Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About Suresh Hudda
06-15-2018
Stats
Member since
10-11-2012
1055
Posts
690
Helpful
130
Solutions
Created by
Suresh Hudda
in IP Telephony and Phones
in IP Telephony and Phones
06-07-2018
05:28 AM
06-07-2018
05:28 AM
I would suggest you to check with licensing@cisco.com first if they can re-host licenses for 8.6 ver, if they can, then either way you can choose. In above case you may need to re-host licenses after step 3 and before step 4.
Suresh
... View more
06-15-2017
11:52 PM
You should buy more licenses. If you have 25 session lic then you should allow only 25 simultaneous calls on cube router, although there is no restriction but if you allow more number of calls ((depends on hardware capacity as well)) than license count, its means you are violating agreement with Cisco.
As, CUBE is a paper-based honor license (no file to install) that allows you to run the CUBE Right-to-Use feature set after you have the UCK9 license installed.
A session is a single audio or a video call across the CUBE, regardless of call legs. Some vendors consider one call as two sessions. You may refer below document.
http://www.cisco.com/c/en/us/td/docs/ios-xml/ios/voice/cube/configuration/cube-book/voi-cube-licensing.html
Suresh
... View more
Created by
Suresh Hudda
in IP Telephony and Phones
in IP Telephony and Phones
06-12-2017
12:11 AM
06-12-2017
12:11 AM
Service provider can do this if they can. In callmanager/VG we cant do it because how do the system recognize & decide whether a call placed is std call or not as both dialed numbers are 10 digits numbers (and even they start with same digit e.g. 78).
Suresh
... View more
06-11-2017
11:26 PM
It can be interoperability issue with PSTN' service provider, I faced this issue once with MGCP gateway and ISDN E1 PRI then I changed the gateway as h323 and it worked. But, its worth to check with service provider first if you are sending correct digits to them.
Suresh
... View more
Created by
Suresh Hudda
in IP Telephony and Phones
in IP Telephony and Phones
06-11-2017
11:19 PM
06-11-2017
11:19 PM
Seems, service provider doesn't require 0 as a prefix for STD mobile calls that's why calls are going..for example in India you can dial std mobile number without using 0 (prefixing 0) so its not possible to restrict such dialing from any system.
Suresh
... View more
05-31-2017
11:57 PM
Try to remove itl file from phone or factory reset it once to check.
Suresh
... View more
Created by
Suresh Hudda
in IP Telephony and Phones
in IP Telephony and Phones
05-25-2017
11:10 PM
05-25-2017
11:10 PM
This is not the actual logs.., did you get chance to open it to read ? Seems you have not followed the procedure properly.
Suresh
... View more
Created by
Suresh Hudda
in IP Telephony and Phones
in IP Telephony and Phones
05-25-2017
02:06 AM
05-25-2017
02:06 AM
You need to configure serial port on VM for this, below is the link which you can refer for this.
https://supportforums.cisco.com/document/11936186/dumping-cucm-fresh-install-logs-virtualization
Suresh
... View more
Created by
Suresh Hudda
in IP Telephony and Phones
in IP Telephony and Phones
05-23-2017
04:48 AM
05-23-2017
04:48 AM
Can you please attach o/p of "show voice register global", and please take these logs during issue "debug ccsip message", "debug ccsip error" & "debug voice register events" and attach here.
I would upgrade the cme/ios version on router to latest available version if not done yet.
Suresh
... View more
Created by
Suresh Hudda
in IP Telephony and Phones
in IP Telephony and Phones
05-22-2017
10:58 PM
05-22-2017
10:58 PM
Hi Ajith, You can refer below table for exact format.
Property
Value
Bit Rate
64kbps
Audio Sample Size
8 bit
Channels
1 (mono)
Audio Sample Rate
8khz
Audio Format
CCITT U-law
... View more
Created by
Suresh Hudda
in IP Telephony and Phones
in IP Telephony and Phones
05-22-2017
10:19 PM
05-22-2017
10:19 PM
PCM encoding, 8 bits, 8 khz, mono. There are free tools, using one of them you can convert it to correct format.
Suresh
... View more
Created by
Suresh Hudda
in IP Telephony and Phones
in IP Telephony and Phones
05-22-2017
05:05 AM
05-22-2017
05:05 AM
Try to put "no supplementary-service sip refer" command under 'voice service voip' section and then check once please.
Suresh
... View more
Created by
Suresh Hudda
in IP Telephony and Phones
in IP Telephony and Phones
05-21-2017
10:27 PM
05-21-2017
10:27 PM
Typical scenarios include for cause value 34 is "No B-channels are available to make the selected call", do you have PRI up ? can u please attach output of "debug isdn 931" of a test call & "sh isdn st" and "sh run | s dial-peer" .
Suresh
... View more
05-20-2017
05:42 AM
Maximum gateways and trunks cucm can support is 2100 (regardless of gateway model), it depends on VM as well. For detailed information please go through its sizing tool/SRND, below is the link.
http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cucm/srnd/collab11/collab11/sizing.html#10983
Suresh
... View more
05-19-2017
01:30 AM
..And if you have 3rd party call billing application installed & VG has configured in CUCM as MGCP then you can pull utilization reports of pri from that billing application, otherwise you may ask service provider to provide utilization report if they can.
Suresh
... View more
Created by
Suresh Hudda
in IP Telephony and Phones
06-07-2018
06-07-2018
I would suggest you to check with licensing@cisco.com first if they can
re-host licenses for 8.6 ver...
06-15-2017
You should buy more licenses. If you have 25 session lic then you should
allow only 25 simultaneous ...
Created by
Suresh Hudda
in Unified Communications Infrastructure
06-12-2017
06-12-2017
Try to upgrade/downgrade firmware on couple of phones and check..seems
issue with phone firmware or ...
06-12-2017
Service provider can do this if they can. In callmanager/VG we cant do
it because how do the system ...
06-11-2017
It can be interoperability issue with PSTN' service provider, I faced
this issue once with MGCP gate...
06-11-2017
Seems, service provider doesn't require 0 as a prefix for STD mobile
calls that's why calls are goin...
Created by
Suresh Hudda
in Unified Communications Infrastructure
05-26-2017
05-26-2017
Have you added this in CUCM before initiating imp installation ? What is
the CUCM ver ? Can you atta...
05-25-2017
This is not the actual logs.., did you get chance to open it to read ?
Seems you have not followed t...
05-25-2017
You need to configure serial port on VM for this, below is the link
which you can refer for this.
ht...
05-24-2017
If you are using below services then these service should be activated.
Cisco XCP Directory Service ...
05-23-2017
Can you please attach o/p of "show voice register global", and please
take these logs during issue "...
05-22-2017
Hi Ajith, You can refer below table for exact format. Property Value Bit
Rate 64kbps Audio Sample Si...
05-22-2017
PCM encoding, 8 bits, 8 khz, mono. There are free tools, using one of
them you can convert it to cor...
Public Statistics
| Date Registered | 10-11-2012 09:51 PM |
| Date Last Visited | 06-15-2018 06:53 PM |
| Total Messages Posted | 1,055 |
| Total Helpful Votes Received | 690 |
Helpful Votes Given To
| User | Helpful Count |
|---|---|
| 5 | |
| 5 | |
| 5 | |
| 10 | |
| 5 |
.jpg "VIP Mentor"){kind=icon}
Helpful Votes From
Awards
Cisco Designated VIPs
2017 IP Telephony
Community Spotlight Award
Mobile User, April 2016
Community Spotlight Award
Questions Answered
