I am trying to figure out a way to Integrate our vulnerability assessment tool (Rapid7 InsightVM) and our ticketing system (Ivanti Service Manager) to automate ticket creations. My idea was to utilize SecureX Serverless Relays and use SecureX Orchest...
Forum Posts
Hi, I´m wondering if Meraki MX integrates with SecureX like a ASA or FTD. If yes, then how is the integration done? I only find the SSO integration, that´s visibility and that´s not what I´m looking for. Thanks!Threat Insights, Cisco SecureXAndreas
Does anyone know what the maximum supported contexts is on the FPR1140? This article mentions: 10CLI Book 1: Cisco ASA Series General Operations CLI Configuration Guide, 9.13 - Licenses: Smart Software Licensing (ASAv, ASA on Firepower) [Cisco Adapti...
Hello I hope your are all well I wanted to know the possibility to configure an ASA NGFW cluster in transparent mode in the following context. I started to work with the EVE-NG tool but I had problems activating the FTD interfaces, I can't put the...
Hello All I hope you're okay. I applied an erase configuration from the local-mgmt interface and now I can't access the FTD, the system shows me that the Ftd has not installed. I tried to follow the cisco links but it doesn't work Also I tried to use...
I am trying to set up Call manager CDR records to go to our new cloud call accounting server and keep getting blocked by the firewall and hope you can direct us to the right place to fix this. I see this in Events: And I created this policy rule b...
I have a ISE environment witch is integrated with AD. I inherited this from 2 past engineers. This being said there are many sites that are attached and use different AD groups to add and remove permisions to different types of network appliances. Is...
Hi Guys, On ISE, when you navigate to Context Visibility -> Endpoints, the page will show you the MAC addresses of the device. Can we know when is the device registered and how it is registered? So I have this WiFi SSID that if you want to connect to...
Hi All,I am replacing an existing ASA 5525 device with new ASA 5525 FTD. All configuration need to migrate into new box. After successfully perform the migration (Using Firepower Migration Tool (FMT) and a temporary Virtual Firepower Management Cente...
Resolved! Creating a posture policy using Axonius
I am trying to find a good document or video resource to explain how to integrate with my asset inventory system. Our initial idea for posture will be to validate VPN user authentication and the device being listed in this 3rd party platform.
Hello and good day, I try to play the software ise-1.1.1.268.i386 on the Cisco ISE-3355. After detecting the hard drive, I get the following message: Detected Cisco UDI (Unique Device Identifier):PID: ISE-3355-K9 , VID: V02, SN: KQ1F2BMError: Unable ...
In Firepower connection events, I see there are numerous connections that do not have any user. If I go to connection events and search the IP the user has, the user field shows no data. If I go to active sessions and search the same IP address, it s...
Hello;We are running a Firepower 2110 and it works fine so far.We have an official IP Address with NAT to one of our private Exchange CAS Server.I want that only the Port 80,443,587 are accessible from the Internet, what is the best way to restrict t...
Resolved! Renew SecureX Admin Access with Duo MFA
I had working admn access to SecureX admin portal with MFA by Duo. But I had to change my phone and now I am not able to access the site as for any change I need to use Duo Push or Enter a Passcode - and without it I am not able to do anything. Shoul...
Hi, I have a distributed ISE deployment with 2 PAN (PxGrid enabled) nodes, 2 MNT and 5 PSNs. I have integrated Check Point Identity Collector with ISE PxGrid Node. While integrating I exported Internal CA certificate from 'Primary PxGrid Node' which ...