Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
We use SolarWinds to monitor our network for the most part. On our monitor between a few routers we see very high jitter rates but with low latency. I'm fairly new to Cisco - so I am not really sure where to begin to look within the routers for what ...
Hi All,One of our customers requested us to propose an IPT solution. but among the specifications the below requirements are not clear for me please help on thatItemCurrent requirementFuture ExpansionAnalog Trunk Port32500E1 Interface215Integration ...
Hello All, I can Call from any Branch office to CUCM through Gatekeeper. But I cannot call from CUCM through Gatekeeper to any Branch.My CUCM version is 9.1.2 RegardsBahlul
I have a 2821 running IOS c2800nm-adventerprisek9-mz.151-4.M7 in a lab environment. I have it configured with SIP trunks to both CUCM and a termination provider. I am using static (source ip based) authentication with the provider. When I place calls...
Hi All We have users are remote based workers and they are on VPN.user1 - DN 3575 (remote VPN)user2 - DN 3574 (remote VPN)user3 - DN 3576 (HQ office) The issue is 2 remote users dial 4 digit DN to each, both party experience no-way audio once. But it...
Scenario:Setting up a new interactive voice system.The system uses two servers, each handles half of the total incoming calls.The IVS system connects to the call manager via a SIP trunk.The calls come in via a single 1-800 number, handled by the Call...
Hi All,We have a IPT cluster that we are trying to integrate to the AD. The local user IDs in CUCM with the EM profile mapped are 4 digit numeric IDs.I have a report of SAMAccount names from AD and I created a BAT file with the User ID ( as SAMAccoun...
Has anyone had any experience of setting up a SPA302D with CUCM?http://www.cisco.com/en/US/prod/collateral/voicesw/ps6788/phones/ps10998/ps12776/data_sheet_c78-717757.htmlAlthough the Datasheet doesn't specifically mention CUCM compatibility, I would...
This is the description of the issue, which occurs occassionaly:User was talking on one of their lines mid-sentence and all of a sudden they were talking to someone elseEach time the second caller they ended up with was a new caller; not someone on h...
I believe that I have had this problem in the past, but I can't remember what I did to fix it.I have a user that while playing a voice mail message, will get disconnected. As in, Unity just hangs up on them. It doesn't seem to be related to any par...
Hi, I have two sites - HUB with static WAN IP and Spoke with WAN IP from DHCP. Spoke site connects to Hub via ezvpn configuration. At Spoke site there is one ip phone in voice vlan that has VPN connectivity to HUB with CME. Phone registers corre...
hi there guys, we have a 2921 with a VIC2-4FXO out on a site in India the clients phones register over a managed MPLS network to a centralised CUCM clusterthe client wanted to break local calls out of analogue lines; the router is registered as an MG...
we recently got new Cisco 9971 devices at work but have some small annoyances. We usually have our phones configured with multiple lines (PA's picking up calls for their bosses). Firstly, a default line is selected by pressing the button to the left ...
Hi All,Strange issue that's just started happening with a few 6921 phones.On our cisco switch when port is configured with data and voice vlan, the phone picks up an IP address from the data vlan and in turn doesn't register. It's as if it doesn't se...
Here is my dilemma. I need to have a wireless speaker/mic in a conference room to allow me to use my Cisco 7942G phone for conferences (the phone will just sit on the side). I have tried various setups and nothing works. I have a Plantronics CS540...
