1/1
no ip address
encapsulation slip
!
interface wlan-ap0
no ip address
shutdown
!
interface Vlan1
no ip address
!
interface Async0
no ip address
encapsulation scada
!
interface Async1
no ip address
encapsulation scada
!
interface Dialer1
no ip address
!
!
ip forward-protocol nd
!
no ip http server
no ip http secure-server
!
ip nat inside source list NAT interface Cellular0/0 overload
ip route 0.0.0.0 0.0.0.0 Cellular1/0
!
ip access-list extended NAT
permit ip 10.0.0.0 0.0.0.255 any
!
dialer-list 1 protocol ip permit
ipv6 ioam timestamp
!
!
access-list 1 permit any
!
control-plane
!
!
!
vstack
!
line con 0
stopbits 1
line 1 2
stopbits 1
line 3
script dialer lte
no exec
transport preferred lat pad telnet rlogin lapb-ta mop udptn v120 ssh
transport output lat pad telnet rlogin lapb-ta mop udptn v120 ssh
line 4
no activation-character
no exec
transport preferred none
transport input all
transport output lat pad telnet rlogin lapb-ta mop udptn v120 ssh
line 8
no exec
transport preferred lat pad telnet rlogin lapb-ta mop udptn v120 ssh
transport output lat pad telnet rlogin lapb-ta mop udptn v120 ssh
line 9
script dialer lte
no exec
transport preferred lat pad telnet rlogin lapb-ta mop udptn v120 ssh
transport output lat pad telnet rlogin lapb-ta mop udptn v120 ssh
line 15
no exec
transport preferred lat pad telnet rlogin lapb-ta mop udptn v120 ssh
transport output lat pad telnet rlogin lapb-ta mop udptn v120 ssh
line 1/3 1/6
transport preferred none
transport output none
stopbits 1
line vty 0 4
login
transport input none
!
no scheduler max-task-time
no iox hdm-enable
iox client enable interface GigabitEthernet5
no iox recovery-enable
!
!
!
!
