05-09-2008 03:26 AM - edited 03-15-2019 10:33 AM
Dear All,
Two Cisco routers are connected as follows:
VoIP--> R1 -->ISDN--> R2 -->VoIP
Appreciate any ideas or recommendations to get successful calls from R1 to R2?
The Problem: When the call leaves R1 to R2 over the ISDN link in between i see the call coming on R2 and then disconnected with the following disconnect reason:
Cause i = 0x82E6 - Recovery on timer expiry
R1 config:
---------------
!
interface Serial4/0:15
no ip address
encapsulation hdlc
no logging event link-status
isdn switch-type primary-net5
isdn overlap-receiving T302 5000
isdn protocol-emulate network
isdn incoming-voice voice
no cdp enable
!
dial-peer voice 10 pots
preference 1
destination-pattern 000T
progress_ind alert enable 8
direct-inward-dial
port 4/0:15
!
dial-peer voice 11 pots
preference 3
destination-pattern .T
progress_ind alert enable 8
direct-inward-dial
port 4/0:15
forward-digits 5
!
R2 config:
--------------
!
interface Serial2/0:15
no ip address
encapsulation hdlc
no logging event link-status
isdn switch-type primary-net5
isdn overlap-receiving T302 4000
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
no cdp enable
!
dial-peer voice 99 pots
tone ringback alert-no-PI
preference 2
destination-pattern .T
progress_ind setup enable 3
progress_ind alert enable 8
progress_ind progress enable 1
progress_ind connect enable 1
incoming called-number .T
no digit-strip
direct-inward-dial
port 2/0:15
!
dial-peer voice 100 voip
destination-pattern 89...
progress_ind setup enable 3
progress_ind progress enable 1
progress_ind connect enable 1
voice-class codec 1
session target ipv4:10.1.1.2
incoming called-number .T
no vad
!
Debug isdn q931 from R2
------------------------------------
*May 7 13:39:25.129: ISDN Se2/0:15 Q931: RX <- SETUP pd = 8 callref = 0x014D
Bearer Capability i = 0x8090A3
Standard = CCITT
Transfer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA98381
Exclusive, Channel 1
Net Specific Fac i = 0x00E2
Calling Party Number i = 0x2181, '4364574474'
Plan:ISDN, Type:National
Called Party Number i = 0xA1, '89222'
Plan:ISDN, Type:National
*May 7 13:39:25.133: ISDN Se2/0:15 Q931: TX -> SETUP_ACK pd = 8 callref = 0x814D
Channel ID i = 0xA98381
Exclusive, Channel 1
*May 7 13:39:34.841: ISDN Se2/0:15 Q931: RX <- DISCONNECT pd = 8 callref = 0x014D
Cause i = 0x82E6 - Recovery on timer expiry
*May 7 13:39:34.845: ISDN Se2/0:15 Q931: TX -> RELEASE pd = 8 callref = 0x814D
*May 7 13:39:34.853: ISDN Se2/0:15 Q931: RX <- RELEASE_COMP pd = 8 callref = 0x014D
--------------------------
Any ideas or recommendations to get successful calls from R1 to R2?
Thanks in advance.
05-09-2008 03:52 AM
Hi, you've asked this already in another thread where I replied. Please do not open duplicate posts.
05-09-2008 04:59 AM
i wasn't sure under which forum to post, sorry for duplication...
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: