08-06-2014 02:41 AM - edited 03-16-2019 11:39 PM
Hello,
I configured a CME 2811 to establish conferences. When I want to add a phone on the conference I have : "cannot complete conference".
Here the harware inventory :
NAME: "2811 chassis", DESCR: "2811 chassis"
PID: CISCO2811 , VID: V02 , SN: FCZ100172DD
NAME: "2nd generation two port FXO voice interface daughtercard on Slot 0 SubSlot 0", DESCR: "2nd generation two port FXO voice interface daughtercard"
PID: VIC2-2FXO , VID: V01 , SN: FOC11277BNN
NAME: "3rd generation two port FXS DID voice interface daughtercard on Slot 0 SubSlot 1", DESCR: "3rd generation two port FXS DID voice interface daughtercard"
PID: VIC3-2FXS/DID , VID: V02 , SN: FOC13513229
NAME: "PVDMII DSP SIMM with one DSP with half channel capcity on Slot 0 SubSlot 4", DESCR: "PVDMII DSP SIMM with one DSP with half channel capcity"
PID: PVDM2-8 , VID: V01 , SN: FOC11415G48
I configured the cme :
voice-card 0
dspfarm
dsp services dspfarm
sccp local Loopback0
sccp ccm 10.192.255.158 identifier 77 priority 1 version 7.0
sccp
!
sccp ccm group 1
bind interface Loopback0
associate ccm 77 priority 1
associate profile 2 register conference
!
dspfarm profile 1 transcode
codec g711alaw
codec g711ulaw
codec g729r8
maximum sessions 1
associate application SCCP
!
dspfarm profile 2 conference
codec g711ulaw
codec g711alaw
conference-join custom-cptone jointone
conference-leave custom-cptone leavetone
associate application SCCP
shutdown
telephony-service
sdspfarm units 1
sdspfarm transcode sessions 128
sdspfarm tag 1 conference
conference hardware
I can't no shut the profile conference because maximu session is not defined. But the maximum is 0
CCME(config)#dspfarm profile 2 conference
CCME(config-dspfarm-profile)#maximum sessions ?
<0-0> Number of sessions assigned to this profile
Is the DSP allocated for other ressources ?
CCME-QAR#sh voice dsp
DSP DSP DSPWARE CURR BOOT PAK TX/RX
TYPE NUM CH CODEC VERSION STATE STATE RST AI VOICEPORT TS ABORT PACK COUNT
==== === == ======== ========== ===== ======= === == ========= == ===== ============
edsp 0001 01 g729r8 0.1 IDLE 50/0/1.1
edsp 0002 02 g711ulaw 0.1 IDLE 50/0/1.2
edsp 0003 01 g729r8 p 0.1 IDLE 50/0/4.1
edsp 0004 02 g729r8 p 0.1 IDLE 50/0/4.2
edsp 0005 01 g711ulaw 0.1 IDLE 50/0/5.1
edsp 0006 02 g711ulaw 0.1 IDLE 50/0/5.2
edsp 0007 01 g729r8 p 0.1 IDLE 50/0/6.1
edsp 0008 02 g729r8 p 0.1 IDLE 50/0/6.2
----------------------------FLEX VOICE CARD 0 ------------------------------
*DSP VOICE CHANNELS*
CURR STATE : (busy)inuse (b-out)busy out (bpend)busyout pending
LEGEND : (bad)bad (shut)shutdown (dpend)download pending
DSP DSP DSPWARE CURR BOOT PAK TX/RX
TYPE NUM CH CODEC VERSION STATE STATE RST AI VOICEPORT TS ABRT PACK COUNT
===== === == ========= ========== ===== ======= === == ========= == ==== ============
*DSP SIGNALING CHANNELS*
DSP DSP DSPWARE CURR BOOT PAK TX/RX
TYPE NUM CH CODEC VERSION STATE STATE RST AI VOICEPORT TS ABRT PACK COUNT
===== === == ========= ========== ===== ======= === == ========= == ==== ============
C5510 001 01 {flex} 24.3.4 alloc idle 0 0 0/0/0 02 0 38/0
C5510 001 02 {flex} 24.3.4 alloc idle 0 0 0/0/1 06 0 38/0
C5510 001 03 {flex} 24.3.4 alloc idle 0 0 0/1/0 02 0 221/0
C5510 001 04 {flex} 24.3.4 alloc idle 0 0 0/1/1 02 0 150/0
------------------------END OF FLEX VOICE CARD 0 ----------------------------
Thanks for your help
JB
Solved! Go to Solution.
08-06-2014 04:29 AM
Hi
yes , you have to increase your PVDM resources to get enough resources to do hardware conference . Your resources is used by Voice-cards 0/0 & 0/1.Can you disable transcode profie as the below:-
dspfarm profile 1 transcode
shu
no max sessions 1
dspfarm profile 2 conference
max sessions ?
Note: keep in your mind , no need for conference hardware if the conference will be between g711 participants "software Conference will be enough", if the conference will be done with other g729 Prticipant so in this time you will need conference hardware.
Thanks
please rate all useful information
08-06-2014 06:32 AM
There's no point in having him disable transcoding, it won't change a thing, he only has half DSP.
A HW CFB with PVDM2 requires the whole DSP for conferencing, unless you give up on using that half DSP for TDM termination and XCODER, and use it for a HW CFB, there's nothing to do here.
You need to buy more DSPs.
08-06-2014 07:09 AM
Hi
+5 for jamie ,i just asked him to disable transcoding because he didnot associate transcoding profile under sccp ccm group . Anyway so you have to purchase PVDM because you have to do hardware conference ..
Thanks
please rate all useful information
08-06-2014 03:56 AM
Apply below command under telephony-service and try once.
no conference hardware
Suresh
08-06-2014 04:29 AM
Hi
yes , you have to increase your PVDM resources to get enough resources to do hardware conference . Your resources is used by Voice-cards 0/0 & 0/1.Can you disable transcode profie as the below:-
dspfarm profile 1 transcode
shu
no max sessions 1
dspfarm profile 2 conference
max sessions ?
Note: keep in your mind , no need for conference hardware if the conference will be between g711 participants "software Conference will be enough", if the conference will be done with other g729 Prticipant so in this time you will need conference hardware.
Thanks
please rate all useful information
08-06-2014 06:32 AM
There's no point in having him disable transcoding, it won't change a thing, he only has half DSP.
A HW CFB with PVDM2 requires the whole DSP for conferencing, unless you give up on using that half DSP for TDM termination and XCODER, and use it for a HW CFB, there's nothing to do here.
You need to buy more DSPs.
08-06-2014 07:09 AM
Hi
+5 for jamie ,i just asked him to disable transcoding because he didnot associate transcoding profile under sccp ccm group . Anyway so you have to purchase PVDM because you have to do hardware conference ..
Thanks
please rate all useful information
05-11-2016 05:58 AM
Dear all
Greetings
Can someone help me please, I have CME running voice telephone and I would like to use it to run Cisco Telepresence, but I don't know how to do it.
Please support
Best Regards
ART
05-11-2016 08:02 AM
That is a complete different topic from the one on this thread, open a new thread for this. And also mention what material have you reviewed.
08-06-2014 06:43 AM
Hello,
I disabled the transcode profile. Max session is still at 0-0.
I need to make conference with g729 codec.
Thanks.
jb
08-06-2014 07:40 AM
Ok, so if i want to make conference in G729 (transcode needed so), I need to buy PVDM . Because i don't have enough resource for both conference/transcoding.
How can i calculate it?
Is that right?
Thanks.
JB
08-06-2014 08:02 AM
Use the DSP calculator online, you'll need at least, another half DSP, or a full DSP, depending on how many conferences you want.
08-06-2014 08:02 AM
Hi
kindly check the below link which will access you to DSP calculator which will help you
http://www.cisco.com/web/applicat/dsprecal/dsp_calc.html
Thanks
please rate all useful information
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide