cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Announcements

580
Views
10
Helpful
9
Replies
Beginner

CP3905 SSH Access - How To ?

Hi

 

I

 have several CP3905 using Sip Firmware working fine but i'd like to access then from SSH.  I did some conf like img bellow but i cant access ! 

What is wrong ? what is missing ?

Captura de Tela 2018-08-14 às 09.02.50.png 

 Thanks

1 ACCEPTED SOLUTION

Accepted Solutions
Highlighted
Cisco Employee

Re: CP3905 SSH Access - How To ?

the field for telnet is vendor config it looks like this

<vendorConfig>
<disableSpeaker>false</disableSpeaker><pcPort>0</pcPort><settingsAccess>1</settingsAccess><garp>0</garp><voiceVlanAccess>0</voiceVlanAccess><webAccess>0</webAccess><spanToPCPort>0</spanToPCPort><rtcp>0</rtcp><enableCdpSwPort>1</enableCdpSwPort><enableCdpPcPort>1</enableCdpPcPort><enableLldpSwPort>1</enableLldpSwPort><enableLldpPcPort>1</enableLldpPcPort><lldpAssetId></lldpAssetId><powerPriority>0</powerPriority><eapAuthentication>0</eapAuthentication><autobarge>1</autobarge><hookflash>0</hookflash><enableTelnet>2</enableTelnet><telnetUsername>admin</telnetUsername><telnetPassword>cisco</telnetPassword></vendorConfig>



notice how enable telnet is set to 2 and it also has telnet user name and password in the SEPMAC file.

9 REPLIES 9
Hall of Fame Community Legend

Re: CP3905 SSH Access - How To ?

When you SSH into the phone, you'll enter the username of "cisco" and the password of "cisco".
After this happens, it'll ask you "again" what the password is. You enter "debug".

This is incorrect.  See next response.

Hall of Fame Community Legend

Re: CP3905 SSH Access - How To ?

Apologies, my previous response is not-so-correct.
With the above configuration, you'll be asked to authenticate twice. The first time, the username & password will be "cisco".
This is then followed by the second and the response could either be "log/log" or "debug/debug" or "default/user".
Cisco Employee

Re: CP3905 SSH Access - How To ?

is the phone registered to a CME or CUCM server?
3905 does not support SSH. it only supports Telnet which needs to be enabled first on the CUCM for eg.
Hall of Fame Community Legend

Re: CP3905 SSH Access - How To ?


@Ishan Zutshi wrote:
is the phone registered to a CME or CUCM server?

Judging from the screenshot, I'd say neither.  The phone is being configured for Asterisk. 

Cisco Employee

Re: CP3905 SSH Access - How To ?

yeah. regardless of the call control (asterisk or cisco) this phone itself does not support SSH. It only support telnet so that will work, SSH won't.
Beginner

Re: CP3905 SSH Access - How To ?

Phone is registered at Asterisk.

 

I try ssh and telnet but it doesnt work, i change sshPort to 23 and it doesnt work too.

 

Since phone versions change some functionality i dont know what kind of parameter i need to put in SEPMAC file.

Hall of Fame Community Legend

Re: CP3905 SSH Access - How To ?

Well, as what Ishan said, try Telnet.
Highlighted
Cisco Employee

Re: CP3905 SSH Access - How To ?

the field for telnet is vendor config it looks like this

<vendorConfig>
<disableSpeaker>false</disableSpeaker><pcPort>0</pcPort><settingsAccess>1</settingsAccess><garp>0</garp><voiceVlanAccess>0</voiceVlanAccess><webAccess>0</webAccess><spanToPCPort>0</spanToPCPort><rtcp>0</rtcp><enableCdpSwPort>1</enableCdpSwPort><enableCdpPcPort>1</enableCdpPcPort><enableLldpSwPort>1</enableLldpSwPort><enableLldpPcPort>1</enableLldpPcPort><lldpAssetId></lldpAssetId><powerPriority>0</powerPriority><eapAuthentication>0</eapAuthentication><autobarge>1</autobarge><hookflash>0</hookflash><enableTelnet>2</enableTelnet><telnetUsername>admin</telnetUsername><telnetPassword>cisco</telnetPassword></vendorConfig>



notice how enable telnet is set to 2 and it also has telnet user name and password in the SEPMAC file.

Beginner

Re: CP3905 SSH Access - How To ?

It works now

 

Thanks all

and Thanks Ishan Zutshi

CreatePlease to create content
Content for Community-Ad
August's Community Spotlight Awards