Cas 0 - collect-call-enable command, ios15

Juan Gerardo Hernandez · ‎01-03-2013

Hi, all,

I've havving problems with mi E1 R2_Digital voice port, the problem is that the calls cannot go in, but calls from IP Phones to PSTN can go out,

I wrote some debugs commands, with this error on the VMP command.

Jan 3 17:46:26.643: R2 Incoming Voice(0/0): DSX (E1 0/0/0:0): STATE: R2_IN_CALLERID R2 Got Event R2_TONE_OFF

Jan 3 17:46:26.643: r2_reg_generate_digits(0/0/0:0(1)): Tx digit '#'

Jan 3 17:46:26.743: htsp_digit_ready_up(0/0/0:0(1)): Rx digit='5'

Jan 3 17:46:26.743: R2 Incoming Voice(0/0): DSX (E1 0/0/0:0): STATE: R2_IN_CALLERID R2 Got Event 5

Jan 3 17:46:26.743: r2_reg_generate_digits(0/0/0:0(1)): Tx digit '1'

Jan 3 17:46:26.835: htsp_digit_ready(0/0/0:0(1)): Rx digit='#'

Jan 3 17:46:26.835: R2 Incoming Voice(0/0): DSX (E1 0/0/0:0): STATE: R2_IN_CALLERID R2 Got Event R2_TONE_OFF

Jan 3 17:46:26.835: r2_reg_generate_digits(0/0/0:0(1)): Tx digit '#'

Jan 3 17:46:26.923: htsp_digit_ready_up(0/0/0:0(1)): Rx digit='1'

Jan 3 17:46:26.923: R2 Incoming Voice(0/0): DSX (E1 0/0/0:0): STATE: R2_IN_CALLERID R2 Got Event 1

Jan 3 17:46:26.923: r2_reg_generate_digits(0/0/0:0(1)): Tx digit '1'

Jan 3 17:46:27.015: htsp_digit_ready(0/0/0:0(1)): Rx digit='#'

Jan 3 17:46:27.015: R2 Incoming Voice(0/0): DSX (E1 0/0/0:0): STATE: R2_IN_CALLERID R2 Got Event R2_TONE_OFF

Jan 3 17:46:27.015: r2_reg_generate_digits(0/0/0:0(1)): Tx digit '#'

Jan 3 17:46:27.103: htsp_digit_ready_up(0/0/0:0(1)): Rx digit='3'

Jan 3 17:46:27.103: R2 Incoming Voice(0/0): DSX (E1 0/0/0:0): STATE: R2_IN_CALLERID R2 Got Event 3

Jan 3 17:46:27.103: r2_reg_generate_digits(0/0/0:0(1)): Tx digit '1'

Jan 3 17:46:27.195: htsp_digit_ready(0/0/0:0(1)): Rx digit='#'

Jan 3 17:46:27.195: R2 Incoming Voice(0/0): DSX (E1 0/0/0:0): STATE: R2_IN_CALLERID R2 Got Event R2_TONE_OFF

Jan 3 17:46:27.195: r2_reg_generate_digits(0/0/0:0(1)): Tx digit '#'

Jan 3 17:46:27.283: htsp_digit_ready_up(0/0/0:0(1)): Rx digit='0'

Jan 3 17:46:27.283: R2 Incoming Voice(0/0): DSX (E1 0/0/0:0): STATE: R2_IN_CALLERID R2 Got Event 10

Jan 3 17:46:27.283: r2_reg_generate_digits(0/0/0:0(1)): Tx digit '1'

Jan 3 17:46:27.375: htsp_digit_ready(0/0/0:0(1)): Rx digit='#'

Jan 3 17:46:27.375: R2 Incoming Voice(0/0): DSX (E1 0/0/0:0): STATE: R2_IN_CALLERID R2 Got Event R2_TONE_OFF

Jan 3 17:46:27.375: r2_reg_generate_digits(0/0/0:0(1)): Tx digit '#'

Jan 3 17:46:27.463: htsp_digit_ready_up(0/0/0:0(1)): Rx digit='0'

Jan 3 17:46:27.463: R2 Incoming Voice(0/0): DSX (E1 0/0/0:0): STATE: R2_IN_CALLERID R2 Got Event 10

Jan 3 17:46:27.463: r2_reg_generate_digits(0/0/0:0(1)): Tx digit '1'

Jan 3 17:46:27.555: htsp_digit_ready(0/0/0:0(1)): Rx digit='#'

Jan 3 17:46:27.555: R2 Incoming Voice(0/0): DSX (E1 0/0/0:0): STATE: R2_IN_CALLERID R2 Got Event R2_TONE_OFF

Jan 3 17:46:27.555: r2_reg_generate_digits(0/0/0:0(1)): Tx digit '#'

Jan 3 17:46:27.643: htsp_digit_ready_up(0/0/0:0(1)): Rx digit='0'

Jan 3 17:46:27.643: R2 Incoming Voice(0/0): DSX (E1 0/0/0:0): STATE: R2_IN_CALLERID R2 Got Event 10

Jan 3 17:46:27.643: r2_reg_generate_digits(0/0/0:0(1)): Tx digit '5'

Jan 3 17:46:27.735: htsp_digit_ready(0/0/0:0(1)): Rx digit='#'

Jan 3 17:46:27.735: R2 Incoming Voice(0/0): DSX (E1 0/0/0:0): STATE: R2_IN_COLLECT_DNIS R2 Got Event R2_TONE_OFF

Jan 3 17:46:27.735: r2_reg_generate_digits(0/0/0:0(1)): Tx digit '#'

Jan 3 17:46:27.859: htsp_process_event: [0/0/0:0(1), R2_Q421_IC_WAIT_ANSWER, E_DSP_SIG_1000]

Jan 3 17:46:27.859: r2_q421_ic_clr_fwd_idle(0/0/0:0(1)) Rx CLEAR FWD

Jan 3 17:46:27.859: r2_reg_channel_disconnected(0/0/0:0(1))

Jan 3 17:46:27.859: R2 Incoming Voice(0/0): DSX (E1 0/0/0:0): STATE: R2_IN_COLLECT_DNIS R2 Got Event R2_STOP

Jan 3 17:46:27.859: r2_reg_generate_digits(0/0/0:0(1)): Tx digit '#'

Jan 3 17:46:27.859: htsp_timer - 2000 msec

Jan 3 17:46:27.859: htsp_process_event: [0/0/0:0(1), R2_Q421_IC_CLR_FWD, E_HTSP_RELEASE_REQ]

Jan 3 17:46:27.859: r2_q421_null_release(0/0/0:0(1)) E_HTSP_RELEASE_REQ

Jan 3 17:46:27.859: r2_reg_process_event: [0/0/0:0(1), R2_REG_COLLECTING, E_R2_REG_DISCONNECT(91)]

Jan 3 17:46:27.859: r2_reg_disconnect_collect(0/0/0:0(1))

Jan 3 17:46:27.859: r2_reg_timer_stop(0/0/0:0(1))

Jan 3 17:46:29.859: htsp_process_event: [0/0/0:0(1), R2_Q421_IC_CLR_FWD, E_HTSP_EVENT_TIMER]

Jan 3 17:46:29.859: htsp_timer_stop

Jan 3 17:46:29.859: r2_q421_clr_fwd_idle(0/0/0:0(1)) Tx IDLEvnm_dsp_set_sig_state:[R2 Q.421 0/0/0:0(1)] set signal state = 0x8

Jan 3 17:46:29.859: r2_reg_channel_disconnected(0/0/0:0(1))

Jan 3 17:46:29.859: r2_reg_process_event: [0/0/0:0(1), R2_REG_IDLE, E_R2_REG_DISCONNECT(91)]

Jan 3 17:46:29.859: r2_reg_disconnect_idle(0/0/0:0(1))

Jan 3 17:46:29.859: R2 Incoming Voice(0/0): DSX (E1 0/0/0:0): STATE: R2_IN_IDLE R2 Got Event R2_STOP

This is mi conf from the controller e1:

controller E1 0/0/0

framing NO-CRC4

line-termination 75-ohm

ds0-group 0 timeslots 1-15,17-31 type r2-digital r2-compelled ani

cas-custom 0

invert-abcd 0 0 1 1

country telmex

category 2

answer-signal group-b 1

ani-digits min 0 max 10

I've searching for thi error and in some post from cisco, the aswer to solve this was implement this command:

(config)#controller e1 0/0/0
 (config-controller)#cas-custom 0
 (config-ctrl-cas)#collect-call-enable

But it is not under the CAS custom 0.

vpn(config-controller)#cas-custom 0

gwpitvpn(config-ctrl-cas)#co?

country

vpn(config-ctrl-cas)#collect-call-enable

^

% Invalid input detected at '^' marker.

vpn(config-ctrl-cas)#

show you please help me with my problem?

Mi IOS version is:

flash0:c3900e-universalk9-mz.SPA.151-4.M4.bin

reggards

P.D. This is the link with the answer of the "collect-call-enable" command.

https://supportforums.cisco.com/thread/2127105

jorgmar2 · ‎01-03-2013

Hello Gerardo,

can you please try the next configuration?

!

controller E1 1/0

framing NO-CRC4

ds0-group 0 timeslots 1-3 type r2-digital r2-semi-compelled ani

cas-custom 0

country telmex

category 2

answer-signal group-b 1

dnis-digits min 3 max 13

ani-digits min 1 max 10

groupa-callerid-end

!

voice-port 1/0:0

cptone MX

!

dial-peer voice 34 pots

destination-pattern .T

direct-inward-dial

port 1/0:0

Please let us know how it goes,

Juan Gerardo Hernandez · ‎01-03-2013

Hi jogmar,

I tried but it did't work,

Here is the configuration.

controller E1 0/0/0

framing NO-CRC4

line-termination 75-ohm

ds0-group 0 timeslots 1-15,17-31 type r2-digital r2-compelled ani

cas-custom 0

country telmex

category 2

answer-signal group-b 1

dnis-digits min 3 max 13

ani-digits min 1 max 10

groupa-callerid-end

description "Enlace E1 PSTN AXTEL"

voice-port 0/0/0:0

cptone MX

!

dial-peer voice 1000 pots

destination-pattern .T

incoming called-number .

direct-inward-dial

port 0/0/0:0

no register e164

PORT CODEC VAD VTSP STATE VPM STATE

============== ========= === ==================== ======================

0/0/0:0.1 - - - R2_Q421_IDLE

0/0/0:0.2 - - - R2_Q421_IDLE

0/0/0:0.3 - - - R2_Q421_IDLE

0/0/0:0.4 - - - R2_Q421_IDLE

0/0/0:0.5 - - - R2_Q421_IDLE

0/0/0:0.6 - - - R2_Q421_IDLE

0/0/0:0.7 - - - R2_Q421_IDLE

0/0/0:0.8 - - - R2_Q421_IDLE

0/0/0:0.9 - - - R2_Q421_IDLE

0/0/0:0.10 - - - R2_Q421_IDLE

0/0/0:0.11 - - - R2_Q421_IDLE

0/0/0:0.12 - - - R2_Q421_IDLE

0/0/0:0.13 - - - R2_Q421_IDLE

0/0/0:0.14 - - - R2_Q421_IDLE

0/0/0:0.15 - - - R2_Q421_IDLE

0/0/0:0.17 - - - R2_Q421_IDLE

0/0/0:0.18 - - - R2_Q421_IDLE

0/0/0:0.19 - - - R2_Q421_IDLE

0/0/0:0.20 - - - R2_Q421_IDLE

0/0/0:0.21 - - - R2_Q421_IDLE

0/0/0:0.22 - - - R2_Q421_IDLE

0/0/0:0.23 - - - R2_Q421_IDLE

0/0/0:0.24 - - - R2_Q421_IDLE

0/0/0:0.25 - - - R2_Q421_IDLE

0/0/0:0.26 - - - R2_Q421_IDLE

0/0/0:0.27 - - - R2_Q421_IDLE

0/0/0:0.28 - - - R2_Q421_IDLE

0/0/0:0.29 - - - R2_Q421_IDLE

0/0/0:0.30 - - - R2_Q421_IDLE

0/0/0:0.31 - - - R2_Q421_IDLE

dial-peer hunt 0

AD PRE PASS OUT

TAG TYPE MIN OPER PREFIX DEST-PATTERN FER THRU SESS-TARGET STAT PORT KEEPALIVE

3000 voip up up 81272.... 1 syst ipv4:10.2

3001 voip up up 81272.... 2 syst ipv4:10.2

1000 pots up up .T 0 up 0/0/0:0

E1 0/0/0 is up.

Applique type is Channelized E1 - unbalanced

Description: "Enlace E1 PSTN AXTEL"

No alarms detected.

alarm-trigger is not set

Version info FPGA Rev: 08121917, FPGA Type: PRK4

Framing is NO-CRC4, Line Code is HDB3, Clock Source is Line.

International Bit: 1, National Bits: 11111

Data in current interval (838 seconds elapsed):

0 Line Code Violations, 0 Path Code Violations

132 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins

132 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs

Total Data (last 24 hours)

0 Line Code Violations, 0 Path Code Violations,

13432 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,

13432 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs

I am still getting that error:

Jan  3 21:15:50.720: htsp_digit_ready(0/0/0:0(1)): Rx digit='#'
Jan  3 21:15:50.720: R2 Incoming Voice(0/0): DSX (E1 0/0/0:0): STATE: R2_IN_CALLERID R2 Got Event R2_TONE_OFF
Jan  3 21:15:50.720: r2_reg_generate_digits(0/0/0:0(1)): Tx digit '#'
Jan  3 21:15:50.820: htsp_digit_ready_up(0/0/0:0(1)): Rx digit='3'
Jan  3 21:15:50.820: R2 Incoming Voice(0/0): DSX (E1 0/0/0:0): STATE: R2_IN_CALLERID R2 Got Event 3
Jan  3 21:15:50.820: r2_reg_generate_digits(0/0/0:0(1)): Tx digit '1'
Jan  3 21:15:50.920: htsp_digit_ready(0/0/0:0(1)): Rx digit='#'
Jan  3 21:15:50.920: R2 Incoming Voice(0/0): DSX (E1 0/0/0:0): STATE: R2_IN_CALLERID R2 Got Event R2_TONE_OFF
Jan  3 21:15:50.920: r2_reg_generate_digits(0/0/0:0(1)): Tx digit '#'
Jan  3 21:15:51.020: htsp_digit_ready_up(0/0/0:0(1)): Rx digit='0'
Jan  3 21:15:51.020: R2 Incoming Voice(0/0): DSX (E1 0/0/0:0): STATE: R2_IN_CALLERID R2 Got Event 10
Jan  3 21:15:51.020: r2_reg_generate_digits(0/0/0:0(1)): Tx digit '1'
Jan  3 21:15:51.120: htsp_digit_ready(0/0/0:0(1)): Rx digit='#'
Jan  3 21:15:51.120: R2 Incoming Voice(0/0): DSX (E1 0/0/0:0): STATE: R2_IN_CALLERID R2 Got Event R2_TONE_OFF
Jan  3 21:15:51.120: r2_reg_generate_digits(0/0/0:0(1)): Tx digit '#'
Jan  3 21:15:51.220: htsp_digit_ready_up(0/0/0:0(1)): Rx digit='0'
Jan  3 21:15:51.220: R2 Incoming Voice(0/0): DSX (E1 0/0/0:0): STATE: R2_IN_CALLERID R2 Got Event 10
Jan  3 21:15:51.220: r2_reg_generate_digits(0/0/0:0(1)): Tx digit '1'
Jan  3 21:15:51.320: htsp_digit_ready(0/0/0:0(1)): Rx digit='#'
Jan  3 21:15:51.320: R2 Incoming Voice(0/0): DSX (E1 0/0/0:0): STATE: R2_IN_CALLERID R2 Got Event R2_TONE_OFF
Jan  3 21:15:51.320: r2_reg_generate_digits(0/0/0:0(1)): Tx digit '#'
Jan  3 21:15:51.420: htsp_digit_ready_up(0/0/0:0(1)): Rx digit='0'
Jan  3 21:15:51.420: R2 Incoming Voice(0/0): DSX (E1 0/0/0:0): STATE: R2_IN_CALLERID R2 Got Event 10
Jan  3 21:15:51.420: r2_reg_generate_digits(0/0/0:0(1)): Tx digit '5'
Jan  3 21:15:51.508: htsp_digit_ready(0/0/0:0(1)): Rx digit='#'
Jan  3 21:15:51.508: R2 Incoming Voice(0/0): DSX (E1 0/0/0:0): STATE: R2_IN_COLLECT_DNIS R2 Got Event R2_TONE_OFF
Jan  3 21:15:51.508: r2_reg_generate_digits(0/0/0:0(1)): Tx digit '#'
Jan  3 21:15:51.636: htsp_process_event: [0/0/0:0(1), R2_Q421_IC_WAIT_ANSWER, E_DSP_SIG_1000]
Jan  3 21:15:51.636: r2_q421_ic_clr_fwd_idle(0/0/0:0(1)) Rx CLEAR FWD
Jan  3 21:15:51.636: r2_reg_channel_disconnected(0/0/0:0(1))
Jan  3 21:15:51.636: R2 Incoming Voice(0/0): DSX (E1 0/0/0:0): STATE: R2_IN_COLLECT_DNIS R2 Got Event R2_STOP
Jan  3 21:15:51.636: r2_reg_generate_digits(0/0/0:0(1)): Tx digit '#'
Jan  3 21:15:51.636: htsp_timer - 2000 msec
Jan  3 21:15:51.636: htsp_process_event: [0/0/0:0(1), R2_Q421_IC_CLR_FWD, E_HTSP_RELEASE_REQ]
Jan  3 21:15:51.636: r2_q421_null_release(0/0/0:0(1)) E_HTSP_RELEASE_REQ
Jan  3 21:15:51.636: r2_reg_process_event: [0/0/0:0(1), R2_REG_COLLECTING, E_R2_REG_DISCONNECT(91)] 
Jan  3 21:15:51.636: r2_reg_disconnect_collect(0/0/0:0(1))
Jan  3 21:15:51.636: r2_reg_timer_stop(0/0/0:0(1))
Jan  3 21:15:53.636: htsp_process_event: [0/0/0:0(1), R2_Q421_IC_CLR_FWD, E_HTSP_EVENT_TIMER]
Jan  3 21:15:53.636: htsp_timer_stop 
Jan  3 21:15:53.636: r2_q421_clr_fwd_idle(0/0/0:0(1)) Tx IDLEvnm_dsp_set_sig_state:[R2 Q.421 0/0/0:0(1)] set signal state = 0x8
Jan  3 21:15:53.636: r2_reg_channel_disconnected(0/0/0:0(1))
Jan  3 21:15:53.636: r2_reg_process_event: [0/0/0:0(1), R2_REG_IDLE, E_R2_REG_DISCONNECT(91)] 
Jan  3 21:15:53.636: r2_reg_disconnect_idle(0/0/0:0(1))
Jan  3 21:15:53.636: R2 Incoming Voice(0/0): DSX (E1 0/0/0:0): STATE: R2_IN_IDLE R2 Got Event R2_STOP
Jan  3 21:15:53.636: r2_reg_timer_stop(0/0/0:0(1))

Regards

jmthewissen · ‎01-07-2013

Hello Gerardo, there is a bug in some versions of IOS that repeats the last two digits of the DNIS and inserts them at the beginning of the stream, resulting in no matches for the call.

Could you please confirm that you are using an IOS that is also working on another router with the same provider, and that sucecesfully passing calls through? If that is the case please post or email me the complete config and I'll dig deeper into it. Otherwise, please use a version that you have tested somewhere else.

regards.

Juan Gerardo Hernandez · ‎01-07-2013

Hi Marc, I have this IOS image:

c3845-spservicesk9-mz.151-4.M.bin

with this configuration

controller E1 0/0/1
 framing NO-CRC4 
 line-termination 75-ohm
 ds0-group 0 timeslots 1-15,17-31 type r2-digital r2-compelled ani
 cas-custom 0
  invert-abcd 0 0 1 1
  country telmex
  category 2
  answer-signal group-b 1
  ani-digits min 0 max 10
  groupa-callerid-end
 description "Enlace E1 PSTN AXTEL"
!

it works!

But now I have this image.

c3900e-universalk9-mz.SPA.151-4.M4.bin

with this configuration.

controller E1 0/0/0

framing NO-CRC4

line-termination 75-ohm

ds0-group 0 timeslots 1-15,17-31 type r2-digital r2-compelled ani

cas-custom 0

invert-abcd 0 0 1 1

country telmex

category 2

answer-signal group-b 1

dnis-digits min 3 max 13

ani-digits min 1 max 10

groupa-callerid-end

description "Enlace E1 PSTN AXTEL"

And dows not work.

I cannot test the image file against another that works because we only have a 3900 router, The others routers are 3800.

I will e-mail you the configuration of both.

Regards.

spazziani · ‎08-04-2014

Hi everyone,

Did you solve your problem? I`m having a similar problem. Follow the descriptive below:

Hello,

The client has 2 sites and there is a problem when Site A connects via PSTN to Site B. Site B The phone rings once and then the call is disconnected.

Site A Site B
Extension Extension
2573 001332138122
PBX ---- ROUTER--------PSTN-------------ROUTER---------------PABX

And when do I link from Site B to Site A call is connected normally.

Colotei the log router Site A (Debug vpm signal). Follows the Annex to Debug.

Juan Gerardo Hernandez · ‎04-09-2015

I problem was solved, I was an issue with the clocking source of the E1. Support changed the configuration, sadly I don't have the changes I will post it If I can find some configuration.

dsobrinho · ‎01-20-2015

Hi,

I do not know if the problem was resolved, so I seems that the inbound dial-peer is with plus config.

So, only remove the destination-pattern .T

dial-peer voice 1000 pots

destination-pattern .T

incoming called-number .

direct-inward-dial

port 0/0/0:0

no register e164

Best regards,

Daniel

Daniel Sobrinho

Marcos Eusebio · ‎03-19-2024

I had this issue, and due to the VPM debug also showed the message "R2_REG_IDLE, E_R2_REG_DISCONNECT(91)" solved it adding two commands under the voice-port interface (in my case):

voice-port 0/1/0:0
no vad <--- To disable the the voice activity detection
cptone MX <--- to set the tone frequency used in my country