12-11-2013 04:43 AM - edited 03-16-2019 08:48 PM
Hello,
i'm trying to configure how to preserve hunt groups using the SRST-E using SRST manger ( no UMG).
Almost everything is working except hunt groups with parallel serving when one of the members in not connected.
Does somebody know how to solve it? when all ephones-dn from list are active it is working, if i shutdown the sip trunk to CUCM it is also working wit less member.
the SRST-E is hosted by the same router as the local gw so i need to have a trunk to CUCM, i'm using option-keepalive to brough down the sip trunk when simulating WAN outage.
I need to prefer the SIP trunk over local as in normal situation i need them to go CUCM. I see that the option-keep alive does not bring out down the dial-peer, only busy out. when i shutdown the dial-peer 11 it is also working with only 2 phones active instead of all 3. otherwise i get fast busy signal.
relevant config:
voice hunt-group 1 parallel
list 62,61,63
timeout 60
pilot 300
preference 4 secondary 9
dial-peer voice 11 voip
preference 1
destination-pattern 6[0-9]$
session protocol sipv2
session target ipv4:10.101.55.10
voice-class codec 1
voice-class sip options-keepalive up-interval 15 down-interval 5 retry 2
voice-class sip bind control source-interface Loopback0
voice-class sip bind media source-interface Loopback0
dtmf-relay rtp-nte
no vad
!
dial-peer voice 12 voip
preference 1
destination-pattern 300$
session protocol sipv2
session target ipv4:10.101.55.10
voice-class codec 1
voice-class sip options-keepalive up-interval 15 down-interval 5 retry 2
voice-class sip bind control source-interface Loopback0
voice-class sip bind media source-interface Loopback0
dtmf-relay rtp-nte
no vad
!
dial-peer hunt 2
ephone-dn 1 dual-line
number 61
pickup-group 1
description 61
name 61
preference 4
call-forward busy 200
call-forward noan 200 timeout 25
!
!
ephone-dn 2 dual-line
number 63
pickup-group 1
description 63
name 63
preference 4
!
!
ephone-dn 3 dual-line
number 62
pickup-group 1
description 62
preference 4
call-forward busy 200
call-forward noan 200 timeout 25
!
!
ephone 1
device-security-mode none
mac-address 34A8.4E60.CD9E
after-hours exempt
username "JursikD"
type 6941
button 1:1
!
!
!
ephone 2
device-security-mode none
mac-address 5C50.15A9.20E7
after-hours exempt
username "SEP5C5015A920E7"
type 7942
button 1:2
!
!
!
ephone 1000
device-security-mode none
mac-address FE51.B880.3876
type CIPC
button 1:3
dial-peer hunt 2
AD PRE PASS OUT
TAG TYPE MIN OPER PREFIX DEST-PATTERN FER THRU SESS-TARGET STAT PORT KEEPALIVE
1 pots up up .T 6 up 0/3/0
200 voip up up 2.. 0 syst ipv4:10.101.55.5
10 voip down down 6.. 0 syst ipv4:10.101.55.10
11 voip up up 6[0-9]$ 1 syst ipv4:10.101.55.10 busyout
12 voip up up 300$ 1 syst ipv4:10.101.55.10 busyout
20001 pots up up 61$ 4 50/0/1
20002 pots up up 63$ 4 50/0/2
20003 pots up up 62$ 4 50/0/3
40001 voip up up 64$ 4 syst ipv4:10.101.55.18:50
21474- voip up up 300$ 4 syst loopback:rtp
83647
thanks and Regards,
d.
12-11-2013 12:59 PM
Hello,
Some update. This happen if the the not registered phone is first in voice hunt group even if it should be parallel.
It not first it works as expected.
04-11-2014 04:14 AM
Hey,
have you ever found a solution for this problem?
I habe a similar problem. It occurs if the first number in the list is busy.
Kind regards
Andre
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide