Hi all,
I am trying to build a home lab with 2800 Series router and switch 3560. I have configured the router and switch but the the phone is not getting registered. I am not sure if I am missing any configuration.
I am using 7941 phone and I see the message (term41.default OK) and it stucks there.
Here is the router config
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2013.05.26 16:19:20 =~=~=~=~=~=~=~=~=~=~=~=
sjo h run
Building configuration...
Current configuration : 2545 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Router
!
boot-start-marker
boot-end-marker
!
logging message-counter syslog
!
no aaa new-model
clock timezone central -8
clock summer-time zone recurring
no network-clock-participate wic 3
!
dot11 syslog
ip source-route
!
--More-- !
ip cef
ip dhcp excluded-address 192.168.10.1 192.168.10.9
ip dhcp excluded-address 192.168.20.1 192.168.20.9
!
ip dhcp pool VOICE_SCOPE
network 192.168.10.0 255.255.255.0
default-router 192.168.10.1
option 150 ip 192.168.100.3
!
ip dhcp pool DATA_SCOPE
network 192.168.20.0 255.255.255.0
default-router 192.168.20.1
!
!
no ipv6 cef
!
multilink bundle-name authenticated
!
!
!
!
!
--More-- !
!
voice service voip
allow-connections h323 to sip
allow-connections sip to sip
no supplementary-service sip moved-temporarily
no supplementary-service sip refer
sip
registrar server expires max 3600 min 3600
no update-callerid
!
!
!
voice class codec 1
codec preference 1 g711ulaw
codec preference 2 g729r8
!
!
!
!
!
!
!
--More-- !
!
!
!
!
!
!
!
!
voice-card 0
!
!
!
!
!
archive
log config
hidekeys
!
!
!
!
!
--More-- controller T1 0/3/0
!
controller T1 0/3/1
!
!
!
!
!
interface GigabitEthernet0/0
no ip address
duplex full
speed auto
!
interface GigabitEthernet0/0.10
description router interface for voice vlan
encapsulation dot1Q 10
ip address 192.168.10.1 255.255.255.0
!
interface GigabitEthernet0/0.20
description router interface for data vlan
encapsulation dot1Q 20
ip address 192.168.20.1 255.255.255.0
!
--More-- interface GigabitEthernet0/0.100
description administration
encapsulation dot1Q 100 native
ip address 192.168.100.2 255.255.255.0
!
interface GigabitEthernet0/1
no ip address
duplex auto
speed auto
!
interface Service-Engine1/0
no ip address
shutdown
!
ip forward-protocol nd
no ip http server
no ip http secure-server
!
!
!
!
!
!
--More-- !
!
!
!
control-plane
!
!
!
voice-port 0/1/0
!
voice-port 0/1/1
!
voice-port 0/2/0
!
voice-port 0/2/1
!
ccm-manager fax protocol cisco
!
mgcp fax t38 ecm
!
!
!
!
--More-- !
!
telephony-service
em logout 0:0 0:0 0:0
max-ephones 5
max-dn 10
ip source-address 192.168.10.1 port 2000
max-conferences 8 gain -6
transfer-system full-consult
create cnf-files version-stamp Jan 01 2002 00:00:00
!
ephone-dn 1
number 1000
!
!
ephone 1
device-security-mode none
mac-address FCFB.FBCA.4B34
type 7941
button 1:1
!
line con 0
line aux 0
line 66
no activation-character
no exec
transport preferred none
transport input all
transport output lat pad telnet rlogin lapb-ta mop udptn v120 ssh
line vty 0 4
login
!
--More-- scheduler allocate 20000 1000
end
Here are the 7941 files in flash
2494499 May 25 2013 19:25:32 apps41.8-3-2-27.sbn
42 547146 May 25 2013 19:26:18 cnu41.8-3-2-27.sbn
43 2452629 May 25 2013 19:26:50 cvm41sccp.8-3-2-27.sbn
44 530601 May 25 2013 19:28:22 dsp41.8-3-2-27.sbn
45 315827 May 25 2013 19:28:40 jar41sccp.8-3-2-27.sbn
46 638 May 25 2013 19:28:58 SCCP41.8-3-3S.loads
47 642 May 25 2013 19:29:12 term41.default.loads
48 642 May 25 2013 19:30:16 term61.default.loads
Here is the switch config
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2013.05.26 16:18:29 =~=~=~=~=~=~=~=~=~=~=~=
show run
Building configuration...
Current configuration : 2170 bytes
!
! Last configuration change at 02:29:19 UTC Mon Mar 1 1993
!
version 15.0
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Switch
!
boot-start-marker
boot-end-marker
!
!
no aaa new-model
system mtu routing 1500
ip routing
!
!
!
!
--More-- !
!
!
!
!
!
spanning-tree mode pvst
spanning-tree extend system-id
!
vlan internal allocation policy ascending
!
!
!
!
!
!
!
!
!
!
!
!
!
!
--More-- interface FastEthernet0/1
switchport trunk encapsulation dot1q
switchport trunk native vlan 20
switchport mode trunk
switchport voice vlan 10
spanning-tree portfast
!
interface FastEthernet0/2
switchport trunk encapsulation dot1q
switchport trunk native vlan 20
switchport mode trunk
switchport voice vlan 10
spanning-tree portfast
!
interface FastEthernet0/3
switchport trunk encapsulation dot1q
switchport trunk native vlan 20
switchport mode trunk
switchport voice vlan 10
spanning-tree portfast
!
interface FastEthernet0/4
switchport trunk encapsulation dot1q
switchport trunk native vlan 20
--More-- switchport mode trunk
switchport voice vlan 10
spanning-tree portfast
!
interface FastEthernet0/5
switchport trunk encapsulation dot1q
switchport trunk native vlan 20
switchport mode trunk
switchport voice vlan 10
spanning-tree portfast
!
interface FastEthernet0/6
switchport trunk encapsulation dot1q
switchport trunk native vlan 20
switchport mode trunk
switchport voice vlan 10
spanning-tree portfast
!
interface FastEthernet0/7
switchport trunk encapsulation dot1q
switchport trunk native vlan 20
switchport mode trunk
switchport voice vlan 10
spanning-tree portfast
--More-- !
interface FastEthernet0/8
!
interface FastEthernet0/9
!
interface FastEthernet0/10
!
interface FastEthernet0/11
!
interface FastEthernet0/12
switchport trunk encapsulation dot1q
switchport trunk native vlan 20
switchport mode trunk
switchport voice vlan 10
speed 100
duplex full
spanning-tree portfast
!
interface GigabitEthernet0/1
!
interface Vlan1
ip address 192.168.100.1 255.255.255.0
!
ip default-gateway 192.168.100.1
--More-- ip http server
ip http secure-server
!
!
!
!
line con 0
line vty 5 15
!
end
Switch#
*Mar 1 02:38:10.929: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/7, changed state to down
*Mar 1 02:38:11.944: %LINK-3-UPDOWN: Interface FastEthernet0/7, changed state to down
Switch#
Switch#
Switch#
Switch#
Switch#
Switch#
Switch#
Switch#
Switch#
*Mar 1 02:38:14.796: %LINK-3-UPDOWN: Interface FastEthernet0/7, changed state to up
Switch#
*Mar 1 02:38:16.826: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/7, changed state to up
Any help is much appreciated.. please
