cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
735
Views
0
Helpful
3
Replies
Beginner

CME 9.0 MOH options

I have 2 questions regarding Music On Hold options for CME 9.0

1) Can you use unicast or is multicast the only option on CME 9.0?

2) On a L3 3750 switch running IP BASE, is it possible to deliver MOH on the Voice VLAN (SVI) utilizing PIM STUB routing?

Here is my scenario:

ISDN2 (BRI)---2921--->(L3 routed)----->3750-----(VLAN211)------IP-Phones(6941)

MOH currently not working for internal calls when put on hold

2921 running CME 9.0 (15.2.2T)

- Telephony Services source is Loopback 0

- L3 routed link to the 3750 switch

3750 running IP BASE

- SVI (interface VLAN 211 defined for L3 voice vlan)

Below is are my Multicast Configs on the 2921 router and IP BASE 3750:

ROUTER:

!

ip multicast-routing

!

telephony-service

ip source-address 10.11.10.254 port 2000

moh "flash:music-on-hold.au"

multicast moh 239.0.0.1 port 2000 route 10.11.10.254 172.21.101.22

!

interface Loopback0

description ** Loopback **

ip address 10.11.10.254 255.255.255.255

!

interface GigabitEthernet0/0

description ** switch F1/0/1 **

bandwidth 100000

ip address 172.21.101.22 255.255.255.248

ip pim sparse-dense-mode

!

SWITCH:

!

ip multicast-routing distributed

!

interface FastEthernet1/0/1

description ** router G0/0 **

no switchport

bandwidth 100000

ip address 172.21.101.17 255.255.255.248

ip pim passive

speed 100

duplex full

!

interface Vlan211

description ** VOICE **

ip address 10.10.10.254 255.255.255.0

ip pim passive

!

Everyone's tags (4)
3 REPLIES 3
Hall of Fame Master

CME 9.0 MOH options

1. by default CME automatically select MoH to be multicast or unicast depending if phone is a subnet local to to CME router, or not ('remote phone').

2. as a consequence, the best choice is to have the phones be directly connected to CME router.

Highlighted
Beginner

CME 9.0 MOH options

Spent most of today trying L3 vs L2 vs L3 + dot1q for voice VLAN.. Same result - when internal calls are put On Hold - silence.. Finally tried a fresh set of phones with stock firmware. Everything worked straight away!

Basically, I just found a bug in 69xx CME 9.0 firmware ver 9.2.1 (SCCP). Phones on default load 9.0.2 work fine, even with a pure L3 switch on IP Base with multicast stub.

If anynoe is interested, here is my working CME multicast L3 3750 switch config on IP BASE:

!

ip routing

!

ip multicast-routing distributed

!

interface FastEthernet1/0/1

description ** router G0/0 **

no switchport

bandwidth 100000

ip address 172.21.101.17 255.255.255.248

ip pim sparse-dense-mode

speed 100

duplex full

!

interface Vlan211

description ** VOICE **

ip address 10.10.10.254 255.255.255.0

ip pim passive

!

Hall of Fame Master

CME 9.0 MOH options

The 69xx are known to have more bugs in recent firmware rather than in the original one.

Good that you found a solution anyway.

CreatePlease to create content
Content for Community-Ad
August's Community Spotlight Awards
This widget could not be displayed.