Hello,
I need some help with setting up the maximum sessions on my conference and mtp dspfarm profiles.
Here is a "show inventory" of what I have:
NAME: "CISCO3945-CHASSIS", DESCR: "CISCO3945-CHASSIS"
PID: CISCO3945-CHASSIS , VID: V05 , SN:
NAME: "Cisco Services Performance Engine 150 for Cisco 3900 ISR on Slot 0", DESC
R: "Cisco Services Performance Engine 150 for Cisco 3900 ISR"
PID: C3900-SPE150/K9 , VID: V05 , SN:
NAME: "VWIC2-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - T1/E1 on Slot 0 SubSlot
0", DESCR: "VWIC2-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - T1/E1"
PID: VWIC2-2MFT-T1/E1 , VID: V01 , SN:
NAME: "1000BASE-LX SFP", DESCR: "1000BASE-LX SFP"
PID: TRF5735BALB302 , VID: A1A, SN:
NAME: "1000BASE-LX SFP", DESCR: "1000BASE-LX SFP"
PID: TRF5735BALB302 , VID: A1A, SN:
NAME: "VWIC2-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - T1/E1 on Slot 0 SubSlot
1", DESCR: "VWIC2-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - T1/E1"
PID: VWIC2-2MFT-T1/E1 , VID: V01 , SN:
NAME: "VWIC2-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - T1/E1 on Slot 0 SubSlot
2", DESCR: "VWIC2-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - T1/E1"
PID: VWIC2-2MFT-T1/E1 , VID: V01 , SN:
NAME: "VWIC2-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - T1/E1 on Slot 0 SubSlot
3", DESCR: "VWIC2-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - T1/E1"
PID: VWIC2-2MFT-T1/E1 , VID: V01 , SN:
NAME: "PVDM3 DSP DIMM with 64 Channels on Slot 0 SubSlot 4", DESCR: "PVDM3 DSP D
IMM with 64 Channels"
PID: PVDM3-64 , VID: V01 , SN:
NAME: "PVDM3 DSP DIMM with 256 Channels on Slot 0 SubSlot 5", DESCR: "PVDM3 DSP
DIMM with 256 Channels"
PID: PVDM3-256 , VID: V01 , SN:
NAME: "PVDM3 DSP DIMM with 256 Channels on Slot 0 SubSlot 6", DESCR: "PVDM3 DSP
DIMM with 256 Channels"
PID: PVDM3-256 , VID: V01 , SN:
NAME: "Network Module Adapter for SM Slot on Slot 1", DESCR: "Network Module Ada
pter for SM Slot"
PID: SM-NM-ADPTR , VID: V01, SN:
NAME: "High Density Voice2 Network module with on board two port interface on S
lot 1", DESCR: "High Density Voice2 Network module with on board two port interf
ace "
PID: NM-HDV2-2T1/E1 , VID: V05, SN:
NAME: "VWIC2-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - T1/E1 on Slot 1 SubSlot
0", DESCR: "VWIC2-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - T1/E1"
PID: VWIC2-2MFT-T1/E1 , VID: V01 ,
NAME: "C3900 AC Power Supply 1", DESCR: "C3900 AC Power Supply 1"
PID: PWR-3900-AC , VID: V01 , SN:
NAME: "C3900 AC Power Supply 2", DESCR: "C3900 AC Power Supply 2"
PID: PWR-3900-AC , VID: V01 , SN:
---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Here is partial show run of the the media resources along with the codecs I'm using:
sccp local Loopback0
sccp ccm 10.74.215.236 identifier 1 version 7.0
sccp ccm 10.74.15.228 identifier 2 version 7.0
sccp ccm 10.74.215.235 identifier 3 version 7.0
sccp ip precedence 3
sccp
sccp ccm group 1
description Media Resources
associate ccm 1 priority 1
associate ccm 2 priority 2
associate ccm 3 priority 3
associate profile 1 register CFB_RUKUA-B
associate profile 2 register MTP_RUKUA-B-G729BR8
associate profile 3 register MTP_RUKUA-B-G711
associate profile 4 register MTP_RUKUA-B-G729R8
dspfarm profile 1 conference
description OAB_HWCFB_1-B
codec g711ulaw
codec g711alaw
codec g729r8
maximum sessions ?
associate application SCCP
shutdown
dspfarm profile 2 mtp
codec g711ulaw
maximum sessions ?
associate application SCCP
dspfarm profile 3 mtp
codec g711alaw
maximum sessions software ?
associate application SCCP
dspfarm profile 4 mtp
codec g729r8
maximum sessions software ?
associate application SCCP
I'm looking to use the IOS router as both a conference bridge and for mtp resources. I am unsure as to how many maximum sessions to use. Any help would be appreciated. Thank You!
